JVC TK-C655 manual Camera Video Adjustment Screen, Camera ALC/ExDR screen

Page 22

Setting Up the Camera Using an RM-P2580

CAMERA VIDEO ADJUSTMENT Screen

This menu sets the picture signal of the camera, such as the colour level and contour enhancement.

Item

 

Function & Setting

Initial Value

 

 

 

COLOUR LEVEL

Sets the colour level of the picture signal.

NORMAL

 

To increase : Set a smaller value.

 

 

To decrease : Set a larger value.

 

 

Setting values : –5 to NORMAL to 5.

 

 

 

 

ENHANCE LEVEL

Sets the contour enhancement which controls the sharpness of the monitor pic-

NORMAL

 

ture.

 

 

 

To soften the picture

: Set a smaller value.

 

 

To sharpen the picture : Set a larger value.

 

 

Setting values

: –5 to NORMAL to 5.

 

 

 

 

PEDESTAL LEVEL

Sets the pedestal level (black level) of the video signal.

NORMAL

 

To darken the picture

: Set a smaller value.

 

 

To brighten the picture : Set a larger value.

 

 

Setting values

: –5 to NORMAL to 5.

 

 

 

 

AUTO BLK. CTL

Use this function when darker parts of a picture are unclear even after the gain has

OFF

 

been increased using the AGC (Auto Gain Control).

 

 

ON : When the black level of the video signal is low, the pedestal level is in-

 

 

creased automatically in order to improve the clarity of the darker parts.

 

 

OFF : Turns this function off.

 

 

 

 

 

CAMERA ALC/ExDR screen

This screen adjusts the settings of automated functions relating to picture brightness.

Item

 

Function & Setting

Initial Value

 

 

AVERAGE : PEAK Sets the method of exposure detection to the ratio between the average and peak

8:2

 

values.

 

 

 

Large Average value : Use this setting when areas other than the highlighted ar-

 

 

 

eas are filled with dark. (Example: 10:0)

 

 

Large Peak value : Use this setting when highlighted areas appear as halation.

 

 

Setting values

(Example: 5:5)

 

 

: 10:0, 9:1, 8:2, 7:3, 6:4, 5:5

 

 

 

 

SHUTTER

Sets the electronic shutter speed.

1/50

 

When the SENSE UP item is set, the only two values that can be selected are 1/50

 

 

and 1/120.

 

 

 

When the item “ExDR MODE” is set to “ON”, the available settings for the SHUT-

 

 

TER are limited to 1/50 and 1/120.

 

 

Setting values : 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000

 

MEMO

To reduce the flickering which occurs under fluorescent lighting, set the shutter speed to 1/50 if your local power supply frequency is 50 Hz and to 1/120 if it is 60 Hz.

When a high shutter speeds are used, white stripes may be observed above and below bright objects. This is called the smear phenomenon and is usual to CCD cameras.

22

Image 22
Contents TK-C655 Important Safeguards Contents Provided Accessories FeaturesSafety Precautions Camera setups with which auto focusing may be difficult Precautions for Correct Operation Preset positions  ZoomingControls, Connectors and Indicators  Ceiling Mount Ceiling Mount  Camera Multi-Drop Communication System Switch settings PCable connections P Memo Switch 7 OFF Switch 8 on Turn all the components power off before proceedingConnector side of the Ceiling Mount Point-to-Point Communication SystemDuplex Four wires must be connectedTwo wires must be connected For example connection with an RM-P2580Switch Settings  Setting switchesBers on the RM-P2580 Camera ID check procedureMachine ID ExampleRemove the cover from the Ceiling Mount Cable ConnectionsMake a 90 mm diameter hole in the ceiling Pass the cables through the coverAttach the cover Control signal cablesCoaxial cable Attaching the Ceiling Mount Attaching a safety wireAttach the drop prevention wire Attaching the CameraFit the camera Tighten the lock screw using a Phillips screwdriverEnsure that the locking screw is loose Rotate the cameraPress and hold the Menu button for 3 seconds Setup ProcedureSetting the camera menus from an RM-P2580 Press the SET buttonMenu Screen Flow Normal screenCamera Function Screen Camera TITLE/ALARM Screen Camera Video Adjustment Screen Camera ALC/ExDR screenAGC Mode Sense UPAuto PAN/PATROL/TRACE Screen Position Function SET ScreenFactory Settings screen Private Mask Setup Press the Tele button Camera Title SetupRepeat steps 5 and 6 for each title character Press the FAR button Area Title SetupMove the cursor to Area Title Edit and press the SET button Repeat steps 5 to 7 for each area titleDisplay the Setup menu on the camera Alarm Title SetupRepeat steps 5 to 7 for each alarm title Set the auto pan mode and speed Auto PAN SetupAdjust the viewing angle of the start position Auto Patrol Setup Set the patrol start position Auto Trace SetupMove the cursor to Autotrace SET and press the SET button Auto Trace SET screen is displayedPosition Function SET screen Position Title SetupRepeat steps 5 to 7 for each title character Position Title screenIng Attaching a Flush Mounted Ceiling Bracket Optional WB-S575Clamp the Flush Mounted Ceiling Bracket Ceiling plateAttach the ceiling panel Connection CablesRemove the camera Removing a Flush Mounted Ceiling Bracket Optional WB-S575Remove the ceiling panel Check the release labels thoroughly before removalTroubleshooting Symptom Cause Information RemedyPan/Tilt Mechanism SpecificationsCamera GeneralCeiling Mount hole External dimensions Unit mmDimensions in combination with the WB-S575 WB-S575 Flush Mounted Ceiling Bracket + Ceiling panelTK-C655 Dome Type Camera