Panasonic WJ-HD500A manual Power UP Procedure

Page 27

POWER UP PROCEDURE

Before operating the Disk Recorder, confirm that the cam- eras and peripherals are connected correctly and securely and all system components are turned on.

1.Turn on the Disk recorder by pressing the POWER switch located on the rear of the Disk Recorder. Make sure that the OPERATE indicator on the front panel is illuminated.

2.After you completed the start, the Disk Recorder will run through a series of instructions for the system on the Multiscreen Monitor.

[ SYSTEM CHECK ]

PLEASE WAIT

3.If the Disk Recorder is powered up successfully, the display as shown below appears, then the camera images appear on the monitor screen.

[ SYSTEM CHECK ]

SYSTEM CHECK DONE!

PLEASE WAIT

DISK MENU: [SETUP] KEY

Note:

If during a system check the display shown below appears on the monitor screen, it will be followed by the DISK MENU after five seconds.

[ SYSTEM CHECK ]

YOU HAVE TO CONFIGURE DISKS

PLEASE WAIT

DISK MENU
MAIN 1:¢¢GB 2:¢¢GB
EXT5 1:¢¢GB 2:¢¢GB			3:¢¢GB 4:¢¢GB
EXT4	1:*	2:*	3:ADD	4:ADD
EXT3	1:LOST	2:LOST	3:LOST	4:LOST
EXT2	1:LOST	2:LOST	3:LOST	4:LOST
EXT1	1:-	2:-	3:-	4:-
EXT0	1:-	2:-	3:-	4:-

EXT DVD:-

REMOVE FORMAT

RESTART

SELECT ITEM AND PRESS [SET] KEY

The DISK MENU-Display indicates the status of the hard disks, and shows the causes why this menu was called up.

•Optional Extension Unit is installed [ADD] Requires disk formatting in the Extension

Unit.

•Replaced Hard Disk [✽]

Requires disk formatting for a replaced

Hard Disk.

•Detached Hard Disk [LOST]

Requires disk relocation in the system.

•Hard Disk malfunctions [✽]

Refer servicing to qualified service per- sonnel.

¢¢GB indicates the hard disk capacity.

Note:

If the Disk Recorder is left in this state for about five minutes, it will automatically restart by reconfiguring the system (disk remove).

Normal camera images will appear on the monitor screen.

