Heath Zenith 598-1135-08 operating instructions Features, Code Settings

Page 1

Remote Controlled Products

This manual includes operating instructions for a variety of remote controlled products. All products work on the same principle and use the same code setting information. Please read all instructional information and note any specific information pertaining to your particular product.

This manual applies to the following products:

• Transmitters

• Receivers

– Remote Control

– Wall Switch Receiver

– Indoor Wireless Motion Sensor

– Receptacle Receiver

Outdoor Wireless Motion Sensor

Add-A-Switch

Kid’s Remote Control

3-Way Wall Switch

Features

Products are UL/cUL and/or FCC/IC tested and approved.

Operational range of up to 100 feet.

Heath®/Zenith wireless lighting controls are designed to work together. Simply determine which transmitter(s) you would like to have control which receiver(s) and set the code setting to match.

ENGLISH

Code Settings

Note: Most single system installations will not require any change to the code setting. Transmitter(s) and receiver(s) must have the same code and group setting to work together. Switches 1 through 3 set the code. Switch 4 sets the Group (A or B). See page 2 for switch locations.

Example 2 - Code Settings, System 2

Note:When operating more than one system independently of each other, set each system to a different code.There are 8 codes avail- able by changing the settings of switches 1 through 3.

Receiver(s)

Transmitter

Code

Code

Example 1 - Code Settings, System 1

(Factory Setting)

Left Side Controls:

 

 

 

 

 

Right Side Controls:

Controls One Set of

DIM

DIM

Controls One Set of

Group “A” or Group

 

 

 

 

 

Group “A” or Group

“B” Receiver(s)

ON

 

ON

“B” Receiver(s)

 

 

 

 

 

 

 

 

OFF

 

OFF

 

Group “A”

Group Switch

 

(Group “A” Selection Shown)

Example 3 - Code Settings with Single Transmitter

When using a single group transmitter (i.e. Door Transmitter, Add-A- Switch, Remote Motion Sensor) the code and group settings must match receiver(s) for the system to function properly.

 

Transmitter(s)/

Transmitter(s)/

 

Receiver(s) Code

Receiver(s) Code

 

Group “A”

Group “B”

(

– Indicates Position of Switch)

 

Receiver(s)

Remote Motion

Code

Sensor Code

Group “A”

Group “A”

Note: This setting will work independently of examples 1 and 2 because the code setting is different.

Note:The code can also be changed to reduce interference problems from other wireless products (i.e. wireless phones, garage door open- ers, etc.). See Troubleshooting Guide for more information.

