Heath Zenith 598-1135-08 operating instructions Installing Indoor Motion Sensor Directly To Wall

Page 5

(Note:You should hear a snap). Aim sensor toward area where detection is desired. Tighten clamp screw.

Mounting

 

Mounting Screw

Nut

 

Bracket Socket

 

Mounting

 

 

Bracket

 

 

Clamp

 

 

Screw

 

 

Swivel Ball Mount

 

Battery Compartment

Sensor

Cover

 

 

Attaching Indoor Motion Sensor to Mounting Bracket

Installing Indoor Motion Sensor Directly To Wall

Note: Mount the indoor motion sensor so that it is approximately

between waist and shoulder level above the floor (Example: Level with light switch, under counter top, etc.).

1.Determine the best mounting position of the sensor for the coverage desired. Remove the batteries.

2.Place indoor motion sensor against surface to be mounted on. Using two of the holes on the rear of the battery compartment, mark hole locations with pencil or center punch.

3.Using a 2.5 mm (0.1") drill bit, drill two pilot holes for mounting screws. If not mounting directly to wood or wood stud, drill 5 mm (0.2") pilot holes and use the included wall anchors.

4.Attach indoor motion sensor to a sturdy object (i.e. wall, cabinet, post, etc.) using two screws provided. Make sure unit has an unobstructed view.

IMPORTANT: Hand tighten only - do not overtighten.

Motion

Counter

Top

Sensor

 

Mounting

Screw

Attaching Indoor Motion Sensor Directly to Wall

Installing Outdoor Motion Sensor

1. Installsensormountingbracketwheremotiondetectionisdesired.

 

Attach sensor mounting bracket to a sturdy object (i.e. tree, post,

 

house, etc.) using two screws provided. Make sure unit has an

 

unobstructed view. Note: Attach mounting bracket vertically if

 

connecting to a curved surface such as a post.

ENGLISH

2. Install motion sensor to mounting bracket.Using a Philips-head

screwdriver, loosen the clamp screw on the mounting bracket.

Insert swivel ball mount on sensor into mounting bracket socket

 

(Note:You should hear a snap). Aim sensor toward area where

 

detection is desired. Tighten clamp screw.

 

IMPORTANT: The sensor must be mounted with the bottom cover

 

facing down in order to maintain water tightness.

 

Mounting

Mounting Bracket

 

 

 

Bracket Socket

Mounting Screw

 

Clamp

Nut

 

 

 

Screw

 

 

Swivel Ball Mount

 

 

Sensor

 

 

Installing Motion Sensor

Check Operation and Adjustment

Note: When first turned on or when switching modes wait 30 seconds.

Locate the RANGE control and ON-TIME control on the motion sensor:

•Indoor Motion Sensor - The RANGE control and ON-TIME control are located inside the battery compartment on the front of the sensor. To set the RANGE or ON-TIME control, remove battery compartment cover by sliding the cover down.

•Outdoor Motion Sensor - The RANGE control and ON-TIME control are located on the bottom of the sensor. Using your fingernails or a small, flat-head screwdriver, gently pry the cover until it opens.

1.Check Operation. Set the ON-TIME control to TEST mode. Walk in front of sensor unit. The LED indicator light should flash when motion is detected (see illustration, page 6, for location of LED light).

2.Adjust Sensor. Turn the RANGE control to the mid position and ON-TIME control to theTEST position.Walk through coverage area notingwhereyouarewhentheLEDbeginstoflash.Loosentheclamp screw and move the sensor to change the coverage area. Tighten clamp screw when finished. Do not overtighten clamp screw.

