Pioneer AVIC-N3 installation manual Installation

Page 18

Installation

•Pioneer does not recommend that you install or service your navigation sys- tem yourself. Installing or servicing the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your navigation system to authorized Pioneer service personnel.

•Never install this product in places, or in a manner that where:

*It could injure the driver or passengers if the vehicle stops suddenly.

*It may interfere with the driver’s operation of the vehicle, such as on the floor in front of the driver’s seat, or close to the steering wheel or shift lever.

•Make sure there is nothing behind the dashboard or paneling when drilling holes in them. Be careful not to damage fuel lines, brake lines, electronic components, communication wires or power cables.

•When using screws, do not allow them to come into contact with any electri- cal lead. Vibration may damage wires or insulation, leading to a short circuit or other damage to the vehicle.

•To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of this product or they may work loose and the product may become detached.

•It is extremely dangerous to allow the GPS antenna lead or microphone lead to become wound around the steering column or shift lever. Be sure to install this product in such a way that it will not obstruct driving.

•Make sure that leads cannot get caught in a door or the sliding mechanism of a seat, resulting in a short circuit.

•Please confirm the proper function of your vehicle’s other equipment follow- ing installation of the navigation system.

•Certain government laws may prohibit or restrict the placement and use of this system in your vehicle. Please comply with all applicable laws and regu- lations regarding the use, installation and operation of your navigation sys- tem.

•Do not install the display unit or Hide-away unit where it may (i) obstruct the driver’s vision, (ii) impair the performance of any of the vehicle’s operat-

ing systems or safety features, including airbags, hazard lamp buttons or (iii)

17impair the driver’s ability to safely operate the vehicle.

Image 18

Contents Installation Manual Important Information Contents Important Safeguards Connecting the System Before installing this product To prevent damageParts supplied Connecting the system Dock connectorDeutsch Français Italiano Nederlands Connecting the power cord ON/OFFGuide on Pink CAR Speed Signal Input Yellow/black Guide on When connecting to separately sold power amp NON-FADING Output Deutsch Français When connecting a Rear view camera When connecting the external video component and the display When using a display connected to rear video outputInstallation Before installing To guard against electromagnetic interferenceInstalling the display unit and Hide-away unit Installation notesDo not cover these areas Binding screw Flush surface screw Installing the Hide-away unit Attach the side brackets to the Hide-away unitDecide on the installation position, and drill the holes Secure it firmly using the self-tapping screwsDIN Front-mount Install the display unit into DashboardDIN Front/Rear-mount Remove the frame and the holderDIN Rear-mount Fixing the front panelInstalling the GPS antenna GPS antenna Metal sheet Clamp 5 pcs When installing the antenna outside the vehicle on the body When routing the lead in from the top of the doorWhen routing the lead in from inside the trunk Start the engine Press the Reset button on the display unit After Installing this ProductReconnecting the battery Enter the following settingsEnglish Español Deutsch Français Italiano Nederlands Information Importante Sommaire Importantes Mesures DEImportantes Mesures DE Securite Branchement du système Avant de raccorder ce produit Pour éviter des dégâtsPièces fournies Branchement du système Remarque Branchement du cordon d’alimentation GaucheEnglish Français Deutsch Français Italiano Vert clair Français Rear Output English Pour relier ce produit avec une caméra de rétrovisée Pour relier l’appareil vidéo externe et l’affichage Pour utiliser un écran branché à la sortie vidéo arrièreInstallation Avant de procéder à l’installation Installation de l’unité d’affichage et de l’unité déportée Remarques sur l’installationFrançais Deutsch Français Italiano Nederlands Vis de pression Vis à tête plate Installation de l’unité déportée Fixez les supports latéraux sur l’unité déportéeChoisissez la position d’installation, et percez les trous Montage DIN avant Installez l’unité d’affichage sur Le tableau de bordMontage DIN avant/arrière Retirez le cadre et le supportMontage DIN arrière Fixation du panneau avantInstallation de l’antenne GPS Antenne GPS Plaque métallique Serre-fils 5 pièces Cheminement du câble sur le haut de la portière Cheminement du fil par l’intérieur du coffreAprès installation de ce produit Branchement de la batterieEntrez les réglages suivants Pioneer Corporation