Panasonic WJ-HD500A manual Formatting the Hard Disk

Page 28

FORMATTING THE HARD DISK

The Hard Disk requires formatting before it can be used for storing images, as shown below.

•When the Hard Disk in the Disk Recorder is replaced. (Disk formatting is required for the replaced Hard Disk.)

•When the optional extension units are operated for the first time after installation.

(Disk formatting is required for the Hard Disk in the Extension Unit.)

Notes:

•Remember that by formatting the hard disk all previ- ously recorded data on the disk will be erased.

•If the Disk Recorder is set up with the mirroring function, the replaced Hard Disk is automatically copying the data from the other disk of the pair after the disk was formatted.

Copying data will take about two hours for a disk with a capacity of 30 GB.

Follow the procedures described below to format the Hard Disk in the unit.

1.Power up the Disk Recorder by pressing the POWER switch.

2.The Disk Recorder will run through a series of instruc- tions for the system on the Multiscreen Monitor.

The display as shown below appears on the monitor, then the DISK MENU shown below will be displayed after five seconds.

[ SYSTEM CHECK ]

YOU HAVE TO CONFIGURE DISKS

PLEASE WAIT

DISK MENU

 

 

 

MAIN 1:¢¢GB 2:¢¢GB

 

 

EXT5 1:¢¢GB 2:¢¢GB 3:¢¢GB

4:¢¢GB

EXT4

1:ADD

2:ADD

3:ADD

4:ADD

EXT3

1:-

2:-

3:-

4:-

EXT2

1:-

2:-

3:-

4:-

EXT1

1:-

2:-

3:-

4:-

EXT0

1:-

2:-

3:-

4:-

EXT DVD:-

REMOVE FORMAT

RESTART

SELECT ITEM AND PRESS [SET] KEY

3.Move the cursor to FORMAT in the menu by pressing the A or B button, then press the SET button.

The FORMAT MENU shown below appears on the mon- itor screen.

FORMAT MENU

 

 

 

MAIN 1:¢¢GB 2:¢¢GB

 

 

EXT5 1:¢¢GB 2:¢¢GB

3:¢¢GB 4:¢¢GB

EXT4

1:ADD

2:ADD

3:ADD

4:ADD

EXT3

1:-

2:-

3:-

4:-

EXT2

1:-

2:-

3:-

4:-

EXT1

1:-

2:-

3:-

4:-

EXT0

1:-

2:-

3:-

4:-

EXT DVD:-

PASSWORDB-----

4.Select the ALL password (5-digit) by pressing the Numeric buttons (1 - 10).

Refer to the password setup in the SYSTEM SETUP menu for further details.

The factory default setting is 12345.

•To select "0" for numeric input, press the numeric 10 button.

•Entering an input will automatically check the pass- word.

If the password is not correct, "PASSWORD ERROR!" is displayed on the monitor screen and the display returns to step 2.

To enter the password again, repeat procedures 3 and 4.

•To quit entering the password, press the SETUP/ ESC button.

5.If the password is correct, the instructions shown below appear in the lower-left corner of the menu.

FORMAT MENU

 

 

 

MAIN 1:¢¢GB 2:¢¢GB

 

 

