Invacare Adjustable ASBA Seat Adjusting the Power Elevating Legrests, Adjusting the Footplate

Page 35

SECTION 7—POWER ELEVATING LEGRESTS

6.If necessary, adjust powered legs. Refer to Adjusting the Power Elevating Legrests below.

Removing the Power Elevating Legrests

1.Disconnect power legrests from the harness.

2.Push powered legrest release handle toward the opposite side of the wheelchair and swing legrest to the outside of the wheelchair.

3.Lift powered legrest and remove from wheelchair.

4.Repeat STEPS 1‐3 for opposite power legrest.

 

DETAIL “A”

Mounting

Calf Pad

Mounting Pin

Hole

 

Footplate

Legrest Release

Handle

DETAIL “B”

Jumper

Cable

Power

Legrest

Connector

FIGURE 7.1 Installing/Removing the Power Elevating Legrests

Adjusting the Power Elevating Legrests

Adjusting the Footplate

WARNING

DO NOT remove heel loops without providing some other adequate means of support. Otherwise personal injury may occur.

Adjusting the Footplate Height

NOTE: For this procedure, refer to FIGURE 7.2 on page 36.

NOTE: The following procedure should be performed with the user in the wheelchair.

NOTE: T‐nuts ride in the channels of the exterior/interior rails of the power legrests. Refer to FIGURE 7.2.

1.Loosen, but DO NOT remove, the two interior button screws that secure the footplate assembly to the T‐nuts.

Part No 1143238

35

Adjustable ASBA Seat

Image 35
Contents Adjustable Asba Seat Reference Documents Useful TermsTable of Contents Arms Adult Seats Junior Seats Special Notes Signal Word MeaningSpecial Notes All Wheelchairs with Trro Wheelchairs without Trro Label LocationsAll Wheelchairs Typical Product Parameters Adjustable Asba SeatOperation Information Repair or Service InformationGeneral Guidelines Tire Pressure Weight LimitationPinch Points SAFETY/HANDLING of WheelchairsEMI Information EMI Information Troubleshooting Safety INSPECTION/ TroubleshootingSafety Inspection Checklist Center Mount Footrests Removing Removing/Installing the Manual Center Mount FootrestInstalling Chairs built before 12/01/2008 Adjusting the Height of the Manual Center Mount FootrestChairs built after 12/01/2008 Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Angle of the Manual Center Mount FootrestAdjusting the Footplate Angle Chairs built before 12/01/2008 Adjusting the Footplate AngleAdjusting the Tension of the Flip Up Footplate PH904A, PHAL4A, 70 and PW93 Installing/Removing FootrestsFront Riggings PH904A and PHAL4A Front Riggings Adjusting the Footrest HeightTaper PW93 Adjusting the Footrest Height PW93Raising/Lowering Elevating Front Riggings Replacing Heel LoopsAdjusting/Replacing Telescoping Front Rigging Support Adjusting/Replacing Telescoping Front Rigging SupportInstalling Adjustable Angle Flip-up Footplates Installing Adjustable Angle Flip-up Footplate HingePerpendicular and/or Inversion/Eversion Adjustment Adjusting Adjustable Angle Flip-Up FootplatesDepth Adjustment Angle AdjustmentComposite Replacing Composite/Articulating Footplate Heel Loop14 Installing/Removing Elevating Legrests Installing/Removing Elevating LegrestsRaising/Lowering Elevating Legrests Adjusting CalfpadsInstalling the Power Elevating Legrests Power Elevating LegrestsInstalling/Removing the Power Elevating Legrests Adjusting the Footplate Adjusting the Power Elevating LegrestsRemoving the Power Elevating Legrests Adjusting the Footplate Depth Adjusting the Footplate Angle Adjusting the Calf Pad Width Adjusting the Calf PadAdjusting the Calf Pad Height Adjusting the Length for Power LegrestRemoving/Installing the Power Elevating Legrest Harness Seat frame for clarity Removing/Installing the Power Elevating Legrest ActuatorRight power Arms Installing/Removing Flip Back ArmrestsPositioning Flip Back Armrests for Use Adjusting Flip Back ArmrestsAdjusting Positioning Flip Back Armrests for User TransferInstalling/Removing the Cantilever Arms Installing/Removing the Cantilever ArmsAdjusting the Height of the Cantilever Arms Adjusting the Height of the Cantilever ArmsInstalling/Removing the Cantilever Arm Armpad Adjusting the Angle of the Cantilever ArmsRemoving the Contoura Back Removing/Installing the Contoura BackInstalling the Contoura Back Adult BacksRemoving/Installing the Contoura Back Installing the Mounting Hardware onto the Contoura BackAdjusting the Back Angle Adjusting the Back WidthRemoving/Installing the Back Canes Adjusting the Back HeightRemoving/Installing the Back Canes Removing/Installing the Spreader BarRemoving/Installing the Spreader Bar Adjusting Spreader Bar WidthAdjusting Spreader Bar Width Junior Backs 100 Non- Trro Back Cane Bracket Mounting Holes Washer Screws Adjusting the Back Height Removing Spreader Bar Cover Mounting Screw Back Cane Tube Mounting Screws Adult Seats Removing/Installing the Seat PanAdjusting the Seat Width Side Rail Mounting Holes Adjusting the Seat Width Adjusting the Seat Depth Removing Side Rails Removing/Installing Side RailsRemoving/Installing Side Rails Installing Side RailsJunior Seats Junior Seats To be removed for this procedure To be removed for this Cross BAR Mounting Holes Hex Screw Rear Arm Socket Adjustment Table Inch USA Limited Warranty