JVC TK-C655 manual Features, Provided Accessories, Safety Precautions

Page 4

Introduction

Features

DSP with a wide dynamic range

Even objects differing greatly in brightness can be monitored clearly.

Private masking facility

When the camera target area needs to be hidden, the camera can be set accordingly to mask it.

Optical zoom lens

Detailed surveillance can be performed with the approx. 25 times optical zoom lens.

High-speed pan/tilt table

The high-speed rotating table with a horizontal panning speed of 300°/sec. and a vertical tilting speed of 180°/sec. makes it possible to get to a preset position very quickly.

Provided Accessories

DOME TYPE CAMERA

 

TK-C655

INSTRUCTIONS

 

 

Screw

 

Screws (M 4 12 mm)

Instructions

Ceiling Mount

Cable plate

(For attaching the Ceiling

(M3 12 mm)

Mount to the Flush Mounted

 

 

For cable plate

 

Ceiling Bracket.)

Safety Precautions

WARNING

Install the unit on a strong and stable surface.

This unit has been designed to rotate at high speed. Due to its weight (about 2.4 kg) and to the vibrations whit it may be subjected, the camera must be mounted to sturdy and stable material. If the ceiling material lacks strength, for example it is made of a decorative laminated material or plasterboard, then the mount should be reinforced using materials such as veneered plywood. If such reinforce- ment is inadequate images may be unstable due to vibration or, in the worst case, the camera may fall and cause a serious accident should there be anyone below it.

For installation, use the provided Ceiling Mount and the optional flush mounted ceiling bracket, which is sold separately.

When installing this device the provided Ceiling Mount and the optional flush mounted ceiling bracket, which is sold separately should be used. Also be sure to connect the drop prevention wire and tighten all screws and nuts firmly.

Power the unit with the rated power voltage.

The power rating for this unit is 24 V AC, 50 Hz/60 Hz. If a power above this rating is supplied, a malfunction will occur or, in the worst case, smoke or fire may be produced.

This unit offers a certain degree of protection against any damage either to itself or to its connection cable that might result from indirect lightning strikes, but it is not capable of preventing all damage caused by lightning strikes, for example it is not protected against a direct strike. If lightning damage can be expected in the place where the unit is installed, be sure to take countermeas- ures by adding an arrester to the connection cable, etc.

CAUTION

Installation of this unit requires special skills. Please be sure to consult JVC authorized dealer about installation procedures.

If the mounting screws or nuts are not tightened sufficiently, the camera may fall from its installation location. Be sure to tighten the mounting nuts firmly to prevent this happening.

Inspect the unit periodically.

Check periodically for any deterioration of the mount sections or loosening of screws due to vibration and ensure that there is no likelihood of the unit dropping.

4

Image 4
Contents TK-C655 Important Safeguards Contents Provided Accessories FeaturesSafety Precautions Precautions for Correct Operation  Preset positionsCamera setups with which auto focusing may be difficult  ZoomingControls, Connectors and Indicators  Ceiling Mount Ceiling Mount  Camera Multi-Drop Communication System Switch settings PCable connections P Memo Turn all the components power off before proceeding Connector side of the Ceiling MountSwitch 7 OFF Switch 8 on Point-to-Point Communication SystemFour wires must be connected Two wires must be connectedDuplex For example connection with an RM-P2580Switch Settings  Setting switchesCamera ID check procedure Machine IDBers on the RM-P2580 ExampleCable Connections Make a 90 mm diameter hole in the ceilingRemove the cover from the Ceiling Mount Pass the cables through the coverAttach the cover Control signal cablesCoaxial cable Attaching a safety wire Attach the drop prevention wireAttaching the Ceiling Mount Attaching the CameraTighten the lock screw using a Phillips screwdriver Ensure that the locking screw is looseFit the camera Rotate the cameraSetup Procedure Setting the camera menus from an RM-P2580Press and hold the Menu button for 3 seconds Press the SET buttonMenu Screen Flow Normal screenCamera Function Screen Camera TITLE/ALARM Screen Camera Video Adjustment Screen Camera ALC/ExDR screenAGC Mode Sense UPAuto PAN/PATROL/TRACE Screen Position Function SET ScreenFactory Settings screen Private Mask Setup Press the Tele button Camera Title SetupRepeat steps 5 and 6 for each title character Area Title Setup Move the cursor to Area Title Edit and press the SET buttonPress the FAR button Repeat steps 5 to 7 for each area titleDisplay the Setup menu on the camera Alarm Title SetupRepeat steps 5 to 7 for each alarm title Set the auto pan mode and speed Auto PAN SetupAdjust the viewing angle of the start position Auto Patrol Setup Auto Trace Setup Move the cursor to Autotrace SET and press the SET buttonSet the patrol start position Auto Trace SET screen is displayedPosition Title Setup Repeat steps 5 to 7 for each title characterPosition Function SET screen Position Title screenAttaching a Flush Mounted Ceiling Bracket Optional WB-S575 Clamp the Flush Mounted Ceiling BracketIng Ceiling plateAttach the ceiling panel Connection CablesRemoving a Flush Mounted Ceiling Bracket Optional WB-S575 Remove the ceiling panelRemove the camera Check the release labels thoroughly before removalTroubleshooting Symptom Cause Information RemedySpecifications CameraPan/Tilt Mechanism GeneralExternal dimensions Unit mm Dimensions in combination with the WB-S575Ceiling Mount hole WB-S575 Flush Mounted Ceiling Bracket + Ceiling panelTK-C655 Dome Type Camera