Panasonic WJ-HD220 manual Post-alarm Recording Post ALM REC, Dynamic Recording Dynamic REC

Page 27

Post-alarm Recording (POST ALM REC)

This setting specifies the duration of alarm recording after an alarm input. Functions active during alarm recording are buzzer beeping, ALARM LED indication, "ALARM" status display, and the ALARM OUT signal.

1.Move the cursor to POST ALARM REC with the [D] or [C] button.

2.Select the desired duration with the JogDial. The default value is 10 seconds.

The unit will revert to the previous status when the time has elapsed.

Available times (seconds): 5, 10, 20, 30

Available times (minutes): 1, 1.5, 2, 3, 6

Continue: Recording continues until the [RESET] but- ton is pressed, or the RESET IN signal is supplied to the rear panel.

Manual: Recording continues for as long as the alarm input is active, or at least for 10 seconds if the input turns inactive earlier.

Dynamic Recording (DYNAMIC REC)

This setting specifies the recording pattern on the disk when one or more alarms operate.

1.Move the cursor to DYNAMIC REC with the [D] or [C] button.

2.Select the parameter with the JogDial, and press the JogDial.

The default is OFF.

ALM-MULTI:Alarmed channels are recorded with pri- ority over others.

OFF: All channels are recorded with the same priority.

Trigger Action Setup (TRIGGER ACTION SETUP)

This setting specifies the two roles of alarm recording and alarm control functions (Refer to page 47) in the post-alarm sequence.

TRIGGER ACTION SETUP

CAM

MODE

PRESET

1

REC&ALM

––

2

REC&ALM

––

3

REC&ALM

––

4

REC&ALM

––

5

REC&ALM

 

6

REC&ALM

 

7

REC&ALM

 

8

REC&ALM

 

When combination cameras are connected to VIDEO IN 1-4 on the rear panel, you can select a preset position for cam- eras 1-4. The camera will move to the preset position when an alarm other than VMD arises for the camera.

Notes:

The preset position assignment on the TRIGGER ACTION SETUP menu is not available for each PROG n (1 - 4) SETUP menu, but available only for the REC SETUP menu.

You need to preset desired positions for the camera prior to operation.

VMD will not move the camera to the preset position.

1.Move the cursor to TRIGGER ACTION SETUPO, and press the JogDial.

The TRIGGER ACTION SETUP menu opens.

2.Move the cursor to the channel.

3.Select a mode with the JogDial, and press the JogDial. The default is REC&ALM.

OFF: Disables alarm recording or warning.

REC&ALM: Enables both alarm recording and warning.

REC: Enables alarm recording, but disables warning.

4.The cursor is at the PRESET column. Select a preset parameter with the JogDial, and press the JogDial.

1-64:Moves the camera to the specified preset posi- tion.

HOME: Moves the camera to the home position.

–:Does not move the camera.

5.Repeat steps 2, 3 and 4 until all channels are set.

6.Press the [SETUP/ESC] button to return to the PROG1 SETUP, NO. 1 menu.

Camera Recording Setup (CAM REC SETUP)

This setting is provided for the purpose of saving disk space. Setting allows each camera channel to be enrolled in all recording modes or exclusively in alarm recording.

CAM REC SETUP

CAMMODE

1REC

2REC

3REC

4ALM-ONLY

5REC

6ALM-ONLY

7REC

8REC

1.Move the cursor to CAM REC SETUP, and press the [SET] button. The CAM REC SETUP menu opens.

2.Move the cursor to the camera channel with the [D] or [C] button.