EXT5 1:¢¢GB 2:¢¢GB

3:¢¢GB 4:¢¢GB

EXT4

1:ADD

2:ADD

3:ADD

4:ADD

EXT3

1:-

2:-

3:-

4:-

EXT2

1:-

2:-

3:-

4:-

EXT1

1:-

2:-

3:-

4:-

EXT0

1:-

2:-

3:-

4:-

EXT DVD:-

1DISK ALL ALL MIRROR RESTART

SELECT ITEM AND PRESS [SET] KEY

29

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Operating Instructions English Version Contents Features PrefaceReliable recording of events Easy image searchPrecautions Fully charge up the backup batteryDo not drop metallic parts through slots Do not attempt to disassemble the applianceFront View @4Alarm Search Button Alarm Search @8Setup/Escape Button SETUP/ESC1Numeric Buttons 1 2Set Button SET#0Full Indicator Full #1Hard Disk Drive Indicator HDD$1Multiscreen Output Connector Multiscreen OUT $2Spot Output Connector Spot OUT$7Alarm Port Alarm $9Mode Selector Mode2Gen-lock Output Connector GEN-LOCK OUT 8Power Switch Power ON/OFFWV-CU50 Remote Controller 9Alarm Search Button Alarm Search 1Link Indicator LinkBlinking Pause mode 0JogDial 6Electronic Zoom Button EL-ZOOMInstallation Installing the Optional Hard DiskInstalling the Optional Motion Detector Board Installing the Optional Network Board Mounting into the Rack Connections Basic SystemSystem Expansion Shown below are examples of system connectionsConnection with the Camera Sites Connection with the Remote ControllerConnection with the Monitors Alarm Port Connection AlarmControl Port Connection Connection with the Uninterrupted Power Supply UPS Connection with Control outputSwitch Setting Connection with the Extension UnitsScsi Connection ModeConnection with the DVD Extension Unit Switch SettingsConnection with the DVD Extension Unit without HDD Connection with the DVD Extension Unit with HDD Scsi ID=0 toMode Selector Setting Connection to PSData Compatible EquipmentSerial Port Connection 10/100BASE-T Port ConnectionPreparations Power UP Procedure Formatting the Hard Disk 1DISK Format Formatting the DVD-RAM Disk Mirroring Function To deactivate the mirror function Disk Remove Monitors and Displays Spot and Multiscreen MonitorStatus Display Time DisplayFormat Error or System Status DisplayGroup Display Electronic Zoom DisplayTimer Recorder Hard DiskManual Recorder Emergency RecorderMulti Shot Recording Time Lapse RecordingDynamic Recording is set to OFF One Shot Recording Dynamic Recording is set to ALM-ONLYSetup Procedures Setup Menu Displaying the Setup MenuSetup Timer Setting Recording Setup Programming Menu SetupDisplay Setup Communication Setup Timer Setting Recording Setup Recording Quality SetupVideo Pixels Resolution Color Mode SettingGroup Setup Group Title SetupCamera Assignment SpaceThumbnail Display Setup Playback Mode SetupShuttle Speed Setup Recording of the Title DisplayManual Recording Mode Setting Hard Disk End Setup→ Manual with Audio → Manual Without Audio → Event Recording Manual Recording Alarm Active Mode Manual Recording Program TimerSpecial Day Timer External Program Timer Time Lapse Recording Internal TimerAlarm Active Mode Event RecordingMulti Shot Recording Internal Timer One Shot Recording Internal Timer Emergency Recording Time Lapse Recording Multiplexer Setup Sequence Setup Multiscreen MonitorLive Sequence Pattern Setting Live SequenceQuad Pattern Setup Quad Shift SettingSequence Timing Setting Sequence Setup Spot Monitor Group Multi Sequence SettingAuto Skip Setting Live Sequence Pattern SettingPower on Setting Spot Monitor Power on Setting Multiscreen MonitorSequence Timing Setting Secret View Setting Alarm Setup Alarm Port SettingAlarm Auto Reset Setting Alarm Output SettingVideo Loss Alarm Setting Alarm Buzzer SettingVideo Motion Detector Setting Alarm Mode on the Multiscreen Monitor Alarm Mode on the Spot MonitorDisplay Setup Camera Title SetupDisplay Setting Multiscreen Monitor Clock DisplayTitle Display Setting Spot Monitor Alarm Display SettingTitle Display Status DisplayClock and Status Display Position Setting Title Display Position SettingCommunication Setup PS Data SetupUnit Address Setting Baud RateAlarm Data Input Camera Number SetupParity Check Stop BitRS-232C Setup Network Setup System Setup Clock SetupTime Adjustment Setting SET TimePassword Lock Setting Buzzer SettingUser Defined Setting Auto Button Locked SettingDisk Management Disk Space IndicatorDisk Information Error Report System InformationAlarm Recording Backup DVD Drive SetupDVD Format DVD Disk End Setup Emergency Recording BackupDisk Space Display Operating Procedures Controlling the Video Input and Monitors Controlling the Spot MonitorSelecting the Spot Monitor Single Spot LiveSelecting the Multiscreen Monitor Controlling the Multiscreen MonitorZooming Single Spot Live Group Single Sequence Live Multiscreen Select Multiscreen Spot LiveAll Input Display with Quad Shift Off Multi Sequence Live All Input Display with Quad Shift On Group DisplayMulti Group setting Quad setting Group Multi SequenceAlarm Input Alarm Control FunctionAlarm Operation Alarm Reset Alarm SuspensionManual Reset Auto ResetInternal Timer Recording Power-on Time Lapse RecordingRecording Manual RecordingAlarm Recording for Manual and Power-on Recording Alarm RecordingSet to ALM-ONLY Set to ALM-MULTI Alarm Recording for Internal Timer ModesTime Lapse Recording Emergency Recording Playback Basic PlaybackStop Forward or Backward searchAlarm jump search Search Record FunctionJump search Record ListDisplay Alarm Log SearchTime & Date Search Single and Multiscreen Spot Playback Display on the MonitorZooming Single Spot Playback Displaying Camera and Playback Image REC PreviewBackup Function JogDialDisplay Data Erase Function Auto Erase FunctionManual Erase Function Button Locked Function To release this function, follow the procedure belowLock Playback of Backup Data Specifications Standard AccessoryGeneral Input and OutputPanasonic Canada Inc Addendum
Top Page Image Contents