Invacare Adjustable ASBA Seat service manual Installing Adjustable Angle Flip-up Footplate Hinge

Page 29

SECTION 6—FRONT RIGGINGS

Installing Adjustable Angle Flip-up Footplate Hinge

NOTE: For this procedure, refer to

FIGURE 6.9.

1.Position footplate hinge on the footrest support tube at the desired height.

2.Position mounting screw, washers, spacer, and locknut on the footrest support as shown.

3.Flip the footplate hinge to the up position.

NOTE: The footplate hinge will fall to the down position.

Footplate

Mounting Screw

Hinge

 

Locknut

Washers

 

Spacer

Footrest Support

 

FIGURE 6.9 Installing Adjustable Angle

Flip-up Footplate Hinge

4.Tighten the mounting screw, washer, and locknut that secure the footplate hinge to the footrest support until the footplate hinge remains in the up position.

5.Check the up and down motion of the footplate hinge to make sure the user of the wheelchair can operate the footplates easily.

NOTE: If footplateʹs motion is too tight, loosen the mounting screw and locknut approximately ¼‐ turn counterclockwise.

NOTE: If the footplateʹs motion is too loose, tighten mounting screw and locknut approximately ¼‐turn clockwise.

6.Adjust footplate. Refer to Installing Adjustable Angle Flip‐up Footplates on page 29.

Installing Adjustable Angle Flip-up Footplates

NOTE: For this procedure, refer to FIGURE 6.10.

1.Slide the half clamp over the footplate hinge.

2.Hand tighten the two flat screws that secure the footplate to the half clamp.

3.Adjust the footplates to the necessary angle and depth for the user. Refer to Adjusting Adjustable Angle Flip‐Up Footplates on page 30.

90° Footrest Support

Flat Screw

Footplate

Hinge

 

Footplate

 

Half Clamp

 

Washer

 

Locknut

Nylon

 

 

Adjustment

 

Screw

Half Clamp

Footplate Hinge

FIGURE 6.10 Installing Adjustable Angle

Flip-up Footplates

Part No 1143238

29

Adjustable ASBA Seat

Image 29
Contents Adjustable Asba Seat Reference Documents Useful TermsTable of Contents Arms Adult Seats Junior Seats Special Notes Signal Word MeaningSpecial Notes All Wheelchairs with Trro Wheelchairs without Trro Label LocationsAll Wheelchairs Typical Product Parameters Adjustable Asba SeatOperation Information Repair or Service InformationGeneral Guidelines Tire Pressure Weight LimitationPinch Points SAFETY/HANDLING of WheelchairsEMI Information EMI Information Troubleshooting Safety INSPECTION/ TroubleshootingSafety Inspection Checklist Center Mount Footrests Removing Removing/Installing the Manual Center Mount FootrestInstalling Chairs built before 12/01/2008 Adjusting the Height of the Manual Center Mount FootrestChairs built after 12/01/2008 Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Angle of the Manual Center Mount FootrestAdjusting the Footplate Angle Chairs built before 12/01/2008 Adjusting the Footplate AngleAdjusting the Tension of the Flip Up Footplate PH904A, PHAL4A, 70 and PW93 Installing/Removing FootrestsFront Riggings PH904A and PHAL4A Front Riggings Adjusting the Footrest HeightTaper PW93 Adjusting the Footrest Height PW93Raising/Lowering Elevating Front Riggings Replacing Heel LoopsAdjusting/Replacing Telescoping Front Rigging Support Adjusting/Replacing Telescoping Front Rigging SupportInstalling Adjustable Angle Flip-up Footplates Installing Adjustable Angle Flip-up Footplate HingeDepth Adjustment Adjusting Adjustable Angle Flip-Up FootplatesAngle Adjustment Perpendicular and/or Inversion/Eversion AdjustmentComposite Replacing Composite/Articulating Footplate Heel Loop14 Installing/Removing Elevating Legrests Installing/Removing Elevating LegrestsRaising/Lowering Elevating Legrests Adjusting CalfpadsInstalling the Power Elevating Legrests Power Elevating LegrestsInstalling/Removing the Power Elevating Legrests Adjusting the Footplate Adjusting the Power Elevating LegrestsRemoving the Power Elevating Legrests Adjusting the Footplate Depth Adjusting the Footplate Angle Adjusting the Calf Pad Width Adjusting the Calf PadAdjusting the Calf Pad Height Adjusting the Length for Power LegrestRemoving/Installing the Power Elevating Legrest Harness Seat frame for clarity Removing/Installing the Power Elevating Legrest ActuatorRight power Arms Installing/Removing Flip Back ArmrestsAdjusting Adjusting Flip Back ArmrestsPositioning Flip Back Armrests for User Transfer Positioning Flip Back Armrests for UseInstalling/Removing the Cantilever Arms Installing/Removing the Cantilever ArmsAdjusting the Height of the Cantilever Arms Adjusting the Height of the Cantilever ArmsInstalling/Removing the Cantilever Arm Armpad Adjusting the Angle of the Cantilever ArmsInstalling the Contoura Back Removing/Installing the Contoura BackAdult Backs Removing the Contoura BackRemoving/Installing the Contoura Back Installing the Mounting Hardware onto the Contoura BackAdjusting the Back Angle Adjusting the Back WidthRemoving/Installing the Back Canes Adjusting the Back HeightRemoving/Installing the Back Canes Removing/Installing the Spreader BarRemoving/Installing the Spreader Bar Adjusting Spreader Bar WidthAdjusting Spreader Bar Width Junior Backs 100 Non- Trro Back Cane Bracket Mounting Holes Washer Screws Adjusting the Back Height Removing Spreader Bar Cover Mounting Screw Back Cane Tube Mounting Screws Adult Seats Removing/Installing the Seat PanAdjusting the Seat Width Side Rail Mounting Holes Adjusting the Seat Width Adjusting the Seat Depth Removing Side Rails Removing/Installing Side RailsRemoving/Installing Side Rails Installing Side RailsJunior Seats Junior Seats To be removed for this procedure To be removed for this Cross BAR Mounting Holes Hex Screw Rear Arm Socket Adjustment Table Inch USA Limited Warranty