Panasonic WJ-HD500A manual Alarm Recording for Manual and Power-on Recording, Set to ALM-ONLY

Page 86

Notes:

•When the TIMER parameter is set to EXT in the setup menu for Power-on Recording, the Internal Timer Recording is disabled.

•Make sure to keep the POWER switch on the rear of the Disk Recorder set to ON.

■Alarm Recording

The Disk Recorder activates the recording alarm status within the specified recording mode, when an externally connected alarm sensor is turned on, or when the installed Video Motion Detector (optional) is activated.

The alarm recording mode is determined by the setup in the WJ-HD500 SETUP menu. Described below is an alarm recording mode for each recording mentioned above.

Note: The received alarm is ignored when the Disk Recorder is recording images in the Emergency Recording. (the alarm log is stored in the ERROR REPORT table.)

●Alarm Recording for Manual and Power-on Recording

The Disk Recorder records an alarm status based on the setup made in the MANUAL REC SETUP menu of the WJ-HD500 SETUP menu.

It records the images as shown below in Time Lapse Recording mode with the specified recording rate, quality and duration. The recording pattern varies according to the setting for the Dynamic Recording (DYNAMIC REC) parameter.

•Set to OFF

Records all input images in sequence starting from video input which have activated alarm.

Start

Alarm 2 in

Alarm 3 in

C1

C2

C3

C4

C2

C3

C4

C5

C6

C3

C4

C5

C6

T

Thumbnail

T

Thumbnail

T

Thumbnail

•Set to ALM-PRI

Records the alarm-activated input images preferentially over other video inputs.

Start

Alarm 4 in

Alarm 15 in

C1

C2

C3

C4

C4

C1

C4

C2

C4

C15

C1

C4

C2

T

Thumbnail

T

Thumbnail

T

Thumbnail

•Set to ALM-ONLY

Records the particular images which have activated the alarm.