28

Image 27

Contents Operating Instructions English Version Contents Easy image search FeaturesPreface Reliable recording of eventsDo not attempt to disassemble the appliance PrecautionsFully charge up the backup battery Do not drop metallic parts through slotsFront View 2Set Button SET @4Alarm Search Button Alarm Search@8Setup/Escape Button SETUP/ESC 1Numeric Buttons 1$2Spot Output Connector Spot OUT #0Full Indicator Full#1Hard Disk Drive Indicator HDD $1Multiscreen Output Connector Multiscreen OUT8Power Switch Power ON/OFF $7Alarm Port Alarm$9Mode Selector Mode 2Gen-lock Output Connector GEN-LOCK OUTWV-CU50 Remote Controller 6Electronic Zoom Button EL-ZOOM 9Alarm Search Button Alarm Search1Link Indicator Link Blinking Pause mode 0JogDialInstalling the Optional Hard Disk InstallationInstalling the Optional Motion Detector Board Installing the Optional Network Board Mounting into the Rack Shown below are examples of system connections ConnectionsBasic System System ExpansionConnection with the Remote Controller Connection with the Camera SitesConnection with the Monitors Alarm Alarm Port ConnectionControl Port Connection Connection with Control output Connection with the Uninterrupted Power Supply UPSMode Switch SettingConnection with the Extension Units Scsi ConnectionSwitch Settings Connection with the DVD Extension UnitConnection with the DVD Extension Unit without HDD Scsi ID=0 to Connection with the DVD Extension Unit with HDDConnection to PSData Compatible Equipment Mode Selector Setting10/100BASE-T Port Connection Serial Port ConnectionPreparations Power UP Procedure Formatting the Hard Disk 1DISK Format Formatting the DVD-RAM Disk Mirroring Function To deactivate the mirror function Disk Remove Time Display Monitors and DisplaysSpot and Multiscreen Monitor Status DisplayElectronic Zoom Display Format Error orSystem Status Display Group DisplayEmergency Recorder Timer RecorderHard Disk Manual RecorderTime Lapse Recording Multi Shot RecordingDynamic Recording is set to OFF Dynamic Recording is set to ALM-ONLY One Shot RecordingSetup Procedures Displaying the Setup Menu Setup MenuProgramming Menu Setup Setup Timer Setting Recording SetupDisplay Setup Communication Setup Timer Setting Color Mode Setting Recording SetupRecording Quality Setup Video Pixels ResolutionSpace Group SetupGroup Title Setup Camera AssignmentRecording of the Title Display Thumbnail Display SetupPlayback Mode Setup Shuttle Speed SetupHard Disk End Setup Manual Recording Mode Setting→ Manual with Audio → Manual Without Audio → Event Recording Manual Recording Program Timer Alarm Active Mode Manual RecordingSpecial Day Timer Time Lapse Recording Internal Timer External Program TimerEvent Recording Alarm Active ModeMulti Shot Recording Internal Timer One Shot Recording Internal Timer Emergency Recording Time Lapse Recording Live Sequence Multiplexer SetupSequence Setup Multiscreen Monitor Live Sequence Pattern SettingQuad Shift Setting Quad Pattern SetupSequence Timing Setting Live Sequence Pattern Setting Sequence Setup Spot MonitorGroup Multi Sequence Setting Auto Skip SettingPower on Setting Multiscreen Monitor Power on Setting Spot MonitorSequence Timing Setting Secret View Setting Alarm Output Setting Alarm SetupAlarm Port Setting Alarm Auto Reset SettingAlarm Buzzer Setting Video Loss Alarm SettingVideo Motion Detector Setting Alarm Mode on the Spot Monitor Alarm Mode on the Multiscreen MonitorClock Display Display SetupCamera Title Setup Display Setting Multiscreen MonitorStatus Display Title Display Setting Spot MonitorAlarm Display Setting Title DisplayTitle Display Position Setting Clock and Status Display Position SettingBaud Rate Communication SetupPS Data Setup Unit Address SettingStop Bit Alarm DataInput Camera Number Setup Parity CheckRS-232C Setup Network Setup SET Time System SetupClock Setup Time Adjustment SettingAuto Button Locked Setting Password Lock SettingBuzzer Setting User Defined SettingDisk Space Indicator Disk ManagementDisk Information System Information Error ReportDVD Drive Setup Alarm Recording BackupDVD Format Emergency Recording Backup DVD Disk End SetupDisk Space Display Operating Procedures Single Spot Live Controlling the Video Input and MonitorsControlling the Spot Monitor Selecting the Spot MonitorControlling the Multiscreen Monitor Selecting the Multiscreen MonitorZooming Single Spot Live Group Single Sequence Live Multiscreen Spot Live Multiscreen SelectAll Input Display with Quad Shift Off All Input Display with Quad Shift On Group Display Multi Sequence LiveGroup Multi Sequence Multi Group setting Quad settingAlarm Control Function Alarm InputAlarm Operation Auto Reset Alarm ResetAlarm Suspension Manual ResetManual Recording Internal Timer RecordingPower-on Time Lapse Recording RecordingAlarm Recording Alarm Recording for Manual and Power-on RecordingSet to ALM-ONLY Alarm Recording for Internal Timer Modes Set to ALM-MULTITime Lapse Recording Emergency Recording Forward or Backward search PlaybackBasic Playback StopRecord List Alarm jump searchSearch Record Function Jump searchAlarm Log Search DisplayTime & Date Search Display on the Monitor Single and Multiscreen Spot PlaybackZooming Single Spot Playback REC Preview Displaying Camera and Playback ImageJogDial Backup FunctionDisplay Auto Erase Function Data Erase FunctionManual Erase Function To release this function, follow the procedure below Button Locked FunctionLock Playback of Backup Data Input and Output SpecificationsStandard Accessory GeneralPanasonic Canada Inc Addendum