Invacare Adjustable ASBA Seat service manual Arms, Installing/Removing Flip Back Armrests

Page 43

SECTION 8—ARMS

SECTION 8—ARMS

WARNING

After ANY adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.

Installing/Removing Flip Back Armrests

WARNING

Make sure the flip back armrest release and height adjustment levers are in the locked position before using the wheelchair.

NOTE: For this procedure, refer to FIGURE 8.1.

NOTE: Flip back armrest release lever must be in the unlocked (up‐horizontal) position when placing the armrest into the arm sockets.

Installing

1. Visually inspect to ensure flip back

armrest release lever is in the unlocked

Flip Back Armrest

Flip Back

(up‐horizontal) position.

Armrest

Locked

2.

Slide the flip back armrest into the arm

 

sockets on the seat frame.

3.

Install the quick‐release pin through

 

the rear arm socket and flip back

 

armrest.

4.

Lock the flip back armrest by pressing

 

the flip back armrest release lever into

 

the down (vertical) position.

5.

Repeat STEPS 1‐4 for the opposite flip

 

back armrest.

Removing

1.Unlock the flip back armrest by positioning the flip back armrest release lever into the up (horizontal) position.

(Down -

Release Vertical)

Lever

 

Unlocked

 

(Up -

Rear

Horizontal)

 

Arm

 

Socket

Seat

Quick-

Frame

Release Pin

Front Arm Socket

 

FIGURE 8.1 Installing/Removing Flip Back

Armrests

2.Remove the quick‐release pin that secures the flip back armrest to the rear arm socket.

3.Pull UP on the flip back armrest and remove the armrest from the arm sockets.

4.Repeat STEPS 1‐3 for the opposite flip back armrest, if necessary.

Part No 1143238

43

Adjustable ASBA Seat

Image 43
Contents Adjustable Asba Seat Reference Documents Useful TermsTable of Contents Arms Adult Seats Junior Seats Special Notes Signal Word MeaningSpecial Notes All Wheelchairs Label LocationsAll Wheelchairs with Trro Wheelchairs without Trro Typical Product Parameters Adjustable Asba SeatGeneral Guidelines Repair or Service InformationOperation Information Tire Pressure Weight LimitationPinch Points SAFETY/HANDLING of WheelchairsEMI Information EMI Information Safety Inspection Checklist Safety INSPECTION/ TroubleshootingTroubleshooting Center Mount Footrests Installing Removing/Installing the Manual Center Mount FootrestRemoving Chairs built before 12/01/2008 Adjusting the Height of the Manual Center Mount FootrestChairs built after 12/01/2008 Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Angle of the Manual Center Mount FootrestAdjusting the Footplate Angle Chairs built before 12/01/2008 Adjusting the Footplate AngleAdjusting the Tension of the Flip Up Footplate Front Riggings Installing/Removing FootrestsPH904A, PHAL4A, 70 and PW93 Taper Adjusting the Footrest HeightPH904A and PHAL4A Front Riggings PW93 Adjusting the Footrest Height PW93Raising/Lowering Elevating Front Riggings Replacing Heel LoopsAdjusting/Replacing Telescoping Front Rigging Support Adjusting/Replacing Telescoping Front Rigging SupportInstalling Adjustable Angle Flip-up Footplates Installing Adjustable Angle Flip-up Footplate HingePerpendicular and/or Inversion/Eversion Adjustment Adjusting Adjustable Angle Flip-Up FootplatesDepth Adjustment Angle AdjustmentComposite Replacing Composite/Articulating Footplate Heel Loop14 Installing/Removing Elevating Legrests Installing/Removing Elevating LegrestsRaising/Lowering Elevating Legrests Adjusting CalfpadsInstalling/Removing the Power Elevating Legrests Power Elevating LegrestsInstalling the Power Elevating Legrests Removing the Power Elevating Legrests Adjusting the Power Elevating LegrestsAdjusting the Footplate Adjusting the Footplate Depth Adjusting the Footplate Angle Adjusting the Calf Pad Width Adjusting the Calf PadAdjusting the Calf Pad Height Adjusting the Length for Power LegrestRemoving/Installing the Power Elevating Legrest Harness Seat frame for clarity Removing/Installing the Power Elevating Legrest ActuatorRight power Arms Installing/Removing Flip Back ArmrestsPositioning Flip Back Armrests for Use Adjusting Flip Back ArmrestsAdjusting Positioning Flip Back Armrests for User TransferInstalling/Removing the Cantilever Arms Installing/Removing the Cantilever ArmsAdjusting the Height of the Cantilever Arms Adjusting the Height of the Cantilever ArmsInstalling/Removing the Cantilever Arm Armpad Adjusting the Angle of the Cantilever ArmsRemoving the Contoura Back Removing/Installing the Contoura BackInstalling the Contoura Back Adult BacksRemoving/Installing the Contoura Back Installing the Mounting Hardware onto the Contoura BackAdjusting the Back Angle Adjusting the Back WidthRemoving/Installing the Back Canes Adjusting the Back HeightRemoving/Installing the Back Canes Removing/Installing the Spreader BarRemoving/Installing the Spreader Bar Adjusting Spreader Bar WidthAdjusting Spreader Bar Width Junior Backs 100 Non- Trro Back Cane Bracket Mounting Holes Washer Screws Adjusting the Back Height Removing Spreader Bar Cover Mounting Screw Back Cane Tube Mounting Screws Adult Seats Removing/Installing the Seat PanAdjusting the Seat Width Side Rail Mounting Holes Adjusting the Seat Width Adjusting the Seat Depth Removing Side Rails Removing/Installing Side RailsRemoving/Installing Side Rails Installing Side RailsJunior Seats Junior Seats To be removed for this procedure To be removed for this Cross BAR Mounting Holes Hex Screw Rear Arm Socket Adjustment Table Inch USA Limited Warranty