JVC TK-C655 manual Attaching the Ceiling Mount, Attaching the Camera, Attaching a safety wire

Page 16

Connections & Installation

Attaching the Ceiling Mount

To a ceiling slab or channel

Safety wire hole

Ceiling Mount

Rubber seals

 

(Four on each side)

Screws

1. Attaching a safety wire.

Attach a safety wire to the Ceiling Mount and to the ceil- ing slab or channel to prevent the unit from being able to fall to the floor. First attach the safety wire to the Ceiling Mount by passing the wire through the safety wire hole (see the diagram on the left).

MEMO

Connect the wire so that it can be insulated from the ceiling struc- ture. If the ceiling structure is made of a metallic material, inade- quate insulation with the camera may produce noise in the video signal.

Use a wire and ceiling attachment having sufficient length and strength to prevent danger in case the camera drops.

A safety wire is not provided. Please use an appropriate commer- cially available wire.

2. Attaching the Ceiling Mount to the ceiling.

While taking care not to catch the connection cables, at- tach the Ceiling Mount to the ceiling using four screws (as shown in the diagram). Use M4-sized screws or bolts. If woodscrews are used, use those with a diametre of 4.1 mm.

MEMO

Be sure to use four screws and attach them firmly. If the screws are not tightened firmly, dust and moisture may enter the unit via the screw holes.

The rubber seals attached to the Ceiling Mount screw holes of the Ceiling Mount play the role of insulation in case the ceiling struc- ture is made of a metallic material as well as the role of drip proof- ing. If the ceiling structure is made of a metallic material, improper insulation with the camera may produce noise in the video. To prevent this occurring, be sure to ensure correct insulation of the installation.

Attaching the Camera

Attach Drop Prevention Wire to this hook.

Drop Prevention Wire

1. Attach the drop prevention wire.

As shown in the diagram, take the drop prevention wire from the camera and attach it to the hook on the Ceiling Mount.

Be sure to connect the drop prevention wire. Otherwise, the camera will not fit properly to the Ceiling Mount. If they are engaged forcibly, they may be damaged.

CAUTION

Be sure to attach the safety cable. Otherwise, the camera could fall to the floor, caring damage to itself and any person passing underneath.

16

Image 16
Contents TK-C655 Important Safeguards Contents Provided Accessories FeaturesSafety Precautions Precautions for Correct Operation  Preset positionsCamera setups with which auto focusing may be difficult  ZoomingControls, Connectors and Indicators  Ceiling Mount Ceiling Mount  Camera Multi-Drop Communication System Switch settings PCable connections P Memo Turn all the components power off before proceeding Connector side of the Ceiling MountSwitch 7 OFF Switch 8 on Point-to-Point Communication SystemFour wires must be connected Two wires must be connectedDuplex For example connection with an RM-P2580Switch Settings  Setting switchesCamera ID check procedure Machine IDBers on the RM-P2580 ExampleCable Connections Make a 90 mm diameter hole in the ceilingRemove the cover from the Ceiling Mount Pass the cables through the coverAttach the cover Control signal cablesCoaxial cable Attaching a safety wire Attach the drop prevention wireAttaching the Ceiling Mount Attaching the CameraTighten the lock screw using a Phillips screwdriver Ensure that the locking screw is looseFit the camera Rotate the cameraSetup Procedure Setting the camera menus from an RM-P2580Press and hold the Menu button for 3 seconds Press the SET buttonMenu Screen Flow Normal screenCamera Function Screen Camera TITLE/ALARM Screen Camera Video Adjustment Screen Camera ALC/ExDR screenAGC Mode Sense UPAuto PAN/PATROL/TRACE Screen Position Function SET ScreenFactory Settings screen Private Mask Setup Press the Tele button Camera Title SetupRepeat steps 5 and 6 for each title character Area Title Setup Move the cursor to Area Title Edit and press the SET buttonPress the FAR button Repeat steps 5 to 7 for each area titleDisplay the Setup menu on the camera Alarm Title SetupRepeat steps 5 to 7 for each alarm title Set the auto pan mode and speed Auto PAN SetupAdjust the viewing angle of the start position Auto Patrol Setup Auto Trace Setup Move the cursor to Autotrace SET and press the SET buttonSet the patrol start position Auto Trace SET screen is displayedPosition Title Setup Repeat steps 5 to 7 for each title characterPosition Function SET screen Position Title screenAttaching a Flush Mounted Ceiling Bracket Optional WB-S575 Clamp the Flush Mounted Ceiling BracketIng Ceiling plateAttach the ceiling panel Connection CablesRemoving a Flush Mounted Ceiling Bracket Optional WB-S575 Remove the ceiling panelRemove the camera Check the release labels thoroughly before removalTroubleshooting Symptom Cause Information RemedySpecifications CameraPan/Tilt Mechanism GeneralExternal dimensions Unit mm Dimensions in combination with the WB-S575Ceiling Mount hole WB-S575 Flush Mounted Ceiling Bracket + Ceiling panelTK-C655 Dome Type Camera