Runco dtv-992/992 ultra manual Change password, Change Language, Total Run Time

Page 40

Service Mode

Change password

This item is password protected.

Highlight ‘Change Password’ with the control disc and press

ENTER.

ENTER gives a confirmation message before deleting. EXIT returns to the Path Selection main menu.

The current password is displayed. The new password must consist of 4 digits between 0 and 9. Push the control disc to the left or to the right to select the digits to be changed. Use the numeric keys to enter the new digits.

Press ENTER to save the new password. Before saving the new password, a confirmation screen will be displayed.

Press EXIT to return to the Projector Set-up menu without saving the new password.

When the displayed password is correct, press ENTER to save. If not correct, press EXIT to cancel the saving.

ENTER saves the entered password.

EXIT returns without saving.

Change Language

The ‘Change Language’ function offers the possibility to change the language of the screen menus to :

-English

-Spanish

-French

-German

Highlight ‘Change Language’ with the control disc and press

ENTER saves the entered password.

EXIT returns without saving.

ENTER.

Push the control disc up or down to select the desired language and press ENTER to change the language.

Total Run Time

Highlight ‘Total Run Time’ with the control disc and press ENTER to display the amount of time the projector has played since its first start up at the factory.

ENTER gives the selected item.

EXIT returns to Service mode menu.

ADJUST returns to the Operational mode.

Note : all projectors leave the factory after a burn-in period of approximately 100 hours.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

CHANGE PASSWORD

Enter new password :

0 0 0 0

CHANGE PASSWORD

Password will be

reprogrammed as XXXX

<ENTER> to confirm <EXIT> to cancel

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

LANGUAGE

ENGLISH

~

ESPANOL

FRANCAIS

DEUTSCH

Select with or then <ENTER> <EXIT> to return.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE: operating

Select with or then <ENTER> <EXIT> to return.

7-4

Image 40

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3EYE-QTMDIAGNOSTICS Safety Instructions Installation InstructionsSafety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator AC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsStart up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button Connecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Battery installation in the RCU ControllingHow to use your RCU Using your RCUHow to display a projector address? Hardware set up of the projector addressGeneral Access Menu Items Source Input selectionAnalog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeStart Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalancePeaking Color SelectPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingGeometry Adjustments Horizontal Phase AdjustmentPhase GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WLeft Side Correction Left Side Correction Left Keystone Left BOWTop-Bottom north-south Adjustments TOP Bottom N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments Blanking TOP Bottom Left RightCoarse Convergence Adjustments Convergence AdjustmentConvergence Fine Convergence Adjustments Vertical cornersStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Identification Copy a blockIdentification Copy a BlockDeletion of blocks Deleting block by blockDelete a Block Delete ALL BlocksChange Language Change passwordTotal Run Time All settings to midposition Undo all settings to midposConvergence mid Undo R & B convergence midDynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correctionG2 Adjustment Common Settings 12C DiagnosticsCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector warm up Projector Warm UPMESSAGES, WARNINGS, and Failures SourceFailure DTV-992 DTV-992 UltraAppendix RS 232 ControlSending a Record single instruction Decimal values STXSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry systemCompact, built-in system Preparing your EYE-QTMAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFAdjusting Other Sources TOUCH-UP on TimerReference Source What is Being Measured by EYE-QTM Learning a ReferenceAdjusting Screen Size On Current SourceAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev