JVC TK-C655 manual Attach the ceiling panel, Connection Cables

Page 35

Anchor bolt mount holes

	Locking
Flush Mounted Ceiling	screw
Flush Mounted Ceiling
Bracket attached to the
ceiling

Ceiling

Mount

Screws (For attaching the Ceiling Mount to the Flush Mounted Ceiling Bracket)

Hook

Ceiling panel

MEMO

4.☞ P. 14, “Connection Cables”

5.Attaching a safety wire to the Ceiling Mount.Connect cables to the Ceiling Mount.

Attach a safety wire to the Ceiling Mount and to the ceiling slab or channel to prevent the unit from dropping. First attach the safety wire to the Ceiling Mount by passing the wire through the safety wire hole.

☞ P. 16, step 1. “Attaching a safety wire”.

6.Attach the Ceiling Mount to the Flush Mounted Ceil- ing Bracket.

• Attach the Ceiling Mount to the Flush Mounted Ceiling Bracket, taking care not to catch the connection cables.

• Please use the four screws provided (M4 x 12 mm). If the screws that have been removed in step 2. above are used, the camera may not be installed properly and may fall.

• Attach so that the locking screw of the Ceiling Mount is positioned below the anchor bolt mounting hole of the Flush Mounted Ceiling Bracket.

7. Attach the camera to the Ceiling Mount. ☞ P. 16, “Attaching the Camera”

8.Attach the ceiling panel.

Attach the ceiling panel, provided with the Flush Mounted Ceiling Bracket, by attaching the two hooks, one an each side.

Both the Flush Mounted Ceiling Bracket and the safety wire should be insulated from the ceiling structure.

If the ceiling structure is made of a metallic material, inadequate insulation with the camera may produce noise in the video output.

35

Image 35

Contents TK-C655 Important Safeguards Contents Safety Precautions FeaturesProvided Accessories Zooming Precautions for Correct Operation Preset positions Camera setups with which auto focusing may be difficult Ceiling Mount Controls, Connectors and Indicators Ceiling Mount Camera Cable connections P Switch settings PMulti-Drop Communication System Memo Point-to-Point Communication System Turn all the components power off before proceedingConnector side of the Ceiling Mount Switch 7 OFF Switch 8 onFor example connection with an RM-P2580 Four wires must be connectedTwo wires must be connected Duplex Setting switches Switch SettingsExample Camera ID check procedureMachine ID Bers on the RM-P2580Pass the cables through the cover Cable ConnectionsMake a 90 mm diameter hole in the ceiling Remove the cover from the Ceiling MountCoaxial cable Control signal cablesAttach the cover Attaching the Camera Attaching a safety wireAttach the drop prevention wire Attaching the Ceiling MountRotate the camera Tighten the lock screw using a Phillips screwdriverEnsure that the locking screw is loose Fit the cameraPress the SET button Setup ProcedureSetting the camera menus from an RM-P2580 Press and hold the Menu button for 3 secondsNormal screen Menu Screen FlowCamera Function Screen Camera TITLE/ALARM Screen Camera ALC/ExDR screen Camera Video Adjustment ScreenSense UP AGC ModePosition Function SET Screen Auto PAN/PATROL/TRACE ScreenFactory Settings screen Private Mask Setup Repeat steps 5 and 6 for each title character Camera Title SetupPress the Tele button Repeat steps 5 to 7 for each area title Area Title SetupMove the cursor to Area Title Edit and press the SET button Press the FAR buttonRepeat steps 5 to 7 for each alarm title Alarm Title SetupDisplay the Setup menu on the camera Adjust the viewing angle of the start position Auto PAN SetupSet the auto pan mode and speed Auto Patrol Setup Auto Trace SET screen is displayed Auto Trace SetupMove the cursor to Autotrace SET and press the SET button Set the patrol start positionPosition Title screen Position Title SetupRepeat steps 5 to 7 for each title character Position Function SET screenCeiling plate Attaching a Flush Mounted Ceiling Bracket Optional WB-S575Clamp the Flush Mounted Ceiling Bracket IngConnection Cables Attach the ceiling panelCheck the release labels thoroughly before removal Removing a Flush Mounted Ceiling Bracket Optional WB-S575Remove the ceiling panel Remove the cameraSymptom Cause Information Remedy TroubleshootingGeneral SpecificationsCamera Pan/Tilt MechanismWB-S575 Flush Mounted Ceiling Bracket + Ceiling panel External dimensions Unit mmDimensions in combination with the WB-S575 Ceiling Mount holeTK-C655 Dome Type Camera