Sterling Plumbing scc2 specifications Enabling and Disabling Stations and Pumps

Page 35

Enter the four-digit password (including any leading zeros). For example, if the password is 1, enter 0001.

Each digit appears as an “X” as you touch it. When you touch the fourth digit, the controller carries out your request. For example, it enables or disables the requested pump or station, or it goes to the “Station Operator” screen. If you did not enter the correct password, the controller erases the entry. You can then try again. To give up, touch Return.

Note: If you have lost the password(s), contact us for assistance.

Once you have logged on, the password remains active until you log off or the password expires. (Setup personnel at your facility control the number of minutes before the password expires.) While the password is active, you can continue to carry out password-protected tasks without reentering the password. If the timer expires, the controller goes to the “Station Status” screen and you must reenter the password to continue working.

When you have finished any tasks that require the password, you should log off. (If you forget to do this, the controller will log you off when the password expires.) To log off, complete the following steps:

1.Go to the “Menu” screen by touching Menu from any other screen.

2.Touch Log Off Password. The “Station Status” screen opens.

Enabling and Disabling Stations and Pumps

When a station or pump is disabled, the controller makes no attempt to use it and ignores any alarms that occur for it. Disabling a station or pump at the controller’s screen is similar to bypassing a station with its bypass switch. Enabling a station or pump makes it available for use.

Note: For a station to be available for the system, it must be enabled at the controller’s screen and its bypass switch must be in the “0” position.

To enable or disable a station (or pump), complete the following steps:

1.Go to the “Station Status” (or “Pump Status”) screen, if needed. To reach this screen from any other screen, touch Menu and then Stations (or Pumps).

Each disabled station (or pump) has an icon with a status of “offline” (black with a gray outline). All other statuses are enabled statuses.

2.Touch the icon for the station (or pump) briefly. The station (or pump) switches to the new state, as indicated by the color of its icon.

Note: If the “Station Operator” (or “Pump Setup”) screen appears when you touch the icon, then you have kept your finger on the screen too long. Touch Stations (or Pumps) to return to the “Status” screen and try again. If you find it difficult to touch the icon briefly enough, ask the setup personnel at your facility to lengthen the touch switch delay.

Hopper Loaders with/without Sight Glasses

30

Page 34 Page 36
Image 35
Page 34 Page 36
Contents SCC 2-Pump 20-Station Controllers Parts and Service Department Shipping Information Credit Returns Warranty ReturnsTable of Contents Safety Restoring a LOST/CORRUPT PROGRAM...380 Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves Controller Safety TagsFail Safe Operation Safety Devices and InterlocksSafety Circuit Standards Safety Device Lock-OutsOperator Responsibility ResponsibilityGeneral Responsibility Reporting a Safety Defect Maintenance ResponsibilityGeneral Description Standard FeaturesFunctional Description Models Covered in This ManualController Features Optional FeaturesMounting the Control Panel InstallationUncrating Pump 20 Station Controller with 6 Display Located on the side of the controller box Controller Identification Serial Number TagElectrical Connections Making Control Panel Power Drop Wiring ConnectionsConnecting the Control Panel to Vacuum Hoppers Connecting the Control Panel to the Pump PackageSet-up Setting the Number of Stations and the Number of PumpsMenu Screen System Setup Screen Setting Up Alarm DurationSetting Up Touch Switch Delay Setting Up Pump StagingSetting Up a Single Station Setting Up StationsCopying Settings from One Station to Others Station Setup ScreenStation Copy Screen Setting Up a Single Pump Setting Up PumpsCopying Settings from One Pump to the Other Pump Setup ScreenPump Copy Screen Operator Password Finishing Setup Setting Up PasswordsSetup Password Page Initial Startup Reviewing Station Status OperationOverview Basic TasksPump Status Screen During Operation Reviewing Pump StatusLogging On and Logging Off Password Entry ScreenEnabling and Disabling Stations and Pumps Starting and Stopping the System Reviewing and Adjusting Basic Station SettingsNavigating Among the Station Operator Screens Adjusting Convey Time and Dump DelayActivating and Stopping Priority Convey for a Station Adjusting Advanced SettingsReviewing and Resetting a Pump Hour Meter Transferring Stations to a Standby Pump Transfer To Standby Pump Screen Reviewing Alarms AlarmsStandby Pump Errors Silencing Alarms Alarm Log ScreenPLC Memory Module Corrective MaintenanceRestoring a Lost or Corrupt Program Page Station Setup Factory Presets Configurable Settings/DefaultsPump 20-Station Controllers Configurable Settings/Defaults Idle Time Options Pump Setup Factory PresetsGeneral Troubleshooting TroubleshootingSystem Alarms Station AlarmsPump Alarms Appendix WarrantyDrawings and Diagrams DC Voltage Spare Parts ListAC Voltage Sales Department Service DepartmentTechnical Assistance Contact Information Parts Department
Top Page Image Contents