Panasonic WV-NS202 operating instructions Step

Page 24

After formatting the SD memory card, the available size may be smaller than the total size since the default directory is automatically created in the SD memory card.

Compatible SD memory card is as follows. SD memory card manufactured by Panasonic (64 MB, 128 MB, 256 MB, 512 MB, 1 GB, 2GB)

Copy images saved on the SD memory card onto the PC [SD memory card images]

Click the [SD memory card] tab on the "Basic setup" page. (page 15)

The following are descriptions of how to copy images saved on the SD memory card onto the PC.

It is necessary in advance to select "Allow" for "FTP access" on the [Network] tab of the "Network setup" page (page 59).

Important:

It is impossible to copy images saved on the SD memory card when another user is simultaneously obtaining images from the SD memory card.

Depending on the settings of a proxy server or a firewall, images may not be obtained via a network. In this case, refer to the network administrator.

Step 1

Click the [Execute] button of "Access images".

The user authentication window will be displayed.

Step 2

Click the [OK] button after entering the user name and the password.

The folder in which images are to be saved will be displayed.

Step 3

Copy the desired images or the folder onto the PC.

It is impossible to display the image to be saved on this window. Display the image after saving it on the PC.

Note:

When logging in the camera to obtain images, drive B will be displayed first.

Images are saved in different directories according to "Save trigger" ("Save trigger" - "Basic setup"-"SD memory card".).

Move to the directory corresponding to the desired images and obtain them.

Refer to page 78 for further information about the directory structure.

24

Image 24
Contents Network Operating Instructions Contents Preface About these operating instructionsTrademarks and Registered Trademarks Viewer SoftwareMonitor Images on a PC Monitor images from a single cameraStep Refresh interval MPEG-4About the Live 0AUTO Mode *2 SD button manual SD recording button *2Zoom buttons *2 Focus buttons *23PRESET *2 1Control pad/buttons *22BRIGHTNESS buttons *2 4Camera title@ SD recording status indicator Audio output button *3@1Main area *2 Monitor images from multiple cameras Record images on the SD memory card manually Action at an Alarm Occurrence Alarm typeAction at an alarm occurrence Notify of alarm occurrences by e-mailTransmit images onto an FTP server Save images on the SD memory card SD memory card UseAccess restrictions by changing the Http port About the network security of the cameraEquipped security functions How to display the setup menu How to operate the setup menu About the setup menu window Network setup button Maintenance button2Setup Help buttonConfigure the basic settings of the camera Basic setup Configure the basic settings BasicAlarm status update mode Default Real timeAlarm status port Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size VGA Image capture size QvgaJpeg setup Default VGA Image qualityDefault 5 fps Refresh interval JpegMPEG-4 setup Default Normal Refresh interval MPEG-4Default 3 sec Transmission type MPEG-4 transmissionDefault Unicast port2 Audio Default Multicast addressDefault Multicast TTL Available value 1 DefaultDefault OFF Camera title on screen 0-9, A-Z Default 1 min Image HoldCamera title on screen Home positionUpside-down Pan·Tilt degree/Zoom ratio displayTilt Angle Image Adjust Preset PositionAuto Pan Privacy ZoneSuper Dynamic About SUPER-D 3 Super Dynamic functionDefault Auto Default on High Sensitivity upDefault ATW1 Mask areaDefault High Chroma gain level DNR Digital Noise ReductionAperture level Pedestal levelSet mask areas Preset No Preset IDPosition No Preset ID 0-9, A-Z Number of characters for the preset ID 0 16 charDefault OFF Mask area Auto focusPosition Auto panZone setting Privacy zoneMode Zone selectConfigure the settings relating to audio Audio Audio output volume PC to Camera Default Middle Audio output interval PC to CameraAuthentication Audio output port PC to CameraConfigures the multi-screen settings Multi-screen setup IP addressNumber of characters for the IP address 1 Configure the alarm settings Alarm setup Configure the settings relating to the alarm AlarmAlarm setup Camera motion on alarm Default OFF Command alarm Configure the settings relating to the alarm image Alarm image setupConfigure the settings relating to the alarm out connector Alarm output terminal setupAUX name Set the VMD areas VMD area Default OFF Detection sensitivity Default MiddleStatus Set the VMD areas for each preset position Delete the VMD area set for the designated preset position Default Middle StepMail notification setup Configure the settings relating to Panasonic alarm protocol Panasonic alarm protocol setupPanasonic alarm protocol User authentication Default OFF User namePassword Retype password Number of characters for the password 4 32 charHost authentication Default OFF Access levelConfigure the settings of the servers Server setup Configure the settings relating to the mail server MailConfigure the settings relating to the FTP server FTP FTP modeDefault Passive FTP server address Number of characters for the FTP server addressConfiguring the network settings Network setup Configure the network settings NetworkNetwork setup Default gateway Unavailable IP addresses for the default gate- wayAvailable port number 1 Default Port numbers already in use Default Manual Primary DNS, Secondary DNSWAN Configure the settings relating to Ddns Ddns Access intervalDefault OFF Host name Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp Default OFF Directory FTP periodic transmissionFTP periodic transmission Number of characters for the directory name 0Schedule setup How to configure the schedule settingsInterval How to delete the set schedule Maintenance of the camera Maintenance Error messageCheck the system log System log Time & dateUpgrade the firmware Upgrade How to upgrade the firmwareInitialize setup data and Html data Initialize/restart the camera InitializationInitialize Html data RestartError indications relating to Smtp Error indications relating to FTPAbout the displayed system log Category Indication DescriptionError indications relating to Ddns Error indications relating to NTPTroubleshooting Cause/solutionSymptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages Directory Structure of Drive B FTPN0706-1096 3TR004483BAA
Related manuals
Manual 3 pages 60.95 Kb