Bulb Replacement

9.Position the wall switch transmitter in the junction box with the DIM button located to the right. Use the two wall switch screws (long) supplied to mount the transmitter to the junction box (see Figure 3). Push excess wiring into junction box while you do this, bending the wires to fit if necessary.

10.Mount the wall plate to the wall switch transmitter with the screws (short) provided.

11.To install the wall switch receiver, repeat steps 5 through 10 above.Note: Route antenna between the bottom of the junction box and the wall. Feed antenna into wall cavity while placing wall switch into junction box.

IMPORTANT: Label wires on existing 3-way switch according to the diagram in Figure 1. Refer to Figure 2 below when con- necting wall switch receiver wires to existing wires.

12.Turn on the power to the light switch circuit.Do this at your circuit breaker or fuse box. Note: If the light turns on immediately and remains on, reverse the travel wire connections on one of the switches.

	Green (or Bare) Ground Wire		Red Wire
Green Ground Wire From Switch			Red Wire
Green Ground Wire From Switch			(Typical)
	ON/OFF	Wall
Wall Switch	ON/OFF	Switch
Wall Switch	Button	Switch
Screw	Button
Screw
			Wall

Junction

Box

Black Wire

	Wall	DIM
	Plate	DIM
	Plate	Button
	Screw	Button
	Screw
		Power
		Disconnect

ENGLISH

TO HOT

OR LIGHT

BLACK

Transmitter

Travel Wires

2 RED

3 BLACK

TO HOT

OR LIGHT

BLACK

Receiver

Wall Plate	Switch

Figure 3 - Installing 3-Way Wall Switch

(Transmitter Shown)

Operation

1.	Verify the power disconnect switch on the transmitter and
	receiver is in the ON (right side) position.
2.	Push the ON (top) button and release. The light should turn on
	full bright. Note: If you are controlling a lamp, make sure it is

DIM

GREEN (Ground)

Figure 2 - Wiring 3-Way Wall Switch

	connected to the switched outlet and the lamp is switched on.
3.	Push the OFF (bottom) button and release. The light should
	turn off.
4.	Push the DIM button and release. The light should turn on at
	50% brightness (or last setting). Note: Receiver remembers
	the last DIM setting used. To recall last DIM setting, push and
	release the DIM button.
5.	Continue to press the DIM button until the desired dim level is
	reached. Note: There are 5 DIM settings ranging from 15% to
	90% brightness.

Note: The DIM setting defaults to 50% in the event of a power failure.

Important: Wait 1 to 2 seconds after you press a transmitter button before you press it again to allow the transmission to be completed.

Note: If light does not turn on or intermittently turns on and off when transmitter buttons are pushed, see Troubleshooting Guide.

Movethepowerdisconnectswitchonthetransmitterandreceivertothe OFF (left side) position. Replace bulb(s). Note:The power disconnect switch on the transmitter prevents the unit from sending any signals to the receiver.The power disconnect switch on the receiver prevents it from applying power to the load that it controls.

598-1135-08

598-1135-08 specifications

The Heath Zenith 598-1135-08 is a state-of-the-art motion-activated floodlight designed to enhance security and visibility around your home or property. With its durable construction and advanced technological features, this floodlight offers an efficient solution for outdoor lighting needs.

One of the key aspects of the Heath Zenith 598-1135-08 is its reliable motion detection technology. Featuring a high-performance sensor, this floodlight can detect movement within a wide range, typically up to 240 degrees. This expansive field of view ensures that any activity within its range is promptly detected, providing an added layer of security for your belongings and family.

The floodlight also boasts an impressive illumination capacity. Equipped with powerful LED bulbs, it delivers bright, energy-efficient lighting that can easily illuminate large outdoor areas. The LED technology not only ensures a longer lifespan for the bulbs but also significantly reduces energy consumption, making it an environmentally friendly choice.

Another notable characteristic is the adjustable settings available with the Heath Zenith 598-1135-08. Users can easily customize the sensitivity of the motion sensor, allowing it to adapt to specific needs such as varying outdoor conditions or traffic levels. Additionally, the floodlight offers a time delay feature, permitting the light to stay on for a designated period after motion is detected, providing extra convenience.

The design of the Heath Zenith 598-1135-08 combines functionality with aesthetic appeal. The sleek, modern look of the floodlight makes it suitable for various types of homes and outdoor settings. Moreover, its weather-resistant construction ensures that it can withstand harsh weather conditions, maintaining its performance throughout the seasons.

Installation of the Heath Zenith 598-1135-08 is straightforward, making it accessible for homeowners looking to enhance their outdoor lighting without professional assistance. The adjustable head allows for directional lighting, ensuring that specific areas can be spotlighted as needed.

Overall, the Heath Zenith 598-1135-08 is an exemplary choice for homeowners seeking robust, energy-efficient outdoor lighting solutions. Its combination of advanced motion detection technology, customizable settings, and durable design makes it a valuable addition for increased security and visibility around any property.