© 2007 HeathCo LLC

598-1135-08

Image 1
Contents Code Settings FeaturesExample 2 Code Settings, System Example 1 Code Settings, SystemRemote Control Indoor Wireless Motion Sensor Code Switch LocationsAdd-A-Switch Kid’s Remote Control Wall Switch Receiver Receptacle ReceiverRear View of Remote Control Remote ControlOptional Car Visor Clip Included Function ControlsSelect Night or 24 Hour Mode Indoor and outdoor Wireless Motion SensorInstalling Batteries Battery CompartmentInstalling Outdoor Motion Sensor Installing Indoor Motion Sensor Directly To WallCheck Operation and Adjustment Outdoor Motion Sensor Coverage Area Adjusting Outdoor Motion Sensor CoverageIndoor and Outdoor Motion Sensor Sensitivity Motion Sensor ControlsKid’s Remote Control Add-A-SwitchInstallation Battery ReplacementRemoving Tab In Battery Chamber WAY Wall Switch TransmitterInside of Remote Control Bulb Replacement ImportantInformationRegarding3-WaySwitchInstallations Wall Switch ReceiverInstalling Wall Switch Receiver Receiver InformationReceptacle Screw Wall Plate Ground Wire Bare or Green Testing and OperationInstalling Receptacle Receiver Receptacle ReceiverTechnical Service Troubleshooting GuideNo Service Parts Available for this Product Regulatory InformationTWO Year Limited Warranty Calibraciones DEL Código CaracteristicasEjemplo 1 Calibraciones del código, sistema Ejemplo 2 Calibraciones del código, sistemaTapa de Acceso Ubicaciones DE LOS Interruptores DE Circuito ImpresoInterruptores de circuito impreso De circuito On impreso Receptor de pared con interruptorPresilla opcional del visor del carro incluida Control remotoRetiro de la presilla del visor Vista posterior Instalación de las baterías Seleccione modo nocturno o modo de 24 horasControl Características No se requiere cableadoMovimiento Zócalo de la consola TuercaFijación del detector de movimiento directamente a la pared Revisión de la operación y de la regulación Instalación del detector de movimiento para uso ExteriorDetector de movimiento para uso exterior Los controles Instalación del detector de movimientoControles del detector de movimiento Instalación Interruptor a añadibleOperación Reemplazo de la bateríaTransmisor de pared con conmutador tridireccional Control Remoto Para NiñosInterior del control remoto Retiro de la puerta de accesoTransmisor Conductores retornoTierra del conmutador De paredReceptor DE Pared CON Interruptor Información DEL ReceptorInstalación Reemplazo de la bombillaInstalación del receptor de pared con interruptor Receptor CON TomacorrienteInstalación del receptor con tomacorriente Servicio Técnico Guía de Análisis de AveríasPrueba y operación No hay piezas de servicio disponibles para este productoGarantía Limitada a 2 Años Información RegulatoriaRéglage DES Codes CaractéristiquesExemple 1 Réglage des codes, System Exemple 2 Réglage des codes, systèmeTélécommande Détecteur de mouvements sans fil Intérieur Emplacement DES MICRO-INTERRUPTEURSDétecteur de mouvements sans fil Extérieur MicroCommandes des fonctions TélécommandeVue arrière de la télécommande Pince de pare-soleil dautomobile facultative CompriseInstallation des piles Sélection du mode de nuit ou du mode 24 heuresDétecteurs DE Mouvement Sans FIL Intérieurs ET Extérieurs Compartiment des pilesImportant Serrer à la main seulement, ne pas trop serrer Retirez les pilesInstallation du détecteur de mouvement Installation du détecteur de mouvements extérieurDétecteur de mouvements extérieur Les commandes « Commandes du détecteur de mouvementZone de couverture du détecteur de mouvements extérieur Zone de couverture du détecteur de mouvements intérieurMouvementMouvement Interrupteur d’appoint Remplacement de la pileFonctionnement Intérieur de la télécommande Télécommande Pour EnfantÉmetteur Dinterrupteur Mural À Trois Voies Retrait de la porte d’accèsFils de connexion Informations SUR LE Récepteur Remplacement de l’ampouleInterrupteur Récepteur Mural Puissance nominaleInstallation de la prise réceptrice Installation de l’interrupteur transmetteur muralPrise réceptrice Essai et fonctionnement Guide DE DépannageRenseignements de règlements Service TechniqueGarantie Limitée DE 2 ANS Aucune pièce de rechange n’est disponible pour ce produit598-1135-08 Is nçaa fr 598-1135-08

598-1135-08 specifications

The Heath Zenith 598-1135-08 is a state-of-the-art motion-activated floodlight designed to enhance security and visibility around your home or property. With its durable construction and advanced technological features, this floodlight offers an efficient solution for outdoor lighting needs.

One of the key aspects of the Heath Zenith 598-1135-08 is its reliable motion detection technology. Featuring a high-performance sensor, this floodlight can detect movement within a wide range, typically up to 240 degrees. This expansive field of view ensures that any activity within its range is promptly detected, providing an added layer of security for your belongings and family.

The floodlight also boasts an impressive illumination capacity. Equipped with powerful LED bulbs, it delivers bright, energy-efficient lighting that can easily illuminate large outdoor areas. The LED technology not only ensures a longer lifespan for the bulbs but also significantly reduces energy consumption, making it an environmentally friendly choice.

Another notable characteristic is the adjustable settings available with the Heath Zenith 598-1135-08. Users can easily customize the sensitivity of the motion sensor, allowing it to adapt to specific needs such as varying outdoor conditions or traffic levels. Additionally, the floodlight offers a time delay feature, permitting the light to stay on for a designated period after motion is detected, providing extra convenience.

The design of the Heath Zenith 598-1135-08 combines functionality with aesthetic appeal. The sleek, modern look of the floodlight makes it suitable for various types of homes and outdoor settings. Moreover, its weather-resistant construction ensures that it can withstand harsh weather conditions, maintaining its performance throughout the seasons.

Installation of the Heath Zenith 598-1135-08 is straightforward, making it accessible for homeowners looking to enhance their outdoor lighting without professional assistance. The adjustable head allows for directional lighting, ensuring that specific areas can be spotlighted as needed.

Overall, the Heath Zenith 598-1135-08 is an exemplary choice for homeowners seeking robust, energy-efficient outdoor lighting solutions. Its combination of advanced motion detection technology, customizable settings, and durable design makes it a valuable addition for increased security and visibility around any property.