Invacare Adjustable ASBA Seat Adjusting the Angle of the Manual Center Mount Footrest

Page 21

SECTION 5—CENTER MOUNT FOOTRESTS

Adjusting the Angle of the Manual Center Mount Footrest

WARNING

While the wheelchair is moving, minimum ground clearance for the front rigging is three inches. If the wheelchair is not moving, the front rigging MUST maintain a minimum of one inch ground clearance - otherwise personal injury and damage may result.

NOTE: For this procedure, refer to FIGURE 5.1 and FIGURE 5.4.

1.Engage the release lever with one hand (not shown) and move the center mount footrest to the desired angle with the other hand.

NOTE: Refer to FIGURE 5.1 for the location of the release lever.

2.Disengage the release lever (not shown) to lock the center mount footrest in the new position.

DETAIL “A” - CHAIRS BUILT BEFORE 12/01/2008

Footplate

Center Mount Footrest

DETAIL “B” - CHAIRS BUILT AFTER 12/01/2008

Footplate

Center Mount Footrest

FIGURE 5.4 Adjusting the Angle of the Manual Center Mount Footrest

Part No 1143238

21

Adjustable ASBA Seat

Image 21

Contents Adjustable Asba Seat Reference Documents Useful TermsTable of Contents Arms Adult Seats Junior Seats Special Notes Signal Word MeaningSpecial Notes Label Locations All WheelchairsAll Wheelchairs with Trro Wheelchairs without Trro Typical Product Parameters Adjustable Asba SeatRepair or Service Information General GuidelinesOperation Information Tire Pressure Weight LimitationPinch Points SAFETY/HANDLING of WheelchairsEMI Information EMI Information Safety INSPECTION/ Troubleshooting Safety Inspection ChecklistTroubleshooting Center Mount Footrests Removing/Installing the Manual Center Mount Footrest InstallingRemoving Chairs built before 12/01/2008 Adjusting the Height of the Manual Center Mount FootrestChairs built after 12/01/2008 Adjusting the Angle of the Manual Center Mount Footrest Adjusting the Angle of the Manual Center Mount FootrestAdjusting the Footplate Angle Chairs built before 12/01/2008 Adjusting the Footplate AngleAdjusting the Tension of the Flip Up Footplate Installing/Removing Footrests Front RiggingsPH904A, PHAL4A, 70 and PW93 Adjusting the Footrest Height TaperPH904A and PHAL4A Front Riggings PW93 Adjusting the Footrest Height PW93Raising/Lowering Elevating Front Riggings Replacing Heel LoopsAdjusting/Replacing Telescoping Front Rigging Support Adjusting/Replacing Telescoping Front Rigging SupportInstalling Adjustable Angle Flip-up Footplates Installing Adjustable Angle Flip-up Footplate HingeDepth Adjustment Adjusting Adjustable Angle Flip-Up FootplatesAngle Adjustment Perpendicular and/or Inversion/Eversion AdjustmentComposite Replacing Composite/Articulating Footplate Heel Loop14 Installing/Removing Elevating Legrests Installing/Removing Elevating LegrestsRaising/Lowering Elevating Legrests Adjusting CalfpadsPower Elevating Legrests Installing/Removing the Power Elevating LegrestsInstalling the Power Elevating Legrests Adjusting the Power Elevating Legrests Removing the Power Elevating LegrestsAdjusting the Footplate Adjusting the Footplate Depth Adjusting the Footplate Angle Adjusting the Calf Pad Width Adjusting the Calf PadAdjusting the Calf Pad Height Adjusting the Length for Power LegrestRemoving/Installing the Power Elevating Legrest Harness Seat frame for clarity Removing/Installing the Power Elevating Legrest ActuatorRight power Arms Installing/Removing Flip Back ArmrestsAdjusting Adjusting Flip Back ArmrestsPositioning Flip Back Armrests for User Transfer Positioning Flip Back Armrests for UseInstalling/Removing the Cantilever Arms Installing/Removing the Cantilever ArmsAdjusting the Height of the Cantilever Arms Adjusting the Height of the Cantilever ArmsInstalling/Removing the Cantilever Arm Armpad Adjusting the Angle of the Cantilever ArmsInstalling the Contoura Back Removing/Installing the Contoura BackAdult Backs Removing the Contoura BackRemoving/Installing the Contoura Back Installing the Mounting Hardware onto the Contoura BackAdjusting the Back Angle Adjusting the Back WidthRemoving/Installing the Back Canes Adjusting the Back HeightRemoving/Installing the Back Canes Removing/Installing the Spreader BarRemoving/Installing the Spreader Bar Adjusting Spreader Bar WidthAdjusting Spreader Bar Width Junior Backs 100 Non- Trro Back Cane Bracket Mounting Holes Washer Screws Adjusting the Back Height Removing Spreader Bar Cover Mounting Screw Back Cane Tube Mounting Screws Adult Seats Removing/Installing the Seat PanAdjusting the Seat Width Side Rail Mounting Holes Adjusting the Seat Width Adjusting the Seat Depth Removing Side Rails Removing/Installing Side RailsRemoving/Installing Side Rails Installing Side RailsJunior Seats Junior Seats To be removed for this procedure To be removed for this Cross BAR Mounting Holes Hex Screw Rear Arm Socket Adjustment Table Inch USA Limited Warranty