Panasonic WV-NS202 operating instructions About SUPER-D 3 Super Dynamic function

Page 32

Configure the settings relating to image quality ("Image Adjust" setup menu)

Click the [SETUP>>] button of "Image Adjust" on the [Image/Position] tab of the "Camera setup" page. (page 31) The settings relating to image quality can be configured with the setup menu displayed in a newly displayed window. When the values are changed, the changed values will be applied immediately to the currently displayed image on the [Image/Position] tab.

[Super Dynamic 3]

Select "ON" or "OFF" to determine whether to turn on or off super dynamic 3 (SUPER-D 3).

Refer to the next page for further information about SUPER-D 3.

ON: Turn on SUPER-D 3

OFF: Turn off SUPER-D 3

Default: OFF

Note:

In the following cases, turn off SUPER-D 3.

• When flickering appears or the color changes on the screen

• When noise appears in the brighter area on the screen

About SUPER-D 3 (Super Dynamic function)

When there is wide variation between the illumination of light and dark areas of the location being monitored, the camera adjusts the lens iris in accordance with the brighter areas. This causes loss of detail in darker areas. Conversely, adjusting the lens brightness for the darker areas causes the brighter areas to become washed out. SUPER-D 3 digitally combines an image that is set up for a clear view of the brighter areas with an image that is set up for a clear view of the darker areas, creating a final image that preserves over- all detail.

Subject in the dark

Subject in the bright

area is hard to notice…

area is washed out…

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Creates a clearer image by digitally combining images.

32

Image 32
Contents Network Operating Instructions Contents Preface About these operating instructionsTrademarks and Registered Trademarks Viewer SoftwareMonitor Images on a PC Monitor images from a single cameraStep Refresh interval MPEG-4About the Live 0AUTO Mode *2 SD button manual SD recording button *2Zoom buttons *2 Focus buttons *23PRESET *2 1Control pad/buttons *22BRIGHTNESS buttons *2 4Camera title@1Main area *2 @ SD recording status indicatorAudio output button *3 Monitor images from multiple cameras Record images on the SD memory card manually Action at an Alarm Occurrence Alarm typeAction at an alarm occurrence Notify of alarm occurrences by e-mailTransmit images onto an FTP server Save images on the SD memory card SD memory card UseEquipped security functions Access restrictions by changing the Http portAbout the network security of the camera How to display the setup menu How to operate the setup menu About the setup menu window Network setup button Maintenance button2Setup Help buttonConfigure the basic settings of the camera Basic setup Configure the basic settings BasicAlarm status update mode Default Real timeAlarm status port Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size VGA Image capture size QvgaJpeg setup Default VGA Image qualityDefault 5 fps Refresh interval JpegMPEG-4 setup Default Normal Refresh interval MPEG-4Default 3 sec Transmission type MPEG-4 transmissionDefault Unicast port2 Audio Default Multicast addressDefault Multicast TTL Available value 1 DefaultDefault OFF Camera title on screen 0-9, A-Z Default 1 min Image HoldCamera title on screen Home positionTilt Angle Upside-downPan·Tilt degree/Zoom ratio display Image Adjust Preset PositionAuto Pan Privacy ZoneSuper Dynamic About SUPER-D 3 Super Dynamic functionDefault Auto Default on High Sensitivity upDefault ATW1 Mask areaDefault High Chroma gain level DNR Digital Noise ReductionAperture level Pedestal levelSet mask areas Position No Preset NoPreset ID Preset ID 0-9, A-Z Number of characters for the preset ID 0 16 charDefault OFF Mask area Auto focusPosition Auto panZone setting Privacy zoneMode Zone selectConfigure the settings relating to audio Audio Audio output volume PC to Camera Default Middle Audio output interval PC to CameraAuthentication Audio output port PC to CameraNumber of characters for the IP address 1 Configures the multi-screen settings Multi-screen setupIP address Alarm setup Configure the alarm settings Alarm setupConfigure the settings relating to the alarm Alarm Camera motion on alarm Default OFF Command alarm Configure the settings relating to the alarm image Alarm image setupAUX name Configure the settings relating to the alarm out connectorAlarm output terminal setup Set the VMD areas VMD area Status Default OFF Detection sensitivityDefault Middle Set the VMD areas for each preset position Delete the VMD area set for the designated preset position Default Middle StepMail notification setup Panasonic alarm protocol Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol setup User authentication Default OFF User namePassword Retype password Number of characters for the password 4 32 charHost authentication Default OFF Access levelConfigure the settings of the servers Server setup Configure the settings relating to the mail server MailConfigure the settings relating to the FTP server FTP FTP modeDefault Passive FTP server address Number of characters for the FTP server addressNetwork setup Configuring the network settings Network setupConfigure the network settings Network Default gateway Unavailable IP addresses for the default gate- wayAvailable port number 1 Default Port numbers already in use Default Manual Primary DNS, Secondary DNSWAN Configure the settings relating to Ddns Ddns Access intervalDefault OFF Host name Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp Default OFF Directory FTP periodic transmissionFTP periodic transmission Number of characters for the directory name 0Interval Schedule setupHow to configure the schedule settings How to delete the set schedule Maintenance of the camera Maintenance Error messageCheck the system log System log Time & dateUpgrade the firmware Upgrade How to upgrade the firmwareInitialize setup data and Html data Initialize/restart the camera InitializationInitialize Html data RestartError indications relating to Smtp Error indications relating to FTPAbout the displayed system log Category Indication DescriptionError indications relating to Ddns Error indications relating to NTPTroubleshooting Cause/solutionSymptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages Directory Structure of Drive B FTPN0706-1096 3TR004483BAA
Related manuals
Manual 3 pages 60.95 Kb