Pentair Intellitouch ScreenLogic manual IntelliFlo Alarms and Warnings, Suction Blockage

Page 103

93

IntelliFlo Alarms and Warnings

The IntelliFlo displays all alarms and warnings on the control panel display. When an alarm or warning condition exists, the corresponding LED will be lit on the display. All control panel buttons are disabled until the alarm or warning is acknowledged with the Enter button. Press the Reset button to clear the alarm once the fault condition has been resolved. Note: The IntelliFlo pump will not start if the impeller is rotating. The alerts and warnings are:

•Power out failure: The incoming supply voltage is less than 170 VAC. The drive faults to protect itself from over current. The drive contains capacitors that keep it powered up long enough to save the current run parameters. If power is restored during this process, approximately 20 seconds, the drive will not restart until completed.

•Priming error: If the pump is not defined as primed within the "Max Priming Time" it will stop and generate a “Priming Alarm” for 10 minutes, then attempt to prime again. The "Max Priming Time" is set by the user on the priming menu as discussed on page 14. If the IntelliFlo cannot prime within five attempts it will generate a permanent alarm that must be manually reset.

•Overheat alert: If the drive temperature gets above 130 degrees, the IntelliFlo will slowly reduce speed until the over temperature condition clears.

•Anti-freezing:When active, the motor will run at 1000 rpm for 60 minutes. Only active in Filter and

Manual modes. Note: The IntelliFlo's internal anti-freeze protection is disabled when connected to an IntelliTouch system. Freeze protection is provided by selecting YES at the ON WITH FREEZE portion of the IntelliTouch's appropriate circuit function menu. To re-enable the IntelliFlo's internal anti-freeze protection, the power to the drive must be cycled off then back on.

•Blocked system: Detects a blocked suction line. This alarm resets automatically after 30 seconds and the pump restarts.

•System service soon: Alerts the operator that the pump discharge pressure has reached the Clean Filter Pressure as setup in the Filter Menu. The filter status will be displayed as 100%. The yellow warning LED will be on until a backwash cycle is operated. The IntelliFlo will automatically reduce speed as necessary to not exceed the Clean Filter Pressure.

•Over current: Indicated that the drive is overloaded or the motor has an electrical problem. The drive will restart 20 seconds after the over current condition clears.

•Over voltage: Indicates excessive supply voltage or an external water source is causing the pump and motor to rotate thereby generating an excessive voltage on the drives internal DC bus. The drive will restart 20 seconds after the over voltage condition clears.

For IntelliFlo troubleshooting information, see the IntelliFlo 4 Installation and User’s Guide (P/N 350075).

Suction Blockage

When something blocks the suction or the pump fully it will shut off immediately (within 1 second). It will also shut off after a few seconds of dead heading with the same alert. The unit will come back on in 30 seconds and ramp up slowly. This function should be tested with all new installations by directing the flow to one suction and covering it with a piece of material other than someone’s hand. This alert is deactivated in Manual mode.

IntelliTouch ScreenLogic User’s Guide

Page 102 Page 104
Image 103
Page 102 Page 104
Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Frequently Asked Questions FAQs and Troubleshooting Using ScreenLogicGlossary 102 AppendixImportant Safety Precautions Important Safety Precautions Vii Technical Support About this User’s GuideRelated IntelliTouch Manuals IntelliTouch System Overview IntroductionIntelliTouch System Components Load or Power CenterIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch Interface ScreenLogic Kits IntelliTouch ScreenLogic Interface Accessory KitsBlank PDA, in-Wall Touch Screen Tablet Overview PDA Front and Side Views Personal Digital Assistant PDA DescriptionPDA Rear View In-Wall Touch Screen Controls In-Wall Touch ScreenTablet Controls and Lights Tablet OverviewTablet Lights Tablet FunctionsSave System Settings Tablet and In-Wall Touch Screen Using your ScreenLogic InterfaceImportant Precautions Tablet, PDA, and In-wall Touch Screen Cold Boot/Power On-Off/Reset PDABattery and Power Management PDA Low Battery Condition Tablet and PDAPower on and OFF Tablet and PDA Battery and Power Management TabletInstallation Tools Required Before You BeginConnection Steps Summary ScreenLogic Location Requirements Less walls and ceilings equals better wireless receptionLocation Requirements Cable Distance Limits Recommended Wireless Router and Protocol adapter LocationProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to an existing home network Connecting to your Home Network with Broadband AccessRJ11 for DSL Coax for Cable Proceed to Connect to the Personality Board, Connect to the Protocol AdapterConnecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Start ScreenLogic Program Start the Configurator Utility on the PDATransfer Time from the Configurator Utility Compatibility with IntelliTouch SystemsGeneral Settings ScreenLogic Configuration and Maintenance ScreenName Description Changing the Display to Show Fahrenheit to Celsius Calibrating Temperature SensorsSetup Circuits Special Lights Button Feature Circuit Configuration ButtonFreeze Protection Feature Macro Circuits OverviewAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro Display a Circuit Function Button on the Main Screen Creating Custom Names for Auxiliary CircuitsIntelliTouch Indoor Control Panel Circuit Names Circuits Assigned to Valve Assign a circuit to a valve Configure Other EquipmentPump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up a Two-Speed Pump Setting up Additional EquipmentSet a Cool-Down Cycle for the Heater Setup Solar Equipment and Heat pump optionChlorine Generator Enable Manual Spa Heat ControlActivate the Chlorinator Control Interface Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Pool/Spa heat controls The Heat Main ScreenSource Configuring Pool and Spa Heating System Options Main Lights Screen Change the Pool and Spa TemperatureChanging Pool Heat Settings Changing Spa Heat SettingsColor Lights Tab Dim Lights Lights ScreenSpecial Lighting Features Name Description Lights Screen Configure Set Colors Tab Color SetLights Screen Configure Swimming Colors Tab Set up Swimming Colors Color Swim Color Set Lighting FeatureColor Sync Switching Lights All on/All offColor light show and fixed color buttons Lights Screen IntelliBriteSave and Recall buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen System Delay Cancel Feature System Error MessagesEnable/Disable Spa-Side Remotes Chlorinator Status and Controls Screen Equipment Chlorinator ScreenIntelliFlo Status and IntelliFlo Controls Screen Equipment IntelliFlo ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for details IntelliFlo Status and IntelliFlo 4x160 Controls ScreenBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Technical Support Questions ScreenLogic Tips and FAQsTo enter wireless settings for the Tablet ScreenLogic Error MessagesIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide How can I calibrate the PDA screen? PDA Tips and FAQsStarting Up the Tablet PDA On/Off Button Turn off Backlight Is there anything I need to assemble before I turn it on? Do I need to load any software to get started?How do I make the panel brighter/darker? Connecting Please Wait messageHow do I switch the Tablet off? My Digital Tablet will not switch onTablet comes with a desktop cradle what are its functions? Cleaning the Touch ScreenSuction Blockage IntelliFlo Alarms and WarningsAlarm and warnings LED sequence IntelliFlo 4x160 Alarm and WarningsAppendix Range Extender Kit Description Load Center to Protocol Adapter wireless connection diagram ScreenLogic Wireless Connection KitConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C
Top Page Image Contents