Rockford Fosgate T20001 BD, T30001 BD manual Operation PARA-PUNCH Remote Bass, Boost, Mounting Clip

Page 9

OPERATION

PARA-PUNCH REMOTE BASS

Mounting and installation

1. Find a location that gives easy access to the remote.

NOTE:You can mount this unit in a variety of ways. Remove the back housing by using a small flat screwdriver in the slotted hole at the back.The housing can be installed with the mounting tab up or down, or left off for in panel installation.

2. Route the cable for the remote and connect to the amplifier.

Outside Panel Install

3. Using the screws supplied, install the mounting clip.

4. Slip the remote onto the mounting clip until it snaps into place.

5. Connect the cable to the remote.

Panel Install

6. Cut out a 2”x 7/8” hole in the panel, with a maximum panel thickness of

3/8”. Ensure there is enough room within the panel area for connection.

7. Route the cable through the hole and connect to the remote.

8. Press the remote into the panel cutout until it clicks in place.

Operation

9. Left Knob-Bass Boost Control:Turn clockwise to boost amplifier bass frequencies.

:Overexcursion and subsequent CAUTION damage may occur at high levels

of boost

10. Right Knob-Center Frequency Control:

Turn clockwise to select the center frequency desired (35Hz-70Hz).

Mounting Clip

+18

 

 

 

 

 

 

+14

 

 

 

 

 

 

+10

 

 

 

 

 

 

+6

 

 

 

 

 

 

dB +20

 

 

 

 

 

 

-2

30

40

50

70

90

200

20

Hz

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installation Operation Introduction Table of ContentsContents of Carton Safety InstructionsRating. See Specifications for fuse ratings Design FeaturesProt Distortion and increases efficiencyInstallation Considerations InstallationEngine Compartment Mounting LocationsTrunk Mounting Passenger Compartment MountingWiring the System Installation Battery and ChargingCurrent and could induce noise into the audio system Source to activate the amplifierSingle Power Connection Single Amplifier WiringOperation PARA-PUNCH Remote Bass BoostMounting Clip Adjusting Crossover Frequency Operation Adjusting GainMode Switch Infrasonic FilterOperation Multiple Amplifier WiringMaster SlaveBd Sync Wiring Operation Phase SwitchProcedure 1 Check Amplifier for proper connections TroubleshootingProcedure 2 Protect or Thermal light is on Procedure 3 Check Amplifier for audio outputMODEL- Power SpecificationsSpecifications subject to change without notice T30001 bdLimited Warranty Information Length of WarrantyNuméro de modèle Table DES MatièresAvertissement Mise EN Garde Consignes DE SécuritéParticularités Techniques Cette DEL rouge sillumine si lampli atteint le troisièmeCette DEL jaune sillumine si un court-circuit ou une Haut-parleurs Installation Considérations Concernant L’INSTALLATIONEmplacements DE Montage Confiez la tâche à un technicien qualifiéDe dommages à lappareil Votre distributeur agréé Rockford Fosgate Installation Batterie ET ChargeREM à une source positive commutée de 12 volts. La tension Pour activer lampliCauser des blessures ou endommager lampli et/ou les Ces amplis ne sont pas recommandés pour des chargesAvertissement Par paires damplisAttache de fixation Fonctionnement Télécommande DE Basses PARA-PUNCHFonctionnement Réglage DU Gain Sélecteur DE ModeRéglage DE LA Fréquence DU Filtre Passif Filtre InfrasoniqueCâblage pour plusieurs amplis FonctionnementMaître Réglé surCâblage bd Sync Fonctionnement Commutateur DE PhaseSet to Bd SyncDépannage Procédure 2 Le voyant de protection ou thermique est alluméProcédure 3 Vérifiez la sortie audio de lampli Modèle Power CaractéristiquesLes spécifications sont sujettes à changements sans préavis Informations SUR LA Garantie Limitée Durée de la garantieÍndice DE Materias IntroducciónNúmero de la serie Número del modelo NOTALea cada sección para obtener información más detalladaInstrucciones DE Seguridad PrecauciónContenido DE LA Caja LED de temperatura Par La unidadLED de protección Parte superior Distorsión y aumenta la eficienciaInstalación Consideraciones Para LA Instalación Lugares DE Montaje InstalaciónCompartimento del motor Instalación en el maleteroInstalación Bateríay Carga Cableado DEL SistemaVoltios para activar el amplificador Daños al amplificador o a los componentes conectados Broche de montaje Funcionamiento PARA-PUNCH Remote BassInstalación del panel externo Instalación del panelAjuste DE LA Frecuencia X-OVER Transición Funcionamiento Ajuste DE GananciaFiltro Infrasónico Interruptor DE ModoFuncionamiento MaestroEsclavo Cableado de sincronización de db Funcionamiento Interruptor DE FaseEstá encendida vaya al Paso 3,de otra manera,continúe Solución DE ProblemasEspecificaciones Modelo PowerRockford SpeakersAcoustic Design Speaker Returns Información Sobre LA Garantía LimitadaInhaltsverzeichnis EinleitungSeriennummer Modellnummer Einleitung Sicherheitshinweise DesigncharakteristikenDieses Symbol mit dem Wort „VORSICHT soll den Benutzer auf Dieses Symbol mit dem Wort „WARNUNG soll den Benutzer aufSicherheitshinweise Führt zu schweren Verletzungen oder TodDiese rote LED leuchtet auf, wenn der Verstärker die dritte DesigncharakteristikenDesigncharakteristiken Einbau EinbauüberlegungenBefestigungsstellen EinbauMotorraum Einbau im KofferraumEinbau Batterie UND Aufladung Verkabelung DES SystemsVerursachen Angeschlossenen Komponenten verursacht werden Stromzufuhr zum Verstärker abgeschaltet oder entfernt wurdeOder Pro überbrücktem Verstärkerpaar empfohlenBefestigungs Klemme Betrieb PARA-PUNCHBASS-FERNBEDIENUNGBefestigung und Einbau Einbau im ArmaturenbrettCROSSOVER-FREQUENZ Einstellen Betrieb Lautstärke Gain EinstellenInfraschallfilter FunktionsschalterBetrieb Bd-Synchronverkabelung Betrieb PhasenschalterVerfahren 2Schutz- oderThermallicht leuchtet auf FehlerbeseitigungVerfahren 3DenVerstärker aufAudioleistung überprüfen OderTechnische Daten MODELL- PowerT10001 bd Die technischen Daten können sich ohne Ankündigung ändernInformationen ZUR Beschränkten Garantie Laufzeit der GarantieIndice IntroduzioneNumero di serie Numero di modello Nota Ripassare ciascuna sezione per ulteriori ragguagliContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaLED temp Caratteristiche DEL DesignAutomaticamente TerminaliInstallazione Considerazioni SULL’INSTALLAZIONE ComandoInterru Posizionamento InstallazioneScompartimento del motore Montaggio nel bagagliaioInstallazione Batteria E Caricamento Cablaggio DEL SistemaSistema audio Singlesingle Graffa di Montaggio Funzionamento Comando a Distanza PER Toni Bassi PARA-PUNCHRegolazione Della Frequenza DI Incrocio Funzionamento Regolazione DEL GuadagnoFiltro Infrasonico Interruttore ModalitàFunzionamento Cablatura per più amplificatoriAllamplificaTo Amplifier 5 tore 5 ecc. and so on Cavi sincronizzazione bd Funzionamento Interruttore FaseOppure INDIVIDUAZIONE/RIPARAZIONE GuastiAltrimenti continuare Procedura 3Controllare le uscite audio dell’amplificatoreModello Power SpecificheSpecifiche soggette a modiche senza preavviso Informazioni Inerenti Alla Garanzia Limitata Lunghezza della garanzia

