Rockford Fosgate T30001 BD Troubleshooting, Procedure 1 Check Amplifier for proper connections

Page 13

TROUBLESHOOTING

NOTE:If you are having problems after installation follow the Troubleshooting procedures below.

Procedure 1: Check Amplifier for proper connections.

Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue.

1. Check in-line fuse on battery positive cable. Replace if necessary.

2. Check fuse(s) on amplifier. Replace if necessary.

3. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary.

4. Verify there is 10.5 - 15.5 Volts present at the positive battery and remote turn-on cable.Verify quality connections for both cables at amplifier, stereo, and battery/fuseholder. Repair/replace if necessary.

Procedure 2: Protect or Thermal light is on.

1. If the Protect light is on, this is a sign of a possible short in the speaker connections. Check for proper speaker connections and use an ohm meter to check for possible shorts in the speaker wiring. Too low of a speaker impedance may also cause Protect to light.

2. If the Thermal light is on, this is usually a sign of driving the amplifier at very high power levels without adequate airflow around the amplifier. Shut off the system and allow to cool. Check for proper speaker impedance, rewire if needed. Low battery voltage may also cause Thermal to light. Check that the vehicle charging system is maintaining proper voltage. If the previous items do not solve the problem, a fault may be in the amplifier, call customer service for support.

Procedure 3: Check Amplifier for audio output.

1. Verify good RCA input connections at stereo and amplifier. Check entire length of cables for kinks, splices, etc.Test RCA inputs for AC volts with stereo on. Repair/replace if necessary.

2. Disconnect RCA input from amplifier. Connect RCA input from test stereo directly to amplifier input.

Procedure 4: Check Amplifier if you experience Turn-on Pop.

1. Disconnect input signal to amplifier and turn amplifier on and off.

2. If the noise is eliminated, connect the REMOTE lead of amplifier to source unit with a delay turn-on module.

OR

1. Use a different 12 Volt source for REMOTE lead of amplifier (i.e. battery direct).

2. If the noise is eliminated, use a relay to isolate the amplifier from noisy turn-on output.

Procedure 5: Check Amplifier if you experience excess Engine Noise.

1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.

OR

2. Bypass any and all electrical components between the stereo and the amplifier(s). Connect stereo directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise.

OR

3. Remove existing ground wires for all electrical components. Reground wires to different locations. Verify that grounding location is clean, shiny metal free of paint, rust etc.

OR

4. Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.

