Teledyne M5000B operating instructions Hierarchy of System Functions and Subfunctions

Page 31

Photometric Analyzer		Operation /Control Unit 3

System

Dig_filt SetDigital

Filter

	SELF-TEST	Self-Testin	Self-Test
	SELF-TEST	Progress	Results
		Progress	Results
	PWD	Enter	Change
	PWD	Password	Yes/No
		Password	Yes/No
	LOGOUT	SecureSystem
	LOGOUT	setupnotallowed
		setupnotallowed
	MORE
	AUTOCAL	Span/Zerostatus	Span/Zerotiming
		and<>setup	andon/off
	FILSOL	Span/Zero	Enter
	FILSOL	SolenoidorFilter	Enter
		SolenoidorFilter
	TRACK	Settrackor
	or	holdoutput
	HOLD
	CAL-HOLD	Setcal.holdand	Enter
	TIMER	sampleholdtimer	Enter
	TIMER

MORE

ALGORITHM Selectrange Displaygasuse andrange

			Define
	APPLICATION	Selectrange	Application/Range
	OUTPUT:	Setcurrent	Enter
		Setcurrent
	4or20MA	output
	4or20MA	output

MORE

Display

MODEL Model/Version Enter

ShowNegative

SHOW.NEGReading

Change Verify Enter

Password Password

Enter

	Verifydata	Enter
	Points	Enter
	Points
Select		Enter	Enter
Verify/Setup		Input/Output	Enter
	Auto/Manual
	linearCal.
Enter		EnterSpan	Enter
		EnterSpan
		gasvalue
		gasvalue

Figure 3-1: Hierarchy of System Functions and Subfunctions

Teledyne Analytical Instruments

Part I 3-3

Image 31

Contents Teledyne Analytical Instruments Photometric AnalyzerCopyright 1999 Teledyne Analytical Instruments Model 5000BIii Table of ContentsModel 5000B Teledyne Analytical Instruments Part I Control Unit Part IIi Part InstallationOperation Maintenance Model 5000B Photometric Analyzer Iv PartTypical Applications OverviewPhotometric Analyzer Part I Control Unit Introduction Model 5000B Other NIR Absorbers that can be measured consult factory Introduction Model 5000B Main Features of the Analyzer ESCAPE/ENTER Switch 1 UP/DOWN SwitchOperator Interface Model 5000B Controls, Indicators, and Connectors Control Section Interface Panel Model 5000B Interface Panel Introduction Model 5000B Unpacking the Control/Analysis Unit InstallationPart 115VAC Primary Input Power ConnectionsAnalog Output Connections ExamplesRange Voltage Current mA Alarm RelaysTypes of Relay Contacts The connectors are Part I RS-232 Sig RS-232 Pin Purpose RS-232 SignalsCommand Description Testing the SystemParameter Setting Part Photometric Analyzer Operation /Control Unit OperationOperation/Control Unit Hierarchy of System Functions and Subfunctions System Function Setting up an AUTO-CALSelect More and press the Enter Key Entering the Password PasswordProtectionInstalling or Changing the Password Logging Out System Self-Diagnostic Test CheckingLinearitywithALGORITHM Model ScreenSetting 90% Response time seconds Digital Filter SetupFilter or Solenoid Setup Calibration/Hold Timer Setup Hold/Track SetupAnalog 4 to 20 mA Output Calibration Calbrt hold 3 min Sample hold 1 minModel Use UP/DOWN arrow to Adjust 4 ma 250Show Negative Auto Mode ZeroingZero Cal Manual Mode Zeroing Sccm Cell FailureManual Mode Spanning Auto Mode SpanningSpan Cal Offset Function How to access the offset functionZero off 0.0 ppm ENT to begin Zero Select zero mode Auto Select zero mode MANAlarms Function AL1 1ØØØ ppm HI DftN FsN LtchN Manual Select/Define Range Screen Range Select FunctionAuto Screen Precautions 2illustratestheseschemesgraphically Analyze Function Set Range Screen Algorithm Application More Curve Algorithm Screen Auto Mode Linearization Part I Control Unit/Analysis Unit Maintenance Fuse ReplacementAnalog System Self Diagnostic TestMaintenance Model 5000B Photometric Analyzer PowerCell detector PreampPart Part II Analysis Unit Part IIRoutine Maintenance Part II Analysis Unit Appendix Iv Part Operations/Analysis Unit Explosion-ProofVersionControlModule Control FunctionsAnalyzers not equipped with Auto Zero Control SettingsStart-p PreliminaryInspectionPre-Start-upElectricalCheckout Power On ObservationsTeledyneAnalyticalInstruments4-5 Calibration ProcedureStandardizationFluids TeledyneAnalyticalInstruments4-7 Operations/Analysis Unit TeledyneAnalyticalInstruments4-9 Operations/Analysis Unit TeledyneAnalyticalInstruments4-11 Operations/Analysis Unit TeledyneAnalyticalInstruments4-13 Ppm simulated water using Sample Span ZeroAttachment 5000B/5020 NIR Analyzer Operations/Analysis Unit Operational Theory Contd Source Module Sample cell OpticalSystemAnalyzerSystem-BlockDiagram Power Module Block Diagram Detectorcompartment Automatic operation and routine operational duties Routine MaintenancePart II Maintenance/Analysis Unit System Visual Check and Response ProcedureDaily Suggested Preventive Maintenance ScheduleEquipment Required Oscilloscope Display of the I to E Converter Output Part II Maintenance/Analysis Unit Inverting Amplifier Setup of the Logarithmic AmplifierInterface Board Terminals Strip Battery-Powered Oscilloscope Synchronization PointPart Part II Maintenance/Analysis Unit Part Operating Temperature 0-50oC SpecificationsPhotometric Analyzer, 5000B Appendix Appendix Models 5000B Other Features QtyP/NDescription Recommended 2-Year Spare Parts ListDrawing List, 5000B Appendix Models 5000B Teledyne Analytical Instruments