T20001 BD, T30001 BD, T10001 BD specifications

Rockford Fosgate has long been a leader in the car audio industry, known for its high-performance amplifiers designed to deliver powerful sound and enhance the overall audio experience in vehicles. Among their impressive lineup, the T10001 BD, T30001 BD, and T20001 BD stand out as some of the most powerful amplifiers available. Each model is engineered with unique features and advanced technologies to provide exceptional audio performance.

The Rockford Fosgate T10001 BD is a class BD monoblock amplifier that offers an outstanding power output of up to 1000 watts RMS at 1 ohm. This amp is equipped with Rockford Fosgate's proprietary Regulated Switch Mode Power Supply (R.S.M.P.S.), which ensures consistent performance, even under extreme load conditions. The T10001 BD features a variable low-pass filter, an adjustable bass boost, and a remote bass control, allowing users to fine-tune their audio to match personal preferences. Additionally, the amplifier has built-in protection circuitry to guard against overheating, short circuits, and DC offset, ensuring reliable operation.

Taking it up a notch is the T30001 BD, delivering an astonishing 3000 watts RMS at 1 ohm. Like the T10001 BD, this model utilizes a class BD topology for superior efficiency and performance. The T30001 BD is equipped with advanced features such as a variable low-pass filter, a fixed high-pass filter, and a parametric bass boost for maximum flexibility. Its compact design allows for easy installation, while the built-in crossover ensures smooth audio reproduction across the frequency spectrum. The amplifier also includes an illuminated logo, adding a touch of style to its robust build.

For those seeking a powerhouse amplifier in a smaller package, the T20001 BD is the perfect choice. This monoblock amplifier offers 2000 watts RMS at 1 ohm, maintaining the high-quality sound and performance found in Rockford Fosgate's other models. The T20001 BD includes features such as a variable low-pass filter, a remote bass control, and built-in protection circuitry. Its small footprint makes for easy integration into various vehicle setups, making it a versatile option for car audio enthusiasts.

In summary, the Rockford Fosgate T10001 BD, T30001 BD, and T20001 BD amplifiers exemplify the brand's commitment to high-quality, powerful audio performance. With advanced technologies such as R.S.M.P.S., variable filters, and comprehensive protection features, these amplifiers are designed to meet the demands of serious car audio enthusiasts and professionals alike.
Top Page Image Contents