Invacare Adjustable ASBA Seat Removing/Installing the Power Elevating Legrest Harness

Page 40

SECTION 7—POWER ELEVATING LEGRESTS

Removing/Installing the Power Elevating Legrest Harness

NOTE: For this procedure, refer to FIGURE 7.9 on page 41.

Removing

1.Unplug the power elevating legrest connector from the harness.

2.Unplug the harness from the TRECM or DLIAM.

3.Cut the tie‐wrap securing the harness to the rear harness wire bracket.

4.Remove the two cap screws and locknuts securing the harness connector to the front harness wire bracket.

Installing

1.If power legrests were not previously installed, perform the following steps:

A.Remove the hex screw and washer securing the front of the rear arm socket to the seat frame.

B.Install the rear harness wire bracket onto the front mounting hole on the rear arm socket using the hex screw.

NOTE: The hex screw will install into the T‐nut in the seat frame.

C.Install the hex screw through the washer and front harness wire bracket and into the T‐nut in the seat frame.

D.Repeat STEPS A‐C for the opposite side of the wheelchair.

2.Secure the power elevating legrest connector to the front harness wire bracket using the two cap screws and locknuts.

3.Tie‐wrap the harness to the rear harness wire bracket (Detail “A”).

4.Plug the harness into the TRECM or DLIAM.

5.Repeat STEPS 2‐4 for the opposite side of the wheelchair.

6.Install the power elevating legrests. Refer to Installing/Removing the Power Elevating Legrests on page 34.

Adjustable ASBA Seat

40

Part No 1143238

Image 40
Contents Adjustable Asba Seat Useful Terms Reference DocumentsTable of Contents Arms Adult Seats Junior Seats Signal Word Meaning Special NotesSpecial Notes All Wheelchairs Label LocationsAll Wheelchairs with Trro Wheelchairs without Trro Adjustable Asba Seat Typical Product ParametersGeneral Guidelines Repair or Service InformationOperation Information Weight Limitation Tire PressureSAFETY/HANDLING of Wheelchairs Pinch PointsEMI Information EMI Information Safety Inspection Checklist Safety INSPECTION/ TroubleshootingTroubleshooting Center Mount Footrests Installing Removing/Installing the Manual Center Mount FootrestRemoving Adjusting the Height of the Manual Center Mount Footrest Chairs built before 12/01/2008Chairs built after 12/01/2008 Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Angle of the Manual Center Mount FootrestAdjusting the Footplate Angle Adjusting the Footplate Angle Chairs built before 12/01/2008Adjusting the Tension of the Flip Up Footplate Front Riggings Installing/Removing FootrestsPH904A, PHAL4A, 70 and PW93 Taper Adjusting the Footrest HeightPH904A and PHAL4A Front Riggings Adjusting the Footrest Height PW93 PW93Replacing Heel Loops Raising/Lowering Elevating Front RiggingsAdjusting/Replacing Telescoping Front Rigging Support Adjusting/Replacing Telescoping Front Rigging SupportInstalling Adjustable Angle Flip-up Footplate Hinge Installing Adjustable Angle Flip-up FootplatesAdjusting Adjustable Angle Flip-Up Footplates Depth AdjustmentAngle Adjustment Perpendicular and/or Inversion/Eversion AdjustmentReplacing Composite/Articulating Footplate Heel Loop CompositeInstalling/Removing Elevating Legrests 14 Installing/Removing Elevating LegrestsAdjusting Calfpads Raising/Lowering Elevating LegrestsInstalling/Removing the Power Elevating Legrests Power Elevating LegrestsInstalling the Power Elevating Legrests Removing the Power Elevating Legrests Adjusting the Power Elevating LegrestsAdjusting the Footplate Adjusting the Footplate Depth Adjusting the Footplate Angle Adjusting the Calf Pad Adjusting the Calf Pad WidthAdjusting the Length for Power Legrest Adjusting the Calf Pad HeightRemoving/Installing the Power Elevating Legrest Harness Removing/Installing the Power Elevating Legrest Actuator Seat frame for clarityRight power Installing/Removing Flip Back Armrests ArmsAdjusting Flip Back Armrests AdjustingPositioning Flip Back Armrests for User Transfer Positioning Flip Back Armrests for UseInstalling/Removing the Cantilever Arms Installing/Removing the Cantilever ArmsAdjusting the Height of the Cantilever Arms Adjusting the Height of the Cantilever ArmsAdjusting the Angle of the Cantilever Arms Installing/Removing the Cantilever Arm ArmpadRemoving/Installing the Contoura Back Installing the Contoura BackAdult Backs Removing the Contoura BackInstalling the Mounting Hardware onto the Contoura Back Removing/Installing the Contoura BackAdjusting the Back Width Adjusting the Back AngleAdjusting the Back Height Removing/Installing the Back CanesRemoving/Installing the Spreader Bar Removing/Installing the Back CanesAdjusting Spreader Bar Width Removing/Installing the Spreader BarAdjusting Spreader Bar Width Junior Backs 100 Non- Trro Back Cane Bracket Mounting Holes Washer Screws Adjusting the Back Height Removing Spreader Bar Cover Mounting Screw Back Cane Tube Mounting Screws Removing/Installing the Seat Pan Adult SeatsAdjusting the Seat Width Side Rail Mounting Holes Adjusting the Seat Width Adjusting the Seat Depth Removing/Installing Side Rails Removing Side RailsInstalling Side Rails Removing/Installing Side RailsJunior Seats Junior Seats To be removed for this procedure To be removed for this Cross BAR Mounting Holes Hex Screw Rear Arm Socket Adjustment Table Inch Limited Warranty USA