Panasonic WV-NS202 operating instructions Host authentication, Default OFF Access level

Page 55

Configure the settings relating to the host authentication [Host]

Click the [Host] tab on the "Authentication setup" page. (page 15)

The settings to restrict PCs (IP address) from accessing the camera can be configured on this page.

[Host authentication]

Select "ON" or "OFF" to determine whether or not to authenticate the host.

Default: OFF

[Access level]

Select the access level of the host from the following.

1.Administrator/2. Camera control/3. Live only Refer to page 54 for further information about the access level.

Default: 3. Live only

Note:

By clicking [i] of "Host check", the registered host can be selected and the selected host’s IP address can be checked.

The registered IP address will be displayed with the access level. (Example: 192.168.0.21 [1])

To delete the registered host, click the [DEL] button after selecting the IP address to be deleted.

Important:

Before configuring the host authentication, it is nec- essary to register IP addresses of the PCs to be allowed to access the camera and determine their access levels. If "ON" is selected for "Host authenti- cation" before registering the hosts (IP addresses), it will be impossible to access the camera.

[IP address]

Enter the IP address of the PC to be allowed to access the camera.

Host name is unavailable for the IP address.

Notes:

When "IP address/subnet mask" is entered, it is pos- sible to restrict PCs in each subnet.

For example, when "192.168.0.1/24" is entered and "2. Camera control" is selected for the access level, the PCs whose IP address is between "192.168.0.0" - "192.168.0.255" can access the camera with the access level "2. Camera control".

When the IP address already in use is entered and the [SET] button is clicked, the respective host infor- mation will be overwritten.

55

Image 55
Contents Network Operating Instructions Contents Viewer Software PrefaceAbout these operating instructions Trademarks and Registered TrademarksRefresh interval MPEG-4 Monitor Images on a PCMonitor images from a single camera StepAbout the Live Focus buttons *2 0AUTO Mode *2SD button manual SD recording button *2 Zoom buttons *24Camera title 3PRESET *21Control pad/buttons *2 2BRIGHTNESS buttons *2Audio output button *3 @ SD recording status indicator@1Main area *2 Monitor images from multiple cameras Record images on the SD memory card manually Notify of alarm occurrences by e-mail Action at an Alarm OccurrenceAlarm type Action at an alarm occurrenceTransmit images onto an FTP server SD memory card Use Save images on the SD memory cardAbout the network security of the camera Access restrictions by changing the Http portEquipped security functions How to display the setup menu How to operate the setup menu About the setup menu window Help button Network setup buttonMaintenance button 2SetupConfigure the basic settings Basic Configure the basic settings of the camera Basic setupDefault on Alarm status update modeDefault Real time Alarm status portConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size Qvga Image capture size VGARefresh interval Jpeg Jpeg setupDefault VGA Image quality Default 5 fpsMPEG-4 transmission MPEG-4 setupDefault Normal Refresh interval MPEG-4 Default 3 sec Transmission typeAvailable value 1 Default Default Unicast port2 AudioDefault Multicast address Default Multicast TTLHome position Default OFF Camera title on screen 0-9, A-ZDefault 1 min Image Hold Camera title on screenPan·Tilt degree/Zoom ratio display Upside-downTilt Angle Privacy Zone Image AdjustPreset Position Auto PanAbout SUPER-D 3 Super Dynamic function Super DynamicMask area Default AutoDefault on High Sensitivity up Default ATW1Pedestal level Default High Chroma gain levelDNR Digital Noise Reduction Aperture levelSet mask areas Preset ID Preset NoPosition No Auto focus Preset ID 0-9, A-ZNumber of characters for the preset ID 0 16 char Default OFF Mask areaAuto pan PositionZone select Zone settingPrivacy zone ModeConfigure the settings relating to audio Audio Audio output port PC to Camera Audio output volume PC to CameraDefault Middle Audio output interval PC to Camera AuthenticationIP address Configures the multi-screen settings Multi-screen setupNumber of characters for the IP address 1 Configure the settings relating to the alarm Alarm Configure the alarm settings Alarm setupAlarm setup Camera motion on alarm Default OFF Command alarm Alarm image setup Configure the settings relating to the alarm imageAlarm output terminal setup Configure the settings relating to the alarm out connectorAUX name Set the VMD areas VMD area Default Middle Default OFF Detection sensitivityStatus Set the VMD areas for each preset position Default Middle Step Delete the VMD area set for the designated preset positionMail notification setup Panasonic alarm protocol setup Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol Number of characters for the password 4 32 char User authenticationDefault OFF User name Password Retype passwordDefault OFF Access level Host authenticationConfigure the settings relating to the mail server Mail Configure the settings of the servers Server setupNumber of characters for the FTP server address Configure the settings relating to the FTP server FTPFTP mode Default Passive FTP server addressConfigure the network settings Network Configuring the network settings Network setupNetwork setup Default Manual Primary DNS, Secondary DNS Default gatewayUnavailable IP addresses for the default gate- way Available port number 1 Default Port numbers already in useWAN Number of characters for the host name 1 64 char Configure the settings relating to Ddns DdnsAccess interval Default OFF Host nameConfigure the settings relating to Snmp Snmp Number of characters for the directory name 0 Default OFF DirectoryFTP periodic transmission FTP periodic transmissionHow to configure the schedule settings Schedule setupInterval How to delete the set schedule Time & date Maintenance of the camera MaintenanceError message Check the system log System logHow to upgrade the firmware Upgrade the firmware UpgradeRestart Initialize setup data and Html dataInitialize/restart the camera Initialization Initialize Html dataCategory Indication Description Error indications relating to SmtpError indications relating to FTP About the displayed system logError indications relating to NTP Error indications relating to DdnsCause/solution TroubleshootingSymptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages FTP Directory Structure of Drive BN0706-1096 3TR004483BAA
Related manuals
Manual 3 pages 60.95 Kb