Panasonic WV-NS202 operating instructions Solutions Reference Pages

Page 77

When using a PC on which Windows® XP Service Pack2 (SP2) is installed

The following may occur during operation when using a PC on which Windows® XP Service Pack2 (SP2) is installed. Follow the instructions below when the following has occurred. By performing the following solutions, other applica- tions and the security level may not be affected.

The "Information Bar" expressed in the following symptom and solutions will be displayed just below the address bar only when there is information to communicate.

Symptom

The following message is displayed on the information bar.

"Pop-up blocked. To see this pop-up or additional options, click here…"

The following message is displayed on the information bar. "This site might require the following Active X control: 'nwcv3setup.exe' from 'Matsushita Electric Industrial Co., Ltd'. Click here to install..."

An unnecessary status bar or scroll bar is displayed on the pop-up window.

Images are not displayed or refreshed smoothly.

Information Bar

 

Solutions

Reference

 

pages

 

 

Click the information bar and select "Always Allow

 

 

 

 

Pop-ups from This Site…". The dialog window saying

 

 

"Allow pop-ups from this site?" will be displayed. Click

 

the [Yes] button.

 

 

Click the information bar and select "Install Active X

 

 

 

 

Control".

 

 

The "Security Warning" window will be displayed.

 

 

Click the "Install" button on the displayed "Security

 

Warning" window.

 

 

 

 

 

Click "Internet Options" on the Tools menu of Internet

 

 

Explorer, and then click the [Security] tab. Then, click

 

 

the [Custom Level…] button to open the "Security

 

 

Setting" window. Under "Miscellaneous", select

 

"Enable" for "Allow script-initiated windows without

 

 

 

size or position constraints". Click the [OK] button.

 

 

The "Warning" window will be displayed. Click the

 

 

[Yes] button.

 

Delete temporary internet files as follows.

 

 

 

1. Select "Internet Options…" from "Tools" on the

 

 

menu bar of Internet Explorer®. The "Internet

 

Options" window will be displayed.

 

 

2.Click the [Delete Files…] button in the "Temporary Internet files" section on the [General] tab.

77

Image 77
Contents Network Operating Instructions Contents About these operating instructions PrefaceTrademarks and Registered Trademarks Viewer SoftwareMonitor images from a single camera Monitor Images on a PCStep Refresh interval MPEG-4About the Live SD button manual SD recording button *2 0AUTO Mode *2Zoom buttons *2 Focus buttons *21Control pad/buttons *2 3PRESET *22BRIGHTNESS buttons *2 4Camera title@1Main area *2 @ SD recording status indicatorAudio output button *3 Monitor images from multiple cameras Record images on the SD memory card manually Alarm type Action at an Alarm OccurrenceAction at an alarm occurrence Notify of alarm occurrences by e-mailTransmit images onto an FTP server SD memory card Use Save images on the SD memory cardEquipped security functions Access restrictions by changing the Http portAbout the network security of the camera How to display the setup menu How to operate the setup menu About the setup menu window Maintenance button Network setup button2Setup Help buttonConfigure the basic settings Basic Configure the basic settings of the camera Basic setupDefault Real time Alarm status update modeAlarm status port Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size Qvga Image capture size VGADefault VGA Image quality Jpeg setupDefault 5 fps Refresh interval JpegDefault Normal Refresh interval MPEG-4 MPEG-4 setupDefault 3 sec Transmission type MPEG-4 transmissionDefault Multicast address Default Unicast port2 AudioDefault Multicast TTL Available value 1 DefaultDefault 1 min Image Hold Default OFF Camera title on screen 0-9, A-ZCamera title on screen Home positionTilt Angle Upside-downPan·Tilt degree/Zoom ratio display Preset Position Image AdjustAuto Pan Privacy ZoneAbout SUPER-D 3 Super Dynamic function Super DynamicDefault on High Sensitivity up Default AutoDefault ATW1 Mask areaDNR Digital Noise Reduction Default High Chroma gain levelAperture level Pedestal levelSet mask areas Position No Preset NoPreset ID Number of characters for the preset ID 0 16 char Preset ID 0-9, A-ZDefault OFF Mask area Auto focusAuto pan PositionPrivacy zone Zone settingMode Zone selectConfigure the settings relating to audio Audio Default Middle Audio output interval PC to Camera Audio output volume PC to CameraAuthentication Audio output port PC to CameraNumber of characters for the IP address 1 Configures the multi-screen settings Multi-screen setupIP address Alarm setup Configure the alarm settings Alarm setupConfigure the settings relating to the alarm Alarm Camera motion on alarm Default OFF Command alarm Alarm image setup Configure the settings relating to the alarm imageAUX name Configure the settings relating to the alarm out connectorAlarm output terminal setup Set the VMD areas VMD area Status Default OFF Detection sensitivityDefault Middle Set the VMD areas for each preset position Default Middle Step Delete the VMD area set for the designated preset positionMail notification setup Panasonic alarm protocol Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol setup Default OFF User name User authenticationPassword Retype password Number of characters for the password 4 32 charDefault OFF Access level Host authenticationConfigure the settings relating to the mail server Mail Configure the settings of the servers Server setupFTP mode Configure the settings relating to the FTP server FTPDefault Passive FTP server address Number of characters for the FTP server addressNetwork setup Configuring the network settings Network setupConfigure the network settings Network Unavailable IP addresses for the default gate- way Default gatewayAvailable port number 1 Default Port numbers already in use Default Manual Primary DNS, Secondary DNSWAN Access interval Configure the settings relating to Ddns DdnsDefault OFF Host name Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp FTP periodic transmission Default OFF DirectoryFTP periodic transmission Number of characters for the directory name 0Interval Schedule setupHow to configure the schedule settings How to delete the set schedule Error message Maintenance of the camera MaintenanceCheck the system log System log Time & dateHow to upgrade the firmware Upgrade the firmware UpgradeInitialize/restart the camera Initialization Initialize setup data and Html dataInitialize Html data RestartError indications relating to FTP Error indications relating to SmtpAbout the displayed system log Category Indication DescriptionError indications relating to NTP Error indications relating to DdnsCause/solution TroubleshootingSymptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages FTP Directory Structure of Drive BN0706-1096 3TR004483BAA
Related manuals
Manual 3 pages 60.95 Kb