Invacare Adjustable ASBA Seat service manual Chairs built after 12/01/2008

Page 20

SECTION 5—CENTER MOUNT FOOTRESTS

Chairs built after 12/01/2008

WARNING

While the wheelchair is moving, minimum ground clearance for the front rigging is three inches. If the wheelchair is not moving, the front rigging MUST maintain a minimum of one inch ground clearance - otherwise personal injury and damage may result.

NOTE: For this procedure, refer to FIGURE 5.3.

1.Remove the two mounting screws that secure the button head cleat to the extension housing.

2.Adjust the footrest extension tube to the desired height.

3.Secure the extension tube to the desired height with the button head cleat and mounting screws. Securely tighten.

4.Repeat STEPS 1‐3 for the other extension tube.

	Extension
Button Head Cleat	Housing

Extension Tube Mounting Holes

Mounting Screws

Extension Tube

FIGURE 5.3 Adjusting the Height of the Manual Center Mount Footrest -

Chairs built after 12/01/2008

Adjustable ASBA Seat

20

Part No 1143238

Image 20

Contents Adjustable Asba Seat Useful Terms Reference DocumentsTable of Contents Arms Adult Seats Junior Seats Signal Word Meaning Special NotesSpecial Notes All Wheelchairs with Trro Wheelchairs without Trro Label LocationsAll Wheelchairs Adjustable Asba Seat Typical Product ParametersOperation Information Repair or Service InformationGeneral Guidelines Weight Limitation Tire PressureSAFETY/HANDLING of Wheelchairs Pinch PointsEMI Information EMI Information Troubleshooting Safety INSPECTION/ TroubleshootingSafety Inspection Checklist Center Mount Footrests Removing Removing/Installing the Manual Center Mount FootrestInstalling Adjusting the Height of the Manual Center Mount Footrest Chairs built before 12/01/2008Chairs built after 12/01/2008 Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Angle of the Manual Center Mount FootrestAdjusting the Footplate Angle Adjusting the Footplate Angle Chairs built before 12/01/2008Adjusting the Tension of the Flip Up Footplate PH904A, PHAL4A, 70 and PW93 Installing/Removing FootrestsFront Riggings PH904A and PHAL4A Front Riggings Adjusting the Footrest HeightTaper Adjusting the Footrest Height PW93 PW93Replacing Heel Loops Raising/Lowering Elevating Front RiggingsAdjusting/Replacing Telescoping Front Rigging Support Adjusting/Replacing Telescoping Front Rigging SupportInstalling Adjustable Angle Flip-up Footplate Hinge Installing Adjustable Angle Flip-up FootplatesAdjusting Adjustable Angle Flip-Up Footplates Depth AdjustmentAngle Adjustment Perpendicular and/or Inversion/Eversion AdjustmentReplacing Composite/Articulating Footplate Heel Loop CompositeInstalling/Removing Elevating Legrests 14 Installing/Removing Elevating LegrestsAdjusting Calfpads Raising/Lowering Elevating LegrestsInstalling the Power Elevating Legrests Power Elevating LegrestsInstalling/Removing the Power Elevating Legrests Adjusting the Footplate Adjusting the Power Elevating LegrestsRemoving the Power Elevating Legrests Adjusting the Footplate Depth Adjusting the Footplate Angle Adjusting the Calf Pad Adjusting the Calf Pad WidthAdjusting the Length for Power Legrest Adjusting the Calf Pad HeightRemoving/Installing the Power Elevating Legrest Harness Removing/Installing the Power Elevating Legrest Actuator Seat frame for clarityRight power Installing/Removing Flip Back Armrests ArmsAdjusting Flip Back Armrests AdjustingPositioning Flip Back Armrests for User Transfer Positioning Flip Back Armrests for UseInstalling/Removing the Cantilever Arms Installing/Removing the Cantilever ArmsAdjusting the Height of the Cantilever Arms Adjusting the Height of the Cantilever ArmsAdjusting the Angle of the Cantilever Arms Installing/Removing the Cantilever Arm ArmpadRemoving/Installing the Contoura Back Installing the Contoura BackAdult Backs Removing the Contoura BackInstalling the Mounting Hardware onto the Contoura Back Removing/Installing the Contoura BackAdjusting the Back Width Adjusting the Back AngleAdjusting the Back Height Removing/Installing the Back CanesRemoving/Installing the Spreader Bar Removing/Installing the Back CanesAdjusting Spreader Bar Width Removing/Installing the Spreader BarAdjusting Spreader Bar Width Junior Backs 100 Non- Trro Back Cane Bracket Mounting Holes Washer Screws Adjusting the Back Height Removing Spreader Bar Cover Mounting Screw Back Cane Tube Mounting Screws Removing/Installing the Seat Pan Adult SeatsAdjusting the Seat Width Side Rail Mounting Holes Adjusting the Seat Width Adjusting the Seat Depth Removing/Installing Side Rails Removing Side RailsInstalling Side Rails Removing/Installing Side RailsJunior Seats Junior Seats To be removed for this procedure To be removed for this Cross BAR Mounting Holes Hex Screw Rear Arm Socket Adjustment Table Inch Limited Warranty USA