27

Image 27
Contents Operating Instructions English Version Important Safety Instructions Contents Features PrefaceTrademarks Precautions Front View 7Stop and Setup/Escape Button Stop SETUP/ESC 4HDD Access Indicator HDD5FULL Indicator Full 6Error indicator Error@7Video Out Video OUT @6Audio OutRear View Installation Places to avoidAbout mounting Mounting in the Rack Basic System Connections & DIP SW SettingPS Data System Network System Personal computers can access the WJ-HD220 via the networkSystem Camera Connection ALARM/REMOTE ConnectionConnection with the Camera Site Connection with the MonitorsAlarm Connection Time Adjusting ConnectionExternal Recording Connection Serial Port Connections RS-232C ConnectionPS Data Connection Case 2 Exclusively with System Controller 10/100BASE-T Port ConnectionData Port Termination System ModeTurning Off the Power Setup ProceduresPrior to Setup Turning On the PowerJogDial Counter-clockwise Decreases the parameter Buttons and Dials Used for SetupDisplaying WJ-HD220 Main Menu Closing WJ-HD220 Main MenuMenu Tree PROG2 SetupInitializing Initializing All Contents & Setup DataInitializing Setup Data Initializing Settings for Network Setup MenuTimer Recording Setup Timer REC Program 1-4 Setup PROG1-4Main Menu WJ-HD220 Main Menu Recording Mode Setup PROG1-4 SETUP, no Alarm Recording Mode Setup ALMPre-alarm Recording PRE ALM REC Dynamic Recording Dynamic REC Post-alarm Recording Post ALM RECTrigger Action Setup Trigger Action Setup Camera Recording Setup CAM REC SetupClock Clock Manual Recording Setup RECExternally Specified Recording Mode EXT REC Setup Display Setup Display SetupStatus Position Status Posi Time & Date Position TIME&DATE PosiTime & Date Embedded TIME&DATE EMB Status Display Status DispDisk Capacity Warning HDD Full Remote LED Remote LEDDisk Check HDD Check System Setup System Setup Camera Title Camera Title~ 9 a ~ Z ! % ? ← → ↑ ↓ Password Lock Setup Password Lock Keylock Buzzer Setup Keylock BuzzSkip Alarm Recall Setup Disk End Mode Setup Alteration Detection SetupSimultaneous Recording & Playback Simul REC&PLAY Disk End Buzzer Disk END Buzz Play Priority Setup Play PriorityTime Adjust Setup Auto Erasing SetupResolution Resolution HDD Safety Mode HDD Safety Mode Video Motion Detection VMD Setup Alarm Setup Alarm SetupAlarm Buzzer Alarm Buzz Monitor Mode Monitor ModeCommunication Setup Serial Port SetupProtocol Protocol Control Unit Address CTL-UNIT Address only for PS Data Baud Rate Baud RateData Bit Data BIT Wait Time Wait TimeAssignable numbers Network Setup Network SetupAlarm Data Alarm Data exclusive to PS Data Line Speed Line SpeedSwitcher Setup Switcher Setup Available durations 2-30S Multiscreen Sequence Setup Multi SEQ SetupSpot Sequence Setup Spot SEQ Setup Camera View Setup Camera View SetupSystem Information System Log System LOG Language LanguageViewing a Single Live Operating ProceduresOn the Spot Monitor Selecting the Spot MonitorViewing a Quad Live Sequence On the Multiscreen MonitorSelecting the Multiscreen Monitor Zooming a Single LiveAlarm Output Alarm InputResetting Alarm Alarm Log Recall & Search Suspending Alarm InputInternal Timer Recording To Search for PlaybackTo Erase Log Power-on Recording Alarm RecordingManual Recording Step Playback Alarm Search PlaybackNormal Playback Skip PlaybackPicture record of a specified time and date is played back Time & Date Search PlaybackEnabling Button Lock Password VerificationWJ-HD220 Display PreparationsSystem Requirements BrowserConnection with a Client PC via Hub ConnectionDirect Connection with a PC System ExpansionMain Page and Control Panel About Picture QualityRecorder Status Displayed Quality Timer Recording Timer REC WJ-HD220 SetupTo Access Setup Menus Timer Setup Timer SetupAssignable programs PROG1 PROG4, OFF Program Assignment Timer RECProgramming Program Setup Recording Mode Setup PROG1-4 NO.1-4 SetupTrigger Action Setup Trigger Action Setup Camera Recording Setup REC Manual Recording Setup REC SetupCamera Preset Position Preset Status Display Status Display Clock Setup Clock SetupTime and Date Position TIME&DATE Position Time & Date Embedded TIME&DATECamera Title Camera Title Disk End Buzzer Disk END Buzzer Disk End Mode Disk END ModeTime Adjusting Time Adjusting Alteration Detection Alter DetectVMD Area Setup VMD Area Setup Video Motion Detector Setup VMD SetupData Bit Data BIT Alarm Data Alarm DataProtocol Selection Protocol Select Baud Rate Baud RateOnly for Psdata Camera System SetupDomain Name Service Domain Name Service Dynamic DNS Dynamic DNSSimple Network Management Protocol Camera View Setup Camera View Setup Common Setup Common SetupMultiscreen Sequence Setup Spot-screen Sequence SetupTime Time Multi Sequence Setup MultiCamera View Setup Camera View Setup Camera Channel Camera CHSystem Information System Information Error Information FTP, SMTP, Ddns Network Configuration User Setup User SetupHost Setup Host Setup FTP Client Setup FTP Client Setup Basic Setup Basic SetupFTP Send by Periodic Timer FTP Send by Periodic Timer Delete Mail Address Delete Mail Address Mail Setup Mail SetupAlarm Mail Setup Alarm Mail Setup Set Mail Address SET Mail AddressVideo Rate Video Rate Network Video SetupLive & Playback Image Setup Live & Play Image Setup Live Sequence Setup Live Sequence SetupMain Panel Operating WJ-HD2202End Time Display Area Start Button Start0Start Time Display Area 1End Button ENDMain Control Panel PAN/TILT Control Camera Control View Button Camera Control ViewAlarm List Http Download and Viewing Images Troubleshooting When accessing via the networkPhenomenon Cause What to do Specifications & Appendix Specifications Standard Accessories Appendix Remote Control from System ControllerTime and date selection For Time&Date search Implement Time&DateSearch Transmission Command Response CommandRS-232C Communication Protocol Command Table Alarm ControlBasic Operation Setup Control Miscellaneous ControlData Log Control Inquiry Media ControlHDD Maintenance When to Maintain HDD Who to Maintain HDDPower-on Procedures When Error Indicator is Lit When Full Indicator is Lit Resetting Disk EndDisk Menu Abbreviation Status Required CapacityAuto-remove Formatting HDD HDD Format Removing Logical Link Remove LinkNOW Formatting HDD Format SET Done Restarting RestartMail Contents Network Security WJ-HD220 Security FunctionFor More Security Type Message Details Network Error InformationSmtp Errors FTP Errors102 Ddns ErrorsNs0805-0 V8QA6335AN Imprimé en Chine