Pentair Intellitouch ScreenLogic manual Glossary

Page 113

103

Glossary (continued)

Load Center: Metal enclosure with power relays, transformer, and circuit breakers. The Load Center is Installed prior to Personality Kit installation. Used for distributing power for controlling IntelliTouch Systems. Also known as the “sub-panel.”

Low Voltage Compartment: Top compartment of Load Center for all low voltage wiring.

Low Voltage Raceway: Vertical space in the left side of Power/Load Center for low voltage cabling.

Megabits-per-second ( Mbps): Transmission speed of 1,000,000 bits per second.

Megahertz (MHz): A unit of frequency equal to 1,000,000 cycles per second.

MobileTouch Controller: Wireless controller for the IntelliTouch Systems with all the functionality of the Indoor Control Panel.

Outdoor Control Panel: Control panel with flexible hinge installed in upper portion of Power/Load Center to control IntelliTouch systems.

Personality Board: The circuit board mounted on top of the Outdoor Control Panel motherboard. The Personality board defines the system capabilities.

Personality Kit: Set of parts to define the capability of a system; may include: Outdoor Control Panel, temperature sensors, actuators, and additional relays.

Power Center: Same as Load Center with the exception of the circuit breaker base.

Relay Circuits: The circuits that control the relays on the Personality Board. Connectors on top edge of the circuit board.

RF: Radio Frequency.

Screw Terminal Connector: Removable connector that may attach to circuit board with multiple sockets (anywhere from 2 to 12) to receive wires from controllers and sensors; wires held by screw terminals; multiple wires of a small enough gauge (usually 22 AWG) may be coupled to a single socket of a terminal connector.

SSID: Service Set Identifier. A value that controls access to a wireless network. The SSID for your wireless network card must match the SSID for any Access Point that you want to connect with. If the value does not match, you are not granted access to the network.

Transceiver: Circuit board with attached antenna that can send and receive radio frequency (wireless) transmissions.

WEP: Wired Equivalent Privacy is a 64 bit and 128 bit (64 bit is sometimes referred to as 40 bit) encryption protocol. WEP aims to provide security by encrypting data over radio waves so that it is protected as it is transmitted from one end point to another.

Wi-Fi:Wireless Fidelity is meant to be used generically when referring of any type of 802.11 network, whether 802.11b, 802.11g, 802.11a. A seal of approval from the Wireless Ethernet Compatibility Alliance (WECA).

WLAN: Wireless Local Area Network is a type of local-area network that uses high-frequency radio waves rather than wires to communicate between nodes.

