Setting Up the Camera Using an
PRIVATE MASK Setup
Use the PRIVATE MASK screen to set up the private mask function, which grays out areas that are not required to be included in the monitored picture. Up to four private masks can be set per screen, and up to eight private masks can be set in total.
MENU button
SET button
|
|
| REMOTE CONTROL UNIT | |||
SETUP |
| CAMERA | POSITION |
|
|
|
| POWER |
|
|
|
| |
MENU | SET | ALARM | AUTO | |||
|
| KEY LOCK |
|
|
|
|
| LENS |
|
| CAMERA/POSITION | PAN/TILT | ||
| SPEED |
| 1 | 2 | 3 | CAMERA | POSI- |
|
|
|
|
|
|
| TION |
| IRIS |
| 4 | 5 | 6 | 1 | 2 |
CLOSE | OPEN |
|
|
| OPTION | OPTION | |
NEAR | FOCUS | FAR | 7 | 8 | 9 | AUTO | AUTO |
| AF |
| PAN | PATROL | |||
WIDE | ZOOM | TELE | CLEAR | 0 | ENTER |
|
|
|
|
|
| /HOME |
|
|
|
Numeric keys
CAMERA buttons
PAN/TILT lever
1. Select the camera. ( ☞
CAMERA button → Numeric key (camera number) → ENTER button. The picture of the selected camera is output.
2. Select the angle of view.
Use the PAN/TILT lever and the lens button to set the viewing angle to which the private mask function is to be applied.
3. Display the SETUP menu on the camera. ( ☞ P. 18, steps 1 to 4 )
MENU button (3 sec.) → Select “CAMERA” using the PAN/TILT lever → SET button.
The camera moves to the home position.
TELE ENTER button button
WIDE button
4. Tilt the PAN/TILT lever up or down to move the cursor
(>) to “CAMERA FUNCTION” and press the SET button.
The CAMERA FUNCTION menu is displayed.
– – – C A M E R A F U N C T I O N – – –
P O S . T I T L E L O C . | U P - L |
F L I P | D I G I T A L |
V A R . P / T S P E E D | O N |
E A S Y A F | O F F |
V . S H A R P N E S S | N O R M A L |
P R I V A T E M A S K . . |
|
– – – P R I V A T E M A S K – – –
M O D E |
| O N |
| |
M A S K | N O | 1 | * |
|
M A S K | E D | I T . . |
|
M A S K D E L E T E . .
5. Move the cursor (>) to “PRIVATE MASK” and press the SET button.
The PRIVATE MASK submenu is displayed.
6. Select the private mask function ON or OFF.
Turn the private mask function on or off by setting the “MODE” item in the submenu to ON or OFF (Factory setting: OFF)
7. Select the mask number.
Select the private mask number from MASK NO. 1 to 8 and move the cursor on to the item “MASK EDIT.” Of these, a maximum of 4 can be set within one picture.
If an already set mask number is selected, the (*) mark will be displayed.
8. Edit the masking area.
Already set.
• Move the cursor to “MASK EDIT” and press the SET button to display the MASK EDIT screen. (The masked area will be dis- played as a
• Tilt the PAN/TILT lever to move the
• Press the TELE and WIDE buttons to set the masked area size.
– – – M A S K E D I T – – –
P U S H M E N U → S A V E & R E T U R N
– – – M A S K D E L E T E – – –
C A N C E L
D E L E T E
CAUTIONS
CAUTIONS
●It is not possible to set five or more masks in adjacent areas. (Even when this is attempted, the masked area that is required to be set will not be displayed.)
●MASK cannot be set at lower than approx. 45° in the horizontal direction. (The masks for new settings are not displayed.)
9.Press the MENU button.
•The screen returns to the “PRIVATE MASK menu”.
•To delete a private masked area, select “MASK DELETE”, move the cur- sor to “DELETE” and press the SET button.
The PRIVATE MASK menu reappears after the data has been deleted. To cancel deletion, select “CANCEL” and press the SET button.
10.Repeat steps 6 to 9 for each additional masked area.
11.Press the MENU button.
The screen returns to the “CAMERA FUNCTION” menu.
●Depending on the camera direction, a picture may be shot even in the setting private mask area.
●The private MASK function cannot be carried out during the initializing process immediately after the power is turned on.
●If the picture being shot contains 5 or more masks, the entire picture is masked.
26