Pioneer AVIC-N3 installation manual Installing the GPS antenna, Installation notes

Page 27

Installing the GPS antenna

Do not cut the GPS antenna lead to shorten it or use an extension to make it longer. Altering the antenna cable could result in a short circuit or malfunc- tion and permanent damage to the product.

Installation notes

English

The antenna should be installed on a

level surface where radio waves will be blocked as little as possible. Radio waves cannot be received by the anten- na if reception from the satellite is blocked.

Installation on the vehicle roof or trunk lid is recommended to optimise recep- tion.

Roof

Trunk lid

Rear shelf

Español

Deutsch

When installing the GPS antenna inside the vehicle, be sure to use the metal sheet pro- vided with your system. If this is not used, the reception sensitivity will be poor.

Do not cut the accessory metal sheet. This would reduce the sensitivity of the GPS antenna.

Take care not to pull the antenna lead when removing the GPS antenna. The magnet attached to the antenna is very powerful, and the lead may become detached.

The GPS antenna is installed with a magnet. When installing the GPS antenna, be care- ful not to scratch the vehicle body.

When installing the GPS antenna on the outside of the vehicle, always put it in the vehi- cle when going through an automatic vehicle wash. If it is left on the outside it may be knocked off and scratch the vehicle body.

Do not paint the GPS antenna, as this may affect its performance.

Français Italiano

Nederlands

26

Image 27
Contents Installation Manual Important Information Contents Important Safeguards Connecting the System To prevent damage Before installing this productParts supplied Dock connector Connecting the systemDeutsch Français Italiano Nederlands ON/OFF Connecting the power cordGuide on Pink CAR Speed Signal Input Yellow/black Guide on NON-FADING Output When connecting to separately sold power ampDeutsch Français When connecting a Rear view camera When using a display connected to rear video output When connecting the external video component and the displayInstallation To guard against electromagnetic interference Before installingInstallation notes Installing the display unit and Hide-away unitDo not cover these areas Binding screw Flush surface screw Attach the side brackets to the Hide-away unit Installing the Hide-away unitSecure it firmly using the self-tapping screws Decide on the installation position, and drill the holesRemove the frame and the holder Install the display unit into DashboardDIN Front/Rear-mount DIN Front-mountFixing the front panel DIN Rear-mountInstalling the GPS antenna GPS antenna Metal sheet Clamp 5 pcs When installing the antenna outside the vehicle on the body When routing the lead in from the top of the doorWhen routing the lead in from inside the trunk Enter the following settings After Installing this ProductReconnecting the battery Start the engine Press the Reset button on the display unitEnglish Español Deutsch Français Italiano Nederlands Information Importante Importantes Mesures DE SommaireImportantes Mesures DE Securite Branchement du système Pour éviter des dégâts Avant de raccorder ce produitPièces fournies Branchement du système Remarque Gauche Branchement du cordon d’alimentationEnglish Français Deutsch Français Italiano Vert clair Français Rear Output English Pour relier ce produit avec une caméra de rétrovisée Pour utiliser un écran branché à la sortie vidéo arrière Pour relier l’appareil vidéo externe et l’affichageInstallation Avant de procéder à l’installation Remarques sur l’installation Installation de l’unité d’affichage et de l’unité déportéeFrançais Deutsch Français Italiano Nederlands Vis de pression Vis à tête plate Fixez les supports latéraux sur l’unité déportée Installation de l’unité déportéeChoisissez la position d’installation, et percez les trous Retirez le cadre et le support Installez l’unité d’affichage sur Le tableau de bordMontage DIN avant/arrière Montage DIN avantFixation du panneau avant Montage DIN arrièreInstallation de l’antenne GPS Antenne GPS Plaque métallique Serre-fils 5 pièces Cheminement du fil par l’intérieur du coffre Cheminement du câble sur le haut de la portièreAprès installation de ce produit Branchement de la batterieEntrez les réglages suivants Pioneer Corporation