Start

Alarm 4 in

Alarm 15 in

C1

C2

C3

C4

C4

C4

C4

C4

C4

C15

C15

C15

C15

T

Thumbnail

T

Thumbnail

T

Thumbnail

89

Image 86

Contents Operating Instructions English Version Contents Reliable recording of events FeaturesPreface Easy image searchDo not drop metallic parts through slots PrecautionsFully charge up the backup battery Do not attempt to disassemble the applianceFront View 1Numeric Buttons 1 @4Alarm Search Button Alarm Search@8Setup/Escape Button SETUP/ESC 2Set Button SET$1Multiscreen Output Connector Multiscreen OUT #0Full Indicator Full#1Hard Disk Drive Indicator HDD $2Spot Output Connector Spot OUT2Gen-lock Output Connector GEN-LOCK OUT $7Alarm Port Alarm$9Mode Selector Mode 8Power Switch Power ON/OFFWV-CU50 Remote Controller Blinking Pause mode 0JogDial 9Alarm Search Button Alarm Search1Link Indicator Link 6Electronic Zoom Button EL-ZOOMInstallation Installing the Optional Hard DiskInstalling the Optional Motion Detector Board Installing the Optional Network Board Mounting into the Rack System Expansion ConnectionsBasic System Shown below are examples of system connectionsConnection with the Monitors Connection with the Remote ControllerConnection with the Camera Sites Alarm Port Connection AlarmControl Port Connection Connection with the Uninterrupted Power Supply UPS Connection with Control outputScsi Connection Switch SettingConnection with the Extension Units ModeConnection with the DVD Extension Unit without HDD Switch SettingsConnection with the DVD Extension Unit Connection with the DVD Extension Unit with HDD Scsi ID=0 toMode Selector Setting Connection to PSData Compatible EquipmentSerial Port Connection 10/100BASE-T Port ConnectionPreparations Power UP Procedure Formatting the Hard Disk 1DISK Format Formatting the DVD-RAM Disk Mirroring Function To deactivate the mirror function Disk Remove Status Display Monitors and DisplaysSpot and Multiscreen Monitor Time DisplayGroup Display Format Error orSystem Status Display Electronic Zoom DisplayManual Recorder Timer RecorderHard Disk Emergency RecorderDynamic Recording is set to OFF Time Lapse RecordingMulti Shot Recording One Shot Recording Dynamic Recording is set to ALM-ONLYSetup Procedures Setup Menu Displaying the Setup MenuDisplay Setup Communication Setup Programming Menu SetupSetup Timer Setting Recording Setup Timer Setting Video Pixels Resolution Recording SetupRecording Quality Setup Color Mode SettingCamera Assignment Group SetupGroup Title Setup SpaceShuttle Speed Setup Thumbnail Display SetupPlayback Mode Setup Recording of the Title Display→ Manual with Audio → Manual Without Audio → Hard Disk End SetupManual Recording Mode Setting Event Recording Manual Recording Alarm Active Mode Manual Recording Program TimerSpecial Day Timer External Program Timer Time Lapse Recording Internal TimerAlarm Active Mode Event RecordingMulti Shot Recording Internal Timer One Shot Recording Internal Timer Emergency Recording Time Lapse Recording Live Sequence Pattern Setting Multiplexer SetupSequence Setup Multiscreen Monitor Live SequenceSequence Timing Setting Quad Shift SettingQuad Pattern Setup Auto Skip Setting Sequence Setup Spot MonitorGroup Multi Sequence Setting Live Sequence Pattern SettingSequence Timing Setting Power on Setting Multiscreen MonitorPower on Setting Spot Monitor Secret View Setting Alarm Auto Reset Setting Alarm SetupAlarm Port Setting Alarm Output SettingVideo Motion Detector Setting Alarm Buzzer SettingVideo Loss Alarm Setting Alarm Mode on the Multiscreen Monitor Alarm Mode on the Spot MonitorDisplay Setting Multiscreen Monitor Display SetupCamera Title Setup Clock DisplayTitle Display Title Display Setting Spot MonitorAlarm Display Setting Status DisplayClock and Status Display Position Setting Title Display Position SettingUnit Address Setting Communication SetupPS Data Setup Baud RateParity Check Alarm DataInput Camera Number Setup Stop BitRS-232C Setup Network Setup Time Adjustment Setting System SetupClock Setup SET TimeUser Defined Setting Password Lock SettingBuzzer Setting Auto Button Locked SettingDisk Information Disk Space IndicatorDisk Management Error Report System InformationDVD Format DVD Drive SetupAlarm Recording Backup Disk Space Display Emergency Recording BackupDVD Disk End Setup Operating Procedures Selecting the Spot Monitor Controlling the Video Input and MonitorsControlling the Spot Monitor Single Spot LiveZooming Single Spot Live Controlling the Multiscreen MonitorSelecting the Multiscreen Monitor Group Single Sequence Live All Input Display with Quad Shift Off Multiscreen Spot LiveMultiscreen Select Multi Sequence Live All Input Display with Quad Shift On Group DisplayMulti Group setting Quad setting Group Multi SequenceAlarm Operation Alarm Control FunctionAlarm Input Manual Reset Alarm ResetAlarm Suspension Auto ResetRecording Internal Timer RecordingPower-on Time Lapse Recording Manual RecordingSet to ALM-ONLY Alarm RecordingAlarm Recording for Manual and Power-on Recording Time Lapse Recording Alarm Recording for Internal Timer ModesSet to ALM-MULTI Emergency Recording Stop PlaybackBasic Playback Forward or Backward searchJump search Alarm jump searchSearch Record Function Record ListTime & Date Search Alarm Log SearchDisplay Zooming Single Spot Playback Display on the MonitorSingle and Multiscreen Spot Playback Displaying Camera and Playback Image REC PreviewBackup Function JogDialDisplay Data Erase Function Auto Erase FunctionManual Erase Function Lock To release this function, follow the procedure belowButton Locked Function Playback of Backup Data General SpecificationsStandard Accessory Input and OutputPanasonic Canada Inc Addendum