JVC TK-C655 manual Ensure that the locking screw is loose, Fit the camera, Rotate the camera

Page 17

Ceiling Mount

Locking screw

Camera

Camera clamping bracket

2.

3.

Ensure that the locking screw is loose.

The camera cannot be attached properly if the locking screw of the Ceiling Mount is too tight at this stage.

Fit the camera.

Check the position of the camera clamping bracket and that of the locking screw, and fit the camera to the Ceiling Mount.

Camera clamping bracket

4. Rotate the camera.

Make sure that the camera is horizontal, then turn the camera clockwise until it stops. Ensure that the camera- clamping bracket is in line with the locking screw of the Ceiling Mount.

Rotate the camera clockwise.

Lock screw

5. Tighten the locking screw.

Tighten the lock screw using a Phillips screwdriver.

CAUTION

If the locking screw is not tightened firmly, the camera may vi- brate or come loose. Be sure to tighten the locking screw firmly.

* To remove the camera from the Ceiling Mount, reverse the steps1 to 5.

Tighten the locking screw.

17

Image 17
Contents TK-C655 Important Safeguards Contents Safety Precautions FeaturesProvided Accessories  Preset positions Precautions for Correct OperationCamera setups with which auto focusing may be difficult  Zooming Ceiling Mount Controls, Connectors and Indicators Ceiling Mount  Camera Cable connections P Switch settings PMulti-Drop Communication System Memo Connector side of the Ceiling Mount Turn all the components power off before proceedingSwitch 7 OFF Switch 8 on Point-to-Point Communication SystemTwo wires must be connected Four wires must be connectedDuplex For example connection with an RM-P2580 Setting switches Switch SettingsMachine ID Camera ID check procedureBers on the RM-P2580 ExampleMake a 90 mm diameter hole in the ceiling Cable ConnectionsRemove the cover from the Ceiling Mount Pass the cables through the coverCoaxial cable Control signal cablesAttach the cover Attach the drop prevention wire Attaching a safety wireAttaching the Ceiling Mount Attaching the CameraEnsure that the locking screw is loose Tighten the lock screw using a Phillips screwdriverFit the camera Rotate the cameraSetting the camera menus from an RM-P2580 Setup ProcedurePress and hold the Menu button for 3 seconds Press the SET buttonNormal screen Menu Screen FlowCamera Function Screen Camera TITLE/ALARM Screen Camera ALC/ExDR screen Camera Video Adjustment ScreenSense UP AGC ModePosition Function SET Screen Auto PAN/PATROL/TRACE ScreenFactory Settings screen Private Mask Setup Repeat steps 5 and 6 for each title character Camera Title SetupPress the Tele button Move the cursor to Area Title Edit and press the SET button Area Title SetupPress the FAR button Repeat steps 5 to 7 for each area titleRepeat steps 5 to 7 for each alarm title Alarm Title SetupDisplay the Setup menu on the camera Adjust the viewing angle of the start position Auto PAN SetupSet the auto pan mode and speed Auto Patrol Setup Move the cursor to Autotrace SET and press the SET button Auto Trace SetupSet the patrol start position Auto Trace SET screen is displayedRepeat steps 5 to 7 for each title character Position Title SetupPosition Function SET screen Position Title screenClamp the Flush Mounted Ceiling Bracket Attaching a Flush Mounted Ceiling Bracket Optional WB-S575Ing Ceiling plateConnection Cables Attach the ceiling panelRemove the ceiling panel Removing a Flush Mounted Ceiling Bracket Optional WB-S575Remove the camera Check the release labels thoroughly before removalSymptom Cause Information Remedy TroubleshootingCamera SpecificationsPan/Tilt Mechanism GeneralDimensions in combination with the WB-S575 External dimensions Unit mmCeiling Mount hole WB-S575 Flush Mounted Ceiling Bracket + Ceiling panelTK-C655 Dome Type Camera