Runco runco super hdtv dtv video projector, dtv-992/992 ultra manual APX-16

Page 67

Appendix 2

In case of failures, the error message will shown: FAILED... Error 11; or

FAILED... Error 12; or FAILED... Error 13; or FAILED... Error 14; or FAILED... Error 15.

During the Sync Test, the following messages will displayed one after another on the screen:

Config for Sync;

Config for sync OK;

Horizontal Sync Test;

Horizontal Sync OK;

Vertical Sync Test;

Vertical Sync OK;

Frame and Field Test;

Frame and Field OK;

Sync Test OK.

In case of failures, the error message will be shown: FAILED... Error 21; or

FAILED... Error 22; or FAILED... Error 23; or FAILED... Error 24; or FAILED... Error 25; or FAILED... Error 26; or Sync Test Error 27 No syncs found

Check Camera & Cabling.

During the Ram Test, the following messages will displayed one after another on the screen:

Config for Ram;

Config for Ram OK;

Ram Data Line Test;

Ram Data Lines OK;

Ram Address Lines Test;

Ram Address Lines OK;

Ram Full Content Test;

Ram Full Content OK;

Ram Test OK

In case of failures, the error message will be shown:

FAILED... Error 31; or

FAILED... Error 32; or

FAILED... Error 33; or

FAILED... Error 34.

If all the tests are successful, the EYE-EYE-QTMmenu will be as follows:

Press the <EXIT> button to return to the EYE-™

TM

EYE-QDIAGNOSTICS

Interferance Test PASS

Generic Test	PASS
Sync Test	PASS
Ram Test	PASS

EYE-Q TM has been given

a clean bill of HEALTH.

APX-16

Image 67

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6EYE-QTMDIAGNOSTICS Installation Instructions Safety InstructionsSafety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator Connections AC Power mains Cord ConnectionPower Check Switching On/OffStart up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button RGB3S or RG3sB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Controlling Battery installation in the RCUHardware set up of the projector address How to use your RCUUsing your RCU How to display a projector address?Input selection General Access Menu Items SourcePause key Analog Picture ControlsAdjustment mode Start UP of the Adjustment ModeStart Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternColor Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow AdjustmentDisplay the projected image in that specific color PeakingColor Select Press Enter to display the color select menuFocusing FocusingGeometry Geometry AdjustmentsHorizontal Phase Adjustment PhaseRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsLeft Side Correction Left Keystone Left BOW Left Side CorrectionTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Blanking TOP Bottom Left Right Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Copy a Block IdentificationCopy a block IdentificationDelete ALL Blocks Deletion of blocksDeleting block by block Delete a BlockChange Language Change passwordTotal Run Time Undo R & B convergence mid All settings to midpositionUndo all settings to midpos Convergence midArrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustmentCRT RUN in Cycle Projector Warm UP G2 AdjustmentCommon Settings 12C Diagnostics CRT run in cycleProjector Warm UP Projector warm upSource MESSAGES, WARNINGS, and FailuresFailure DTV-992 Ultra DTV-992RS 232 Control AppendixSending a Record single instruction STX Decimal values$02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C SharpnessOverview Quick Guide to using the EYE-QTMsystemPreparing your EYE-QTM Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in systemEYE-QTMMENU Access to EYE-QTMON-SCREEN MenusSetting the Configuration EYE-QTMSETUPFocusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAdjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev