JVC TK-C655 manual Controls, Connectors and Indicators,  Ceiling Mount

Page 6

Introduction

Controls, Connectors and Indicators

Ceiling Mount

0

Cover

98 7 6

15

2 3 4

(Connector side)

1[VIDEO OUT] Coaxial Cable Connectors

Output connector of a composite video signal (1 V(p-p)) with an output impedance of 75 , to be connected to a switcher, etc.

2[AC ` 24V INPUT] Connector

Connect to a 24 V AC power supply.

3Cover Position Alignment Mark

When attaching the cover, use this mark to align its final position correctly.

4Locking Screw

Tighten this screw to fasten the camera clamping bracket

*.

5Safety Wire Hole

To prevent the possibility of the entire camera falling down, attach the safety wire between this hole and a secure at- taching position in the ceiling.

9

8CONTROL terminal (CN22)

7

6

(Terminal Layout)

8[CONTROL] Terminals (CN22)

Connect to a RM-P2580 remote control unit.

Pin No.

Signal Name

Mark

1

TX +

A

 

 



2

TX –

B

 

 



3

RX +

C

 

 



4

RX –

D

 

 



9Alarm Output Terminals (CN24)

This cannot be used.

0Cover

For protection against dust. Pierce the rubber cap on this

cover and pass the cable through the slits. P. 14

6

7

Alarm Input Terminals (CN26)

This cannot be used.

[ALARM I/O] Input/output Terminals (CN23)

This cannot be used.

6

Image 6
Contents TK-C655 Important Safeguards Contents Features Provided AccessoriesSafety Precautions Camera setups with which auto focusing may be difficult Precautions for Correct Operation Preset positions  ZoomingControls, Connectors and Indicators  Ceiling Mount Ceiling Mount  Camera Switch settings P Multi-Drop Communication SystemCable connections P Memo Switch 7 OFF Switch 8 on Turn all the components power off before proceedingConnector side of the Ceiling Mount Point-to-Point Communication SystemDuplex Four wires must be connectedTwo wires must be connected For example connection with an RM-P2580Switch Settings  Setting switchesBers on the RM-P2580 Camera ID check procedureMachine ID ExampleRemove the cover from the Ceiling Mount Cable ConnectionsMake a 90 mm diameter hole in the ceiling Pass the cables through the coverControl signal cables Attach the coverCoaxial cable Attaching the Ceiling Mount Attaching a safety wireAttach the drop prevention wire Attaching the CameraFit the camera Tighten the lock screw using a Phillips screwdriverEnsure that the locking screw is loose Rotate the cameraPress and hold the Menu button for 3 seconds Setup ProcedureSetting the camera menus from an RM-P2580 Press the SET buttonMenu Screen Flow Normal screenCamera Function Screen Camera TITLE/ALARM Screen Camera Video Adjustment Screen Camera ALC/ExDR screenAGC Mode Sense UPAuto PAN/PATROL/TRACE Screen Position Function SET ScreenFactory Settings screen Private Mask Setup Camera Title Setup Press the Tele buttonRepeat steps 5 and 6 for each title character Press the FAR button Area Title SetupMove the cursor to Area Title Edit and press the SET button Repeat steps 5 to 7 for each area titleAlarm Title Setup Display the Setup menu on the cameraRepeat steps 5 to 7 for each alarm title Auto PAN Setup Set the auto pan mode and speedAdjust the viewing angle of the start position Auto Patrol Setup Set the patrol start position Auto Trace SetupMove the cursor to Autotrace SET and press the SET button Auto Trace SET screen is displayedPosition Function SET screen Position Title SetupRepeat steps 5 to 7 for each title character Position Title screenIng Attaching a Flush Mounted Ceiling Bracket Optional WB-S575Clamp the Flush Mounted Ceiling Bracket Ceiling plateAttach the ceiling panel Connection CablesRemove the camera Removing a Flush Mounted Ceiling Bracket Optional WB-S575Remove the ceiling panel Check the release labels thoroughly before removalTroubleshooting Symptom Cause Information RemedyPan/Tilt Mechanism SpecificationsCamera GeneralCeiling Mount hole External dimensions Unit mmDimensions in combination with the WB-S575 WB-S575 Flush Mounted Ceiling Bracket + Ceiling panelTK-C655 Dome Type Camera