Continued

598-1135-08

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Code Settings FeaturesExample 2 Code Settings, System Example 1 Code Settings, SystemRemote Control Indoor Wireless Motion Sensor Code Switch LocationsAdd-A-Switch Kid’s Remote Control Wall Switch Receiver Receptacle ReceiverRear View of Remote Control Remote ControlOptional Car Visor Clip Included Function ControlsSelect Night or 24 Hour Mode Indoor and outdoor Wireless Motion SensorInstalling Batteries Battery CompartmentCheck Operation and Adjustment Installing Indoor Motion Sensor Directly To WallInstalling Outdoor Motion Sensor Outdoor Motion Sensor Coverage Area Adjusting Outdoor Motion Sensor CoverageIndoor and Outdoor Motion Sensor Sensitivity Motion Sensor ControlsKid’s Remote Control Add-A-SwitchInstallation Battery ReplacementInside of Remote Control WAY Wall Switch TransmitterRemoving Tab In Battery Chamber Bulb Replacement ImportantInformationRegarding3-WaySwitchInstallations Wall Switch ReceiverInstalling Wall Switch Receiver Receiver InformationReceptacle Screw Wall Plate Ground Wire Bare or Green Testing and OperationInstalling Receptacle Receiver Receptacle ReceiverTechnical Service Troubleshooting GuideNo Service Parts Available for this Product Regulatory InformationTWO Year Limited Warranty Calibraciones DEL Código CaracteristicasEjemplo 1 Calibraciones del código, sistema Ejemplo 2 Calibraciones del código, sistemaTapa de Acceso Ubicaciones DE LOS Interruptores DE Circuito ImpresoInterruptores de circuito impreso De circuito On impreso Receptor de pared con interruptorRetiro de la presilla del visor Vista posterior Control remotoPresilla opcional del visor del carro incluida Instalación de las baterías Seleccione modo nocturno o modo de 24 horasControl Características No se requiere cableadoFijación del detector de movimiento directamente a la pared Zócalo de la consola TuercaMovimiento Revisión de la operación y de la regulación Instalación del detector de movimiento para uso ExteriorDetector de movimiento para uso exterior Los controles Instalación del detector de movimientoControles del detector de movimiento Instalación Interruptor a añadibleOperación Reemplazo de la bateríaTransmisor de pared con conmutador tridireccional Control Remoto Para NiñosInterior del control remoto Retiro de la puerta de accesoTransmisor Conductores retornoTierra del conmutador De paredReceptor DE Pared CON Interruptor Información DEL ReceptorInstalación Reemplazo de la bombillaInstalación del receptor con tomacorriente Receptor CON TomacorrienteInstalación del receptor de pared con interruptor Servicio Técnico Guía de Análisis de AveríasPrueba y operación No hay piezas de servicio disponibles para este productoGarantía Limitada a 2 Años Información RegulatoriaRéglage DES Codes CaractéristiquesExemple 1 Réglage des codes, System Exemple 2 Réglage des codes, systèmeTélécommande Détecteur de mouvements sans fil Intérieur Emplacement DES MICRO-INTERRUPTEURSDétecteur de mouvements sans fil Extérieur MicroCommandes des fonctions TélécommandeVue arrière de la télécommande Pince de pare-soleil dautomobile facultative CompriseInstallation des piles Sélection du mode de nuit ou du mode 24 heuresDétecteurs DE Mouvement Sans FIL Intérieurs ET Extérieurs Compartiment des pilesImportant Serrer à la main seulement, ne pas trop serrer Retirez les pilesInstallation du détecteur de mouvement Installation du détecteur de mouvements extérieurDétecteur de mouvements extérieur Les commandes « Commandes du détecteur de mouvementMouvementMouvement Zone de couverture du détecteur de mouvements intérieurZone de couverture du détecteur de mouvements extérieur Fonctionnement Remplacement de la pileInterrupteur d’appoint Intérieur de la télécommande Télécommande Pour EnfantÉmetteur Dinterrupteur Mural À Trois Voies Retrait de la porte d’accèsFils de connexion Informations SUR LE Récepteur Remplacement de l’ampouleInterrupteur Récepteur Mural Puissance nominalePrise réceptrice Installation de l’interrupteur transmetteur muralInstallation de la prise réceptrice Essai et fonctionnement Guide DE DépannageRenseignements de règlements Service TechniqueGarantie Limitée DE 2 ANS Aucune pièce de rechange n’est disponible pour ce produit598-1135-08 Is nçaa fr 598-1135-08

598-1135-08 specifications

The Heath Zenith 598-1135-08 is a state-of-the-art motion-activated floodlight designed to enhance security and visibility around your home or property. With its durable construction and advanced technological features, this floodlight offers an efficient solution for outdoor lighting needs.

One of the key aspects of the Heath Zenith 598-1135-08 is its reliable motion detection technology. Featuring a high-performance sensor, this floodlight can detect movement within a wide range, typically up to 240 degrees. This expansive field of view ensures that any activity within its range is promptly detected, providing an added layer of security for your belongings and family.

The floodlight also boasts an impressive illumination capacity. Equipped with powerful LED bulbs, it delivers bright, energy-efficient lighting that can easily illuminate large outdoor areas. The LED technology not only ensures a longer lifespan for the bulbs but also significantly reduces energy consumption, making it an environmentally friendly choice.

Another notable characteristic is the adjustable settings available with the Heath Zenith 598-1135-08. Users can easily customize the sensitivity of the motion sensor, allowing it to adapt to specific needs such as varying outdoor conditions or traffic levels. Additionally, the floodlight offers a time delay feature, permitting the light to stay on for a designated period after motion is detected, providing extra convenience.

The design of the Heath Zenith 598-1135-08 combines functionality with aesthetic appeal. The sleek, modern look of the floodlight makes it suitable for various types of homes and outdoor settings. Moreover, its weather-resistant construction ensures that it can withstand harsh weather conditions, maintaining its performance throughout the seasons.

Installation of the Heath Zenith 598-1135-08 is straightforward, making it accessible for homeowners looking to enhance their outdoor lighting without professional assistance. The adjustable head allows for directional lighting, ensuring that specific areas can be spotlighted as needed.

Overall, the Heath Zenith 598-1135-08 is an exemplary choice for homeowners seeking robust, energy-efficient outdoor lighting solutions. Its combination of advanced motion detection technology, customizable settings, and durable design makes it a valuable addition for increased security and visibility around any property.
Top Page Image Contents