Runco dtv-992/992 ultra manual Geometry Adjustments, Horizontal Phase Adjustment

Page 28

Random Access Adjustment Mode

Geometry Adjustments

The geometry adjustments have to be done only on the green image. These adjust- ments are automatically implemented for the other color images : Left-right (EW) and Top-Bottom Corrections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical Linearity and Horizontal Phase.

Highlight GEOMETRY by pushing the control disc up or down and press ENTER to display the geometry menu.

ENTER will display Geometry menu.

EXIT will return to Internal Crosshatch Selection or Setup Pattern Selection Menu.

ADJUST returns to operational mode.

Within the Geometry Adjustment menu, the following adjustments are available :

-Horizontal Phase (not for internal # pattern).

-Raster Shift

-Left-Right Corrections

-Top-Bottom Corrections

-Horizontal Size

-Vertical Linearity

-Vertical Size

-Blanking

The convergence corrections are disabled during geometry corrections. The blanking corrections are only enabled during the blanking adjustments.

Horizontal Phase Adjustment

Push the control disc up or down to highlight H PHASE on Geometry menu and the press ENTER.

Note : No horizontal phase adjustment is available on the internal # pattern.

For external sources :

If the raster shift is correctly adjusted, the H Phase text box is projected in the mid- dle of the raster. At that moment, the “><” icon indicates the middle of the raster. Adjust the H Phase control until the middle of the projected image is equal with the middle of >< icon.

Note : If the genlocked pattern was selected, the external source will be displayed.

A bar scale and a number indicator (between 0 and 100) on the screen give a visu- al indication of the horizontal phase adjustment.

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

COLOR SELECT

GEOMETRY

H PHASE

RASTER SHIFT

LEFT - RIGHT (E-W)

TOP - BOTTOM (N-S)

SIZE

V LINEARITY

BLANKING

Select with or then <ENTER> <EXIT> to return.

GEOMETRY

H PHASE

RASTER SHIFT

LEFT - RIGHT (E-W)

TOP - BOTTOM (N-S)

SIZE

V LINEARITY

BLANKING

X

H PHASE

70

ENTER continues to geometry menu.

X

H PHASE

Push the control disc to the right to correct

Push the control disc to the left to correct

X

H PHASE

70

70

6-6

Image 28

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3EYE-QTMDIAGNOSTICS Safety Instructions Installation InstructionsSafety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator AC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsStart up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button Connecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Battery installation in the RCU ControllingHow to use your RCU Using your RCUHow to display a projector address? Hardware set up of the projector addressGeneral Access Menu Items Source Input selectionAnalog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeStart Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalancePeaking Color SelectPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingGeometry Adjustments Horizontal Phase AdjustmentPhase GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WLeft Side Correction Left Side Correction Left Keystone Left BOWTop-Bottom north-south Adjustments TOP Bottom N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments Blanking TOP Bottom Left RightCoarse Convergence Adjustments Convergence AdjustmentConvergence Fine Convergence Adjustments Vertical cornersStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Identification Copy a blockIdentification Copy a BlockDeletion of blocks Deleting block by blockDelete a Block Delete ALL BlocksChange Language Change passwordTotal Run Time All settings to midposition Undo all settings to midposConvergence mid Undo R & B convergence midDynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correctionG2 Adjustment Common Settings 12C DiagnosticsCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector warm up Projector Warm UPMESSAGES, WARNINGS, and Failures SourceFailure DTV-992 DTV-992 UltraAppendix RS 232 ControlSending a Record single instruction Decimal values STXSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry systemCompact, built-in system Preparing your EYE-QTMAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFAdjusting Other Sources TOUCH-UP on TimerReference Source What is Being Measured by EYE-QTM Learning a ReferenceAdjusting Screen Size On Current SourceAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev