Rockford Fosgate T20001 BD, T30001 BD manual Mounting Locations, Engine Compartment, Trunk Mounting

Page 6

INSTALLATION

This section focuses on some of the vehicle considerations for installing your new amplifier. Pre-planning your system layout and best wiring routes will save installation time.When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

:If you feel unsure about installing this system yourself, have it installed by a CAUTION qualified technician.

:Before installation, disconnect the battery negative (-) terminal to prevent CAUTION damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1. Be sure to carefully read and understand the instructions before attempting to install the unit.

2. For safety, disconnect the negative lead from the battery prior to beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting your unit in place.

4. Route all of the RCA cables close together and away from any high current wires.

5. Use high quality connectors for a reliable installation and to minimize signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18" (45.7 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

MOUNTING LOCATIONS

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment will void your warranty.

Trunk Mounting

Mounting the amplifier vertically will provide adequate cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will provide the best cooling of the amplifier.

Mounting the amplifier upside down to the rear deck of the trunk will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as you provide a sufficient amount of air for the amplifier to cool itself. If you are going to mount the amplifier under the seat of the vehicle, you must have at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the amplifier's heatsink in the passenger compartment will not provide proper cooling and will severely affect the performance of the amplifier and is strongly not recommended.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Operation Table of Contents IntroductionSafety Instructions Contents of CartonProt Design FeaturesRating. See Specifications for fuse ratings Distortion and increases efficiencyInstallation Installation ConsiderationsTrunk Mounting Mounting LocationsEngine Compartment Passenger Compartment MountingCurrent and could induce noise into the audio system Installation Battery and ChargingWiring the System Source to activate the amplifierPower Connection Single Amplifier Wiring SingleOperation PARA-PUNCH Remote Bass BoostMounting Clip Mode Switch Operation Adjusting GainAdjusting Crossover Frequency Infrasonic FilterMaster Multiple Amplifier WiringOperation SlaveOperation Phase Switch Bd Sync WiringProcedure 2 Protect or Thermal light is on TroubleshootingProcedure 1 Check Amplifier for proper connections Procedure 3 Check Amplifier for audio outputSpecifications subject to change without notice SpecificationsMODEL- Power T30001 bdLength of Warranty Limited Warranty InformationTable DES Matières Numéro de modèleConsignes DE Sécurité Avertissement Mise EN GardeParticularités Techniques Cette DEL rouge sillumine si lampli atteint le troisièmeCette DEL jaune sillumine si un court-circuit ou une Installation Considérations Concernant L’INSTALLATION Haut-parleursEmplacements DE Montage Confiez la tâche à un technicien qualifiéDe dommages à lappareil REM à une source positive commutée de 12 volts. La tension Installation Batterie ET ChargeVotre distributeur agréé Rockford Fosgate Pour activer lampliAvertissement Ces amplis ne sont pas recommandés pour des chargesCauser des blessures ou endommager lampli et/ou les Par paires damplisFonctionnement Télécommande DE Basses PARA-PUNCH Attache de fixationRéglage DE LA Fréquence DU Filtre Passif Sélecteur DE ModeFonctionnement Réglage DU Gain Filtre InfrasoniqueMaître FonctionnementCâblage pour plusieurs amplis Réglé surSet to Fonctionnement Commutateur DE PhaseCâblage bd Sync Bd SyncDépannage Procédure 2 Le voyant de protection ou thermique est alluméProcédure 3 Vérifiez la sortie audio de lampli Modèle Power CaractéristiquesLes spécifications sont sujettes à changements sans préavis Durée de la garantie Informations SUR LA Garantie LimitéeNúmero de la serie Número del modelo IntroducciónÍndice DE Materias NOTALea cada sección para obtener información más detalladaInstrucciones DE Seguridad PrecauciónContenido DE LA Caja LED de protección Parte superior La unidadLED de temperatura Par Distorsión y aumenta la eficienciaInstalación Consideraciones Para LA Instalación Compartimento del motor InstalaciónLugares DE Montaje Instalación en el maleteroInstalación Bateríay Carga Cableado DEL SistemaVoltios para activar el amplificador Daños al amplificador o a los componentes conectados Instalación del panel externo Funcionamiento PARA-PUNCH Remote BassBroche de montaje Instalación del panelFiltro Infrasónico Funcionamiento Ajuste DE GananciaAjuste DE LA Frecuencia X-OVER Transición Interruptor DE ModoFuncionamiento MaestroEsclavo Funcionamiento Interruptor DE Fase Cableado de sincronización de dbSolución DE Problemas Está encendida vaya al Paso 3,de otra manera,continúeModelo Power EspecificacionesInformación Sobre LA Garantía Limitada Rockford SpeakersAcoustic Design Speaker ReturnsSeriennummer Modellnummer EinleitungInhaltsverzeichnis Einleitung Sicherheitshinweise DesigncharakteristikenSicherheitshinweise Dieses Symbol mit dem Wort „WARNUNG soll den Benutzer aufDieses Symbol mit dem Wort „VORSICHT soll den Benutzer auf Führt zu schweren Verletzungen oder TodDesigncharakteristiken Diese rote LED leuchtet auf, wenn der Verstärker die dritteEinbau Einbauüberlegungen DesigncharakteristikenMotorraum EinbauBefestigungsstellen Einbau im KofferraumEinbau Batterie UND Aufladung Verkabelung DES SystemsVerursachen Oder Stromzufuhr zum Verstärker abgeschaltet oder entfernt wurdeAngeschlossenen Komponenten verursacht werden Pro überbrücktem Verstärkerpaar empfohlenBefestigung und Einbau Betrieb PARA-PUNCHBASS-FERNBEDIENUNGBefestigungs Klemme Einbau im ArmaturenbrettInfraschallfilter Betrieb Lautstärke Gain EinstellenCROSSOVER-FREQUENZ Einstellen FunktionsschalterBetrieb Betrieb Phasenschalter Bd-SynchronverkabelungVerfahren 3DenVerstärker aufAudioleistung überprüfen FehlerbeseitigungVerfahren 2Schutz- oderThermallicht leuchtet auf OderT10001 bd MODELL- PowerTechnische Daten Die technischen Daten können sich ohne Ankündigung ändernLaufzeit der Garantie Informationen ZUR Beschränkten GarantieNumero di serie Numero di modello IntroduzioneIndice Nota Ripassare ciascuna sezione per ulteriori ragguagliIstruzioni DI Sicurezza Contenuto DELL’IMBALLAGGIOAutomaticamente Caratteristiche DEL DesignLED temp TerminaliInstallazione Considerazioni SULL’INSTALLAZIONE ComandoInterru Scompartimento del motore InstallazionePosizionamento Montaggio nel bagagliaioInstallazione Batteria E Caricamento Cablaggio DEL SistemaSistema audio Singlesingle Funzionamento Comando a Distanza PER Toni Bassi PARA-PUNCH Graffa di MontaggioFiltro Infrasonico Funzionamento Regolazione DEL GuadagnoRegolazione Della Frequenza DI Incrocio Interruttore ModalitàFunzionamento Cablatura per più amplificatoriAllamplificaTo Amplifier 5 tore 5 ecc. and so on Funzionamento Interruttore Fase Cavi sincronizzazione bdAltrimenti continuare INDIVIDUAZIONE/RIPARAZIONE GuastiOppure Procedura 3Controllare le uscite audio dell’amplificatoreModello Power SpecificheSpecifiche soggette a modiche senza preavviso Lunghezza della garanzia Informazioni Inerenti Alla Garanzia Limitata

T20001 BD, T30001 BD, T10001 BD specifications

Rockford Fosgate has long been a leader in the car audio industry, known for its high-performance amplifiers designed to deliver powerful sound and enhance the overall audio experience in vehicles. Among their impressive lineup, the T10001 BD, T30001 BD, and T20001 BD stand out as some of the most powerful amplifiers available. Each model is engineered with unique features and advanced technologies to provide exceptional audio performance.

The Rockford Fosgate T10001 BD is a class BD monoblock amplifier that offers an outstanding power output of up to 1000 watts RMS at 1 ohm. This amp is equipped with Rockford Fosgate's proprietary Regulated Switch Mode Power Supply (R.S.M.P.S.), which ensures consistent performance, even under extreme load conditions. The T10001 BD features a variable low-pass filter, an adjustable bass boost, and a remote bass control, allowing users to fine-tune their audio to match personal preferences. Additionally, the amplifier has built-in protection circuitry to guard against overheating, short circuits, and DC offset, ensuring reliable operation.

Taking it up a notch is the T30001 BD, delivering an astonishing 3000 watts RMS at 1 ohm. Like the T10001 BD, this model utilizes a class BD topology for superior efficiency and performance. The T30001 BD is equipped with advanced features such as a variable low-pass filter, a fixed high-pass filter, and a parametric bass boost for maximum flexibility. Its compact design allows for easy installation, while the built-in crossover ensures smooth audio reproduction across the frequency spectrum. The amplifier also includes an illuminated logo, adding a touch of style to its robust build.

For those seeking a powerhouse amplifier in a smaller package, the T20001 BD is the perfect choice. This monoblock amplifier offers 2000 watts RMS at 1 ohm, maintaining the high-quality sound and performance found in Rockford Fosgate's other models. The T20001 BD includes features such as a variable low-pass filter, a remote bass control, and built-in protection circuitry. Its small footprint makes for easy integration into various vehicle setups, making it a versatile option for car audio enthusiasts.

In summary, the Rockford Fosgate T10001 BD, T30001 BD, and T20001 BD amplifiers exemplify the brand's commitment to high-quality, powerful audio performance. With advanced technologies such as R.S.M.P.S., variable filters, and comprehensive protection features, these amplifiers are designed to meet the demands of serious car audio enthusiasts and professionals alike.
Top Page Image Contents