Invacare Adjustable ASBA Seat Adjusting the Height of the Manual Center Mount Footrest

Page 19

SECTION 5—CENTER MOUNT FOOTRESTS

Adjusting the Height of the Manual Center Mount Footrest

Chairs built before 12/01/2008

WARNING

After adjusting the center mount footrest, minimum ground clearance for the footrest in the driving position is three inches. If the center mount footrest is in the retracted position and the wheelchair is not moving, the footrest must maintain a minimum of one inch ground clearance - otherwise personal injury and damage may result.

NOTE: For this procedure, refer to FIGURE 5.2.

1.Remove the two mounting screws that secure the footrest extension tube to the extension tube housing.

2.Adjust the footrest extension tube to the desired height.

3.Align the mounting holes on the extension tube housing with the mounting holes on the footrest extension tube.

4.Reinstall the two mounting screws to secure the footrest extension tube to the extension tube housing. Securely tighten.

5.Repeat STEPS 1‐3 for the other extension tube.

	Seat Frame
	Release Lever
	Extension Tube
Mounting Holes	Housing
Mounting Holes
Mounting Screws
Mounting Holes	Footrest
	Extension Tube

FIGURE 5.2 Adjusting the Height of the Manual Center Mount Footrest -

Chairs built before 12/01/2008

Part No 1143238

19

Adjustable ASBA Seat

Image 19

Contents Adjustable Asba Seat Reference Documents Useful TermsTable of Contents Arms Adult Seats Junior Seats Special Notes Signal Word MeaningSpecial Notes All Wheelchairs Label LocationsAll Wheelchairs with Trro Wheelchairs without Trro Typical Product Parameters Adjustable Asba SeatGeneral Guidelines Repair or Service InformationOperation Information Tire Pressure Weight LimitationPinch Points SAFETY/HANDLING of WheelchairsEMI Information EMI Information Safety Inspection Checklist Safety INSPECTION/ TroubleshootingTroubleshooting Center Mount Footrests Installing Removing/Installing the Manual Center Mount FootrestRemoving Chairs built before 12/01/2008 Adjusting the Height of the Manual Center Mount FootrestChairs built after 12/01/2008 Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Angle of the Manual Center Mount FootrestAdjusting the Footplate Angle Chairs built before 12/01/2008 Adjusting the Footplate AngleAdjusting the Tension of the Flip Up Footplate Front Riggings Installing/Removing FootrestsPH904A, PHAL4A, 70 and PW93 Taper Adjusting the Footrest HeightPH904A and PHAL4A Front Riggings PW93 Adjusting the Footrest Height PW93Raising/Lowering Elevating Front Riggings Replacing Heel LoopsAdjusting/Replacing Telescoping Front Rigging Support Adjusting/Replacing Telescoping Front Rigging SupportInstalling Adjustable Angle Flip-up Footplates Installing Adjustable Angle Flip-up Footplate HingePerpendicular and/or Inversion/Eversion Adjustment Adjusting Adjustable Angle Flip-Up FootplatesDepth Adjustment Angle AdjustmentComposite Replacing Composite/Articulating Footplate Heel Loop14 Installing/Removing Elevating Legrests Installing/Removing Elevating LegrestsRaising/Lowering Elevating Legrests Adjusting CalfpadsInstalling/Removing the Power Elevating Legrests Power Elevating LegrestsInstalling the Power Elevating Legrests Removing the Power Elevating Legrests Adjusting the Power Elevating LegrestsAdjusting the Footplate Adjusting the Footplate Depth Adjusting the Footplate Angle Adjusting the Calf Pad Width Adjusting the Calf PadAdjusting the Calf Pad Height Adjusting the Length for Power LegrestRemoving/Installing the Power Elevating Legrest Harness Seat frame for clarity Removing/Installing the Power Elevating Legrest ActuatorRight power Arms Installing/Removing Flip Back ArmrestsPositioning Flip Back Armrests for Use Adjusting Flip Back ArmrestsAdjusting Positioning Flip Back Armrests for User TransferInstalling/Removing the Cantilever Arms Installing/Removing the Cantilever ArmsAdjusting the Height of the Cantilever Arms Adjusting the Height of the Cantilever ArmsInstalling/Removing the Cantilever Arm Armpad Adjusting the Angle of the Cantilever ArmsRemoving the Contoura Back Removing/Installing the Contoura BackInstalling the Contoura Back Adult BacksRemoving/Installing the Contoura Back Installing the Mounting Hardware onto the Contoura BackAdjusting the Back Angle Adjusting the Back WidthRemoving/Installing the Back Canes Adjusting the Back HeightRemoving/Installing the Back Canes Removing/Installing the Spreader BarRemoving/Installing the Spreader Bar Adjusting Spreader Bar WidthAdjusting Spreader Bar Width Junior Backs 100 Non- Trro Back Cane Bracket Mounting Holes Washer Screws Adjusting the Back Height Removing Spreader Bar Cover Mounting Screw Back Cane Tube Mounting Screws Adult Seats Removing/Installing the Seat PanAdjusting the Seat Width Side Rail Mounting Holes Adjusting the Seat Width Adjusting the Seat Depth Removing Side Rails Removing/Installing Side RailsRemoving/Installing Side Rails Installing Side RailsJunior Seats Junior Seats To be removed for this procedure To be removed for this Cross BAR Mounting Holes Hex Screw Rear Arm Socket Adjustment Table Inch USA Limited Warranty