Pioneer AVIC-N3 To guard against electromagnetic interference, Before installing

Page 19

Install the display unit between the driver’s seat and front passenger seat so that it will not be hit by the driver or passenger if the vehicle stops quickly.

Never install the display unit in front of or next to the place in the dash, door, or pillar from which one of your vehicle’s airbags would deploy. Please refer to your vehicle’s Owner’s Manual for reference to the deployment area of the frontal airbags.

Do not install the display unit and Hide-away unit in a place where it will impair the performance of any of the vehicle’s operating systems, including airbags and headrests.

To guard against electromagnetic interference

In order to prevent interference, set the following items as far as possible from the dis- play unit and Hide-away unit of this navigation system, other cables or leads:

-TV antenna and antenna lead

-FM, AM antenna and its lead

-GPS antenna and its lead

In addition you should lay or route each antenna lead as far as possible from other antenna leads.

Do not bind them together, lay or route them together, or cross them.

Such electromagnetic noise will increase the potential for errors in the location display.

Before installing

Consult with your nearest dealer if installation requires the drilling of holes or other mod- ifications of the vehicle.

Before making a final installation of this product, temporarily connect the wiring to con- firm that the connections are correct and the system works properly.

English

Español

Deutsch Français Italiano

Nederlands

18

Image 19
Contents Installation Manual Important Information Contents Important Safeguards Connecting the System To prevent damage Before installing this productParts supplied Dock connector Connecting the systemDeutsch Français Italiano Nederlands ON/OFF Connecting the power cordGuide on Pink CAR Speed Signal Input Yellow/black Guide on NON-FADING Output When connecting to separately sold power ampDeutsch Français When connecting a Rear view camera When using a display connected to rear video output When connecting the external video component and the displayInstallation To guard against electromagnetic interference Before installingInstallation notes Installing the display unit and Hide-away unitDo not cover these areas Binding screw Flush surface screw Attach the side brackets to the Hide-away unit Installing the Hide-away unitSecure it firmly using the self-tapping screws Decide on the installation position, and drill the holesRemove the frame and the holder Install the display unit into DashboardDIN Front/Rear-mount DIN Front-mountFixing the front panel DIN Rear-mountInstalling the GPS antenna GPS antenna Metal sheet Clamp 5 pcs When routing the lead in from the top of the door When installing the antenna outside the vehicle on the bodyWhen routing the lead in from inside the trunk Enter the following settings After Installing this ProductReconnecting the battery Start the engine Press the Reset button on the display unitEnglish Español Deutsch Français Italiano Nederlands Information Importante Importantes Mesures DE SommaireImportantes Mesures DE Securite Branchement du système Pour éviter des dégâts Avant de raccorder ce produitPièces fournies Branchement du système Remarque Gauche Branchement du cordon d’alimentationEnglish Français Deutsch Français Italiano Vert clair Français Rear Output English Pour relier ce produit avec une caméra de rétrovisée Pour utiliser un écran branché à la sortie vidéo arrière Pour relier l’appareil vidéo externe et l’affichageInstallation Avant de procéder à l’installation Remarques sur l’installation Installation de l’unité d’affichage et de l’unité déportéeFrançais Deutsch Français Italiano Nederlands Vis de pression Vis à tête plate Fixez les supports latéraux sur l’unité déportée Installation de l’unité déportéeChoisissez la position d’installation, et percez les trous Retirez le cadre et le support Installez l’unité d’affichage sur Le tableau de bordMontage DIN avant/arrière Montage DIN avantFixation du panneau avant Montage DIN arrièreInstallation de l’antenne GPS Antenne GPS Plaque métallique Serre-fils 5 pièces Cheminement du fil par l’intérieur du coffre Cheminement du câble sur le haut de la portièreBranchement de la batterie Après installation de ce produitEntrez les réglages suivants Pioneer Corporation