OR

5. Have alternator and battery load tested by your mechanic.Verify good working order of vehicle electrical system including distributor, spark plugs, spark plug wires, voltage regulator etc.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Installation Operation Introduction Table of ContentsContents of Carton Safety InstructionsRating. See Specifications for fuse ratings Design FeaturesProt Distortion and increases efficiencyInstallation Considerations InstallationEngine Compartment Mounting LocationsTrunk Mounting Passenger Compartment MountingWiring the System Installation Battery and ChargingCurrent and could induce noise into the audio system Source to activate the amplifierSingle Power Connection Single Amplifier WiringBoost Operation PARA-PUNCH Remote BassMounting Clip Adjusting Crossover Frequency Operation Adjusting GainMode Switch Infrasonic FilterOperation Multiple Amplifier WiringMaster SlaveBd Sync Wiring Operation Phase SwitchProcedure 1 Check Amplifier for proper connections TroubleshootingProcedure 2 Protect or Thermal light is on Procedure 3 Check Amplifier for audio outputMODEL- Power SpecificationsSpecifications subject to change without notice T30001 bdLimited Warranty Information Length of WarrantyNuméro de modèle Table DES MatièresAvertissement Mise EN Garde Consignes DE SécuritéCette DEL rouge sillumine si lampli atteint le troisième Particularités TechniquesCette DEL jaune sillumine si un court-circuit ou une Haut-parleurs Installation Considérations Concernant L’INSTALLATIONConfiez la tâche à un technicien qualifié Emplacements DE MontageDe dommages à lappareil Votre distributeur agréé Rockford Fosgate Installation Batterie ET ChargeREM à une source positive commutée de 12 volts. La tension Pour activer lampliCauser des blessures ou endommager lampli et/ou les Ces amplis ne sont pas recommandés pour des chargesAvertissement Par paires damplisAttache de fixation Fonctionnement Télécommande DE Basses PARA-PUNCHFonctionnement Réglage DU Gain Sélecteur DE ModeRéglage DE LA Fréquence DU Filtre Passif Filtre InfrasoniqueCâblage pour plusieurs amplis FonctionnementMaître Réglé surCâblage bd Sync Fonctionnement Commutateur DE PhaseSet to Bd SyncProcédure 2 Le voyant de protection ou thermique est allumé DépannageProcédure 3 Vérifiez la sortie audio de lampli Caractéristiques Modèle PowerLes spécifications sont sujettes à changements sans préavis Informations SUR LA Garantie Limitée Durée de la garantieÍndice DE Materias IntroducciónNúmero de la serie Número del modelo NOTALea cada sección para obtener información más detalladaPrecaución Instrucciones DE SeguridadContenido DE LA Caja LED de temperatura Par La unidadLED de protección Parte superior Distorsión y aumenta la eficienciaInstalación Consideraciones Para LA Instalación Lugares DE Montaje InstalaciónCompartimento del motor Instalación en el maleteroCableado DEL Sistema Instalación Bateríay CargaVoltios para activar el amplificador Daños al amplificador o a los componentes conectados Broche de montaje Funcionamiento PARA-PUNCH Remote BassInstalación del panel externo Instalación del panelAjuste DE LA Frecuencia X-OVER Transición Funcionamiento Ajuste DE GananciaFiltro Infrasónico Interruptor DE ModoMaestro FuncionamientoEsclavo Cableado de sincronización de db Funcionamiento Interruptor DE FaseEstá encendida vaya al Paso 3,de otra manera,continúe Solución DE ProblemasEspecificaciones Modelo PowerRockford SpeakersAcoustic Design Speaker Returns Información Sobre LA Garantía LimitadaInhaltsverzeichnis EinleitungSeriennummer Modellnummer Einleitung Sicherheitshinweise DesigncharakteristikenDieses Symbol mit dem Wort „VORSICHT soll den Benutzer auf Dieses Symbol mit dem Wort „WARNUNG soll den Benutzer aufSicherheitshinweise Führt zu schweren Verletzungen oder TodDiese rote LED leuchtet auf, wenn der Verstärker die dritte DesigncharakteristikenDesigncharakteristiken Einbau EinbauüberlegungenBefestigungsstellen EinbauMotorraum Einbau im KofferraumVerkabelung DES Systems Einbau Batterie UND AufladungVerursachen Angeschlossenen Komponenten verursacht werden Stromzufuhr zum Verstärker abgeschaltet oder entfernt wurdeOder Pro überbrücktem Verstärkerpaar empfohlenBefestigungs Klemme Betrieb PARA-PUNCHBASS-FERNBEDIENUNGBefestigung und Einbau Einbau im ArmaturenbrettCROSSOVER-FREQUENZ Einstellen Betrieb Lautstärke Gain EinstellenInfraschallfilter FunktionsschalterBetrieb Bd-Synchronverkabelung Betrieb PhasenschalterVerfahren 2Schutz- oderThermallicht leuchtet auf FehlerbeseitigungVerfahren 3DenVerstärker aufAudioleistung überprüfen OderTechnische Daten MODELL- PowerT10001 bd Die technischen Daten können sich ohne Ankündigung ändernInformationen ZUR Beschränkten Garantie Laufzeit der GarantieIndice IntroduzioneNumero di serie Numero di modello Nota Ripassare ciascuna sezione per ulteriori ragguagliContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaLED temp Caratteristiche DEL DesignAutomaticamente TerminaliComando Installazione Considerazioni SULL’INSTALLAZIONEInterru Posizionamento InstallazioneScompartimento del motore Montaggio nel bagagliaioCablaggio DEL Sistema Installazione Batteria E CaricamentoSistema audio Singlesingle Graffa di Montaggio Funzionamento Comando a Distanza PER Toni Bassi PARA-PUNCHRegolazione Della Frequenza DI Incrocio Funzionamento Regolazione DEL GuadagnoFiltro Infrasonico Interruttore ModalitàCablatura per più amplificatori FunzionamentoAllamplificaTo Amplifier 5 tore 5 ecc. and so on Cavi sincronizzazione bd Funzionamento Interruttore FaseOppure INDIVIDUAZIONE/RIPARAZIONE GuastiAltrimenti continuare Procedura 3Controllare le uscite audio dell’amplificatoreSpecifiche Modello PowerSpecifiche soggette a modiche senza preavviso Informazioni Inerenti Alla Garanzia Limitata Lunghezza della garanzia

T20001 BD, T30001 BD, T10001 BD specifications

Rockford Fosgate has long been a leader in the car audio industry, known for its high-performance amplifiers designed to deliver powerful sound and enhance the overall audio experience in vehicles. Among their impressive lineup, the T10001 BD, T30001 BD, and T20001 BD stand out as some of the most powerful amplifiers available. Each model is engineered with unique features and advanced technologies to provide exceptional audio performance.

The Rockford Fosgate T10001 BD is a class BD monoblock amplifier that offers an outstanding power output of up to 1000 watts RMS at 1 ohm. This amp is equipped with Rockford Fosgate's proprietary Regulated Switch Mode Power Supply (R.S.M.P.S.), which ensures consistent performance, even under extreme load conditions. The T10001 BD features a variable low-pass filter, an adjustable bass boost, and a remote bass control, allowing users to fine-tune their audio to match personal preferences. Additionally, the amplifier has built-in protection circuitry to guard against overheating, short circuits, and DC offset, ensuring reliable operation.

Taking it up a notch is the T30001 BD, delivering an astonishing 3000 watts RMS at 1 ohm. Like the T10001 BD, this model utilizes a class BD topology for superior efficiency and performance. The T30001 BD is equipped with advanced features such as a variable low-pass filter, a fixed high-pass filter, and a parametric bass boost for maximum flexibility. Its compact design allows for easy installation, while the built-in crossover ensures smooth audio reproduction across the frequency spectrum. The amplifier also includes an illuminated logo, adding a touch of style to its robust build.

For those seeking a powerhouse amplifier in a smaller package, the T20001 BD is the perfect choice. This monoblock amplifier offers 2000 watts RMS at 1 ohm, maintaining the high-quality sound and performance found in Rockford Fosgate's other models. The T20001 BD includes features such as a variable low-pass filter, a remote bass control, and built-in protection circuitry. Its small footprint makes for easy integration into various vehicle setups, making it a versatile option for car audio enthusiasts.

In summary, the Rockford Fosgate T10001 BD, T30001 BD, and T20001 BD amplifiers exemplify the brand's commitment to high-quality, powerful audio performance. With advanced technologies such as R.S.M.P.S., variable filters, and comprehensive protection features, these amplifiers are designed to meet the demands of serious car audio enthusiasts and professionals alike.
Top Page Image Contents