JVC HRS6960E specifications Other Problems

Page 63

			EN 63

	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
8.	“ “, “” and “$“ on the front	● The loaded cassette has had its record	Remove the cassette and cover the hole
	display panel won’t stop blinking.	safety tab removed.	with adhesive tape, or insert a cassette
			with the record safety tab intact.
		● The end of the tape was reached during	The programme may not have been
		Automatic Satellite Programme	recorded in its entirety. Next time make
		Recording.	sure you have enough time on the tape to
			record the entire programme.

OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1. Whistling or howling is heard from the		● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 54).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			Then perform Auto Set Up again
			( pg. 11).
		● The fully-wired 21-pin SCART cable was	Turn off the recorder once and connect
		not connected between TV and the	the fully-wired 21-pin SCART cable to the
		recorder when Preset Download was	recorder properly, then turn on the
		performed.	recorder again. Then perform Preset
			Download again ( pg. 13).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 63

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Counter can display up to +/ 195959. If Playback or recording time exceeds this limitTape Speed SP/LP/EP pg ON-SCREEN Display Remote Control Operating JVC TVs How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderBefore starting, make sure of the following Auto Set UpTurn on the recorder Select your countryConfirm/Set video channel Perform Auto Set Up12 EN Select the languageSet the video channel to off manually. pg Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or e14 EN Language for the on-screen displayJust Clock Return to the normal screen Access the Main Menu screenAccess the Country Set screen LanguageAttach the Satellite Controller Installing Satellite Controller16 EN Situate the Satellite ControllerTurn on the satellite receiver Setting satellite receivers brand and channelAccess the Sat Control Set screen Select the satellite receiver’s channel for testingVCR Auto Standby Direct Rec TV Auto Power On18 EN NextView LinkBasic Playback Pause during playback 20 ENSlow Motion Picture SearchInstant Review Variable Speed SearchIndex Search Skip SearchManual Tracking 22 ENNext Function Memory Repeat PlaybackStart recording Recording Resume FunctionChoose a programme Set the tape speedInstant Timer Recording ITR 24 ENTape Remaining Time Engage the S-VHS ET mode Super VHS ET S-VHS ETReceiving Stereo and Bilingual Programmes 26 EN PlaybackRecording Enter the Showview number Access the Showview screenAccess the Showview Program screen Before performing the Showview Timer Programming28 EN Set the VPS/PDC modeAccess the Title Edit screen Engage the recorder’s timer modeEnter the programme stop time Express Timer ProgrammingAccess the Programme screen Enter the programme start timeEnter the channel position To Timer-Record Weekly Or Daily Serials30 EN VPS/PDC RecordingEnter the programme mode Before performing the 24 Hour Express Timer ProgrammingSet the programme start/stop time and channel 32 EN Disengage the timer modeCancel or change a programme Return to the timer modeOverlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modify34 EN Select the L-2 Select modeRecording mode Programme RecordingNavigation When inserting a cassette with the record safety tab IntactLoad a recorded cassette 36 ENNavigation Playback Programme Navigation ScreenSelect the programme Edit Programme TitleDelete the tape data 38 ENEntering Character Delete Tape DataCamcorder Edit From a40 EN AnotherOutput/Input Set B Access the Output/Input Set screen Output and L-1 Input Setting42 EN Decoder connectorSimple Connections Connecting To a Satellite ReceiverPerfect Connections 44 ENSet L-2 Select to DECODER. pg Select the input modeConnect the decoder Set the tunerMake connections 46 ENSelect the mode setting Mode SetAccess the Mode Set screen Select the mode48 EN On the remote control, or press 7 on the recorder Entire programme while timer-recording in SP modeFor Example 50 EN Colour System Auto Channel Set Access the Auto Channel Set screenTuner Set 52 ENPerform Auto Channel Set View the Confirmation screenPress OK twice Manual Channel Set 54 ENDelete a Channel When Receiving a Scrambled Broadcast56 EN Set Stations aSet Stations B Station Name TV Station And ID ListAccess the Clock Set screen Clock Set58 EN Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data60 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel SetPower Recording 62 ENOther Problems Playback 64 ENLines VHS Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Scan system66 EN Memo