Runco dtv-992/992 ultra manual Access to EYE-QTMON-SCREEN Menus, Eye-Qtmmenu

Page 54

Appendix 2

ON- SCREEN OPERATING INSTRUCTIONS

ACCESS TO EYE-QTMON-SCREEN MENUS

After the EYE-QTMunit has been correctly installed in the pro- jector, press the <ADJUST> button on the RCU (Remote Control Unit) or the local keypad of the projector to enter the ‘Adjustment mode’

(please refer to the projector Owner’s Manual). The EYE-QTMpath will be displayed in the menu:

Highlight EYE-QTMby pushing the or keys of the control disc (on RCU).

Press the <ENTER> button to enter the EYE-QTMmenu.

EYE-QTMMENU

The EYE-QTMmenu will be displayed after the path EYE-QTMis selected. Six items are available:

TOUCHUP.

AUTOCONVERGENCE.

QUICKAUTOPICTURE.

FULLAUTOPICTURE.

EYE-QTMSETUP.

EYE-QTMDIAGNOSTICS.

Choose EYE-QTMSETUP first to carry out the SETUP proce- dures.

Use EYE-QTMDIAGNOSTICS to check whether the EYE-QTMis functioning normally.

ADJUSTMENT MODE

Select a path from below:

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 1

Select with or then <ENTER>.

<EXIT> to return

EYE-Q

TOUCH UP

AUTOCONVERGENCE

QUICK AUTOPICTURE

FULL AUTOPICTURE

EYE-Q SETUP

EYE-Q DIAGNOSTICS

Select with or then <ENTER>.

<EXIT> to return

APX-3

Image 54

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3EYE-QTMDIAGNOSTICS Safety Instructions Installation InstructionsSafety Instructions Location and Function of Controls Rear Panel TerminologyFront Panel Terminology Control panel terminology Local KeypadRCU control panel terminology IR Transmission Indicator Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsSignal Input Connection to the Projector Start up with full white imagePort No Projector Input Press Digit Button Rgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection Remote control YYB-Y3S or R-YY3sB-Y input selectionData communications Battery installation in the RCU ControllingHow to display a projector address? How to use your RCUUsing your RCU Hardware set up of the projector addressGeneral Access Menu Items Source Input selectionAnalog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeStart Up of the Adjustment Mode Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalancePress Enter to display the color select menu PeakingColor Select Display the projected image in that specific colorFocusing FocusingPhase Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WLeft Side Correction Left Side Correction Left Keystone Left BOWTop-Bottom north-south Adjustments TOP Bottom N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments Blanking TOP Bottom Left RightConvergence Adjustment Coarse Convergence AdjustmentsConvergence Fine Convergence Adjustments Vertical cornersService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Identification IdentificationCopy a block Copy a BlockDelete a Block Deletion of blocksDeleting block by block Delete ALL BlocksChange password Change LanguageTotal Run Time Convergence mid All settings to midpositionUndo all settings to midpos Undo R & B convergence midDynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correctionCRT run in cycle G2 AdjustmentCommon Settings 12C Diagnostics CRT RUN in Cycle Projector Warm UPProjector warm up Projector Warm UPMESSAGES, WARNINGS, and Failures SourceFailure DTV-992 DTV-992 UltraAppendix RS 232 ControlSending a Record single instruction Decimal values STXSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewCompact, built-in system Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Preparing your EYE-QTMAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFTOUCH-UP on Timer Adjusting Other SourcesReference Source What is Being Measured by EYE-QTM Learning a ReferenceAdjusting Screen Size On Current SourceTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev