Runco dtv-992/992 ultra manual Selecting Setup Pattern, Internal Cross Hatch Pattern

Page 24

Random Access Adjustment Mode

Selecting Setup Pattern

If an external source is connected to the projector, this menu will be displayed. Push the control disc up or down to highlight the desired setup pattern and then press

ENTER.

Genlocked pattern : internally generated cross hatch pattern, locked on the external source.

Internal # pattern : internally generated cross hatch pattern and locked on internal generated sync signals. (no external source necessary)

ENTER continues to Random Access Adjustment Mode or Internal # Pattern Selection.

EXIT returns to Path Selection menu. ADJUST returns to Operational mode.

If no external source is connected to the projector, the internal cross hatch pattern menu will be displayed.

Note: The menus in the manual are created for an external source, connected to one of the inputs, and the ‘Genlocked Pattern’ is selected.

Internal Cross Hatch Pattern

The internal # pattern menu will be displayed if the internal cross hatch pattern has been selected or if no source is connected to the projector.

The table below lists the 8 fixed factory preset frequencies available. Another 8 blocks are custom programmable.

Push the control disc up or down to highlight the desired cross hatch frequency. Push the control disc to the left or to the right to scroll to another page. Press ENTER if the desired block is selected.

15.6/50	PAL/SECAM
15.7/60	NTSC
31.2/50	EDTV
31.5/60	IDTV
31.2/50	HDTVEUREKA
31.5/60	HDTV ATV
33.7/60	HDTV HIVISION
15.8/60	EGA 1
21.8/60	EGA 2
31.5/60	VGA 3
31.5/70	XGA 1,2
35.5/97	VGA 4
44.2/70	SUPER VGA 2
48.5/60	SUPER VGA 1
61.0/76	SUPER VGA 3
63.9/76	APOLLO

ENTER continues to the Random Access Adjustment Mode. EXIT returns to the Setup Pattern Selection menu.

Choose a setup pattern from below :

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

Source 01

Select with or then <ENTER> <EXIT> to return

INTERNAL # PATTERN

kHz / Hz
15.6/50	PAL/SECAM
15.7/60	NTSC
31.2/50	EDTV
31.5/60	IDTV
31.2/50	HDTV EUREKA
31.5/60	HDTV ATV
Select with		or
scroll with		or

<ENTER> to accept <EXIT> to return

6-2

Image 24

Contents DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3EYE-QTMDIAGNOSTICS Safety Instructions Installation InstructionsSafety Instructions Location and Function of Controls Rear Panel TerminologyFront Panel Terminology Control panel terminology Local KeypadRCU control panel terminology IR Transmission Indicator AC Power mains Cord Connection Power CheckSwitching On/Off ConnectionsSignal Input Connection to the Projector Start up with full white imagePort No Projector Input Press Digit Button Connecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection Remote control YYB-Y3S or R-YY3sB-Y input selectionData communications Battery installation in the RCU ControllingHow to use your RCU Using your RCUHow to display a projector address? Hardware set up of the projector addressGeneral Access Menu Items Source Input selectionAnalog Picture Controls Pause keyStart UP of the Adjustment Mode Adjustment modeStart Up of the Adjustment Mode Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternRandom access adjustment mode selection menu Picture TuningSync Fast/Slow Adjustment Color BalancePeaking Color SelectPress Enter to display the color select menu Display the projected image in that specific colorFocusing FocusingGeometry Adjustments Horizontal Phase AdjustmentPhase GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WLeft Side Correction Left Side Correction Left Keystone Left BOWTop-Bottom north-south Adjustments TOP Bottom N-SSize Adjustment Vertical Linearity AdjustmentLinearity Blanking Adjustments Blanking TOP Bottom Left RightConvergence Adjustment Coarse Convergence AdjustmentsConvergence Fine Convergence Adjustments Vertical cornersService Mode Starting up the Service modeOverview flowchart ‘Service’ mode Identification Copy a blockIdentification Copy a BlockDeletion of blocks Deleting block by blockDelete a Block Delete ALL BlocksChange password Change LanguageTotal Run Time All settings to midposition Undo all settings to midposConvergence mid Undo R & B convergence midDynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correctionG2 Adjustment Common Settings 12C DiagnosticsCRT run in cycle CRT RUN in Cycle Projector Warm UPProjector warm up Projector Warm UPMESSAGES, WARNINGS, and Failures SourceFailure DTV-992 DTV-992 UltraAppendix RS 232 ControlSending a Record single instruction Decimal values STXSharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5CQuick Guide to using the EYE-QTMsystem OverviewEasy-to-use, high precision automatic convergence system Easy-to-use, high precision automatic geometry systemCompact, built-in system Preparing your EYE-QTMAccess to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMSETUP Setting the ConfigurationFocusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFTOUCH-UP on Timer Adjusting Other SourcesReference Source What is Being Measured by EYE-QTM Learning a ReferenceAdjusting Screen Size On Current SourceTOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev