Pentair Intellitouch ScreenLogic manual Configuring Valve Actuators

Page 55

45

Configuring Valve Actuators

To assign a valve actuator:

1.Start the ScreenLogic Configurator and tap Configure IntelliTouch.

2.Tap Next on the General Setting page and on the Setup Circuits page. The Configure Other Equipment (Step 3 of 5) page is displayed.

3.Select the Load Center or Expansion Center(s) and the AUX valve actuator (A, B) you wish to configure from the Valve Assignments list.

Note: When using solar heat, note that for shared equipment pool and spa combination, valve A is always used for solar. For dual body dual equipment, valve A is always the pool and valve B is always the spa.

Valve A: Can be used for solar heating or auxiliary valve actuator control. If the “Solar present” check box is selected “USED BY SOLAR” is displayed in the Valve assignment list. ValveAis automatically configured as a solar heating valve actuator.

Valve B: Can be configured to be controlled by any circuit. Resides on the Personality board.

Valves C D E: Reside on the optional Valve Module board (P/N 520285) that is plugged into the Personality board.

4.In the Circuit Assigned to Valve box, select the circuit that you would like to use to control the valve actuator.

5.Repeat steps 3 and 4 for each valve actuator.

6.Tap Finish when done.

IntelliTouch ScreenLogic User’s Guide

Image 55

Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Frequently Asked Questions FAQs and Troubleshooting Using ScreenLogicGlossary 102 AppendixImportant Safety Precautions Important Safety Precautions Vii Technical Support About this User’s GuideRelated IntelliTouch Manuals IntelliTouch System Overview IntroductionIntelliTouch System Components Load or Power CenterIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch Interface ScreenLogic Kits IntelliTouch ScreenLogic Interface Accessory KitsBlank PDA, in-Wall Touch Screen Tablet Overview PDA Front and Side Views Personal Digital Assistant PDA DescriptionPDA Rear View In-Wall Touch Screen Controls In-Wall Touch ScreenTablet Controls and Lights Tablet OverviewTablet Lights Tablet FunctionsSave System Settings Tablet and In-Wall Touch Screen Using your ScreenLogic InterfaceImportant Precautions Tablet, PDA, and In-wall Touch Screen Cold Boot/Power On-Off/Reset PDABattery and Power Management PDA Low Battery Condition Tablet and PDAPower on and OFF Tablet and PDA Battery and Power Management TabletInstallation Tools Required Before You BeginConnection Steps Summary ScreenLogic Location Requirements Less walls and ceilings equals better wireless receptionLocation Requirements Cable Distance Limits Recommended Wireless Router and Protocol adapter LocationProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to an existing home network Connecting to your Home Network with Broadband AccessRJ11 for DSL Coax for Cable Proceed to Connect to the Personality Board, Connect to the Protocol AdapterConnecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Start ScreenLogic Program Start the Configurator Utility on the PDATransfer Time from the Configurator Utility Compatibility with IntelliTouch SystemsGeneral Settings ScreenLogic Configuration and Maintenance ScreenName Description Changing the Display to Show Fahrenheit to Celsius Calibrating Temperature SensorsSetup Circuits Special Lights Button Feature Circuit Configuration ButtonFreeze Protection Feature Macro Circuits OverviewAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro Display a Circuit Function Button on the Main Screen Creating Custom Names for Auxiliary Circuits IntelliTouch Indoor Control Panel Circuit Names Circuits Assigned to Valve Assign a circuit to a valve Configure Other EquipmentPump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up a Two-Speed Pump Setting up Additional EquipmentSet a Cool-Down Cycle for the Heater Setup Solar Equipment and Heat pump optionChlorine Generator Enable Manual Spa Heat ControlActivate the Chlorinator Control Interface Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Pool/Spa heat controls The Heat Main ScreenSource Configuring Pool and Spa Heating System Options Main Lights Screen Change the Pool and Spa TemperatureChanging Pool Heat Settings Changing Spa Heat SettingsColor Lights Tab Dim Lights Lights ScreenSpecial Lighting Features Name Description Lights Screen Configure Set Colors Tab Color SetLights Screen Configure Swimming Colors Tab Set up Swimming Colors Color Swim Color Set Lighting FeatureColor Sync Switching Lights All on/All offColor light show and fixed color buttons Lights Screen IntelliBriteSave and Recall buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen System Delay Cancel Feature System Error MessagesEnable/Disable Spa-Side Remotes Chlorinator Status and Controls Screen Equipment Chlorinator ScreenIntelliFlo Status and IntelliFlo Controls Screen Equipment IntelliFlo ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for details IntelliFlo Status and IntelliFlo 4x160 Controls ScreenBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Technical Support Questions ScreenLogic Tips and FAQsTo enter wireless settings for the Tablet ScreenLogic Error MessagesIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide How can I calibrate the PDA screen? PDA Tips and FAQsStarting Up the Tablet PDA On/Off Button Turn off BacklightIs there anything I need to assemble before I turn it on? Do I need to load any software to get started?How do I make the panel brighter/darker? Connecting Please Wait messageHow do I switch the Tablet off? My Digital Tablet will not switch onTablet comes with a desktop cradle what are its functions? Cleaning the Touch ScreenSuction Blockage IntelliFlo Alarms and WarningsAlarm and warnings LED sequence IntelliFlo 4x160 Alarm and WarningsAppendix Range Extender Kit Description Load Center to Protocol Adapter wireless connection diagram ScreenLogic Wireless Connection KitConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C