IntelliTouch ScreenLogic User’s Guide

Image 113
Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Frequently Asked Questions FAQs and Troubleshooting Using ScreenLogicGlossary 102 AppendixImportant Safety Precautions Important Safety Precautions Vii Related IntelliTouch Manuals About this User’s GuideTechnical Support IntelliTouch System Overview IntroductionIntelliTouch System Components Load or Power CenterIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch Interface ScreenLogic Kits IntelliTouch ScreenLogic Interface Accessory KitsBlank PDA, in-Wall Touch Screen Tablet Overview PDA Front and Side Views Personal Digital Assistant PDA DescriptionPDA Rear View In-Wall Touch Screen Controls In-Wall Touch ScreenTablet Controls and Lights Tablet OverviewTablet Lights Tablet FunctionsImportant Precautions Tablet, PDA, and In-wall Touch Screen Using your ScreenLogic InterfaceCold Boot/Power On-Off/Reset PDA Save System Settings Tablet and In-Wall Touch ScreenPower on and OFF Tablet and PDA Low Battery Condition Tablet and PDABattery and Power Management Tablet Battery and Power Management PDAInstallation Connection Steps Summary Before You BeginTools Required ScreenLogic Location Requirements Less walls and ceilings equals better wireless receptionLocation Requirements Cable Distance Limits Recommended Wireless Router and Protocol adapter LocationProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to an existing home network Connecting to your Home Network with Broadband AccessRJ11 for DSL Coax for Cable Proceed to Connect to the Personality Board, Connect to the Protocol AdapterConnecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Transfer Time from the Configurator Utility Start the Configurator Utility on the PDACompatibility with IntelliTouch Systems Start ScreenLogic ProgramGeneral Settings ScreenLogic Configuration and Maintenance ScreenName Description Changing the Display to Show Fahrenheit to Celsius Calibrating Temperature SensorsSetup Circuits Special Lights Button Feature Circuit Configuration ButtonFreeze Protection Feature Macro Circuits OverviewAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro IntelliTouch Indoor Control Panel Circuit Names Creating Custom Names for Auxiliary CircuitsDisplay a Circuit Function Button on the Main Screen Circuits Assigned to Valve Assign a circuit to a valve Configure Other EquipmentPump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up a Two-Speed Pump Setting up Additional EquipmentSet a Cool-Down Cycle for the Heater Setup Solar Equipment and Heat pump optionActivate the Chlorinator Control Interface Enable Manual Spa Heat ControlChlorine Generator Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Pool/Spa heat controls The Heat Main ScreenSource Configuring Pool and Spa Heating System Options Changing Pool Heat Settings Change the Pool and Spa TemperatureChanging Spa Heat Settings Main Lights ScreenColor Lights Tab Dim Lights Lights ScreenSpecial Lighting Features Name Description Lights Screen Configure Set Colors Tab Color SetLights Screen Configure Swimming Colors Tab Set up Swimming Colors Color Swim Color Set Lighting FeatureColor Sync Switching Lights All on/All offSave and Recall buttons Lights Screen IntelliBriteColor light show and fixed color buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen Enable/Disable Spa-Side Remotes System Error MessagesSystem Delay Cancel Feature Chlorinator Status and Controls Screen Equipment Chlorinator ScreenIntelliFlo Status and IntelliFlo Controls Screen Equipment IntelliFlo ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for details IntelliFlo Status and IntelliFlo 4x160 Controls ScreenBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Technical Support Questions ScreenLogic Tips and FAQsTo enter wireless settings for the Tablet ScreenLogic Error MessagesIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide Starting Up the Tablet PDA Tips and FAQsPDA On/Off Button Turn off Backlight How can I calibrate the PDA screen?Is there anything I need to assemble before I turn it on? Do I need to load any software to get started?How do I switch the Tablet off? Connecting Please Wait messageMy Digital Tablet will not switch on How do I make the panel brighter/darker?Tablet comes with a desktop cradle what are its functions? Cleaning the Touch ScreenSuction Blockage IntelliFlo Alarms and WarningsAlarm and warnings LED sequence IntelliFlo 4x160 Alarm and WarningsAppendix Range Extender Kit Description Load Center to Protocol Adapter wireless connection diagram ScreenLogic Wireless Connection KitConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C

Intellitouch ScreenLogic specifications

Pentair Intellitouch ScreenLogic is a cutting-edge control system designed for pool and spa automation, delivering enhanced convenience and efficiency for homeowners. This innovative system allows users to control and manage their swimming pool and spa features through a user-friendly interface, providing comprehensive management from both local and remote locations.

One of the standout features of Intellitouch ScreenLogic is its intuitive touchscreen interface. Users can easily navigate through various settings and functionalities, ensuring a hassle-free experience when adjusting pool temperatures, controlling lights, and managing water features. The interface is designed to be visually appealing and straightforward, accommodating both tech-savvy individuals and those who might find technology overwhelming.

The system's connectivity options are another significant advantage. Intellitouch ScreenLogic integrates seamlessly with a variety of devices, including smartphones and tablets, through the ScreenLogic2 app. This feature allows users to control their pool systems anytime, anywhere, providing unparalleled remote access. Whether you want to heat the spa before arriving home or change the lighting for an evening gathering, the app allows you to manage all aspects effortlessly.

Enhancing customization, Intellitouch ScreenLogic supports various automation options, which can be tailored to meet individual preferences. Homeowners can set schedules for cleaning systems, heating, and lighting, allowing for energy-efficient management. This automation not only adds convenience but also contributes to reducing energy consumption and operational costs.

Furthermore, Pentair's advanced technologies extend beyond simple controls. The system can monitor water quality and provide alerts regarding chemical levels, ensuring that pools remain safe and hygienic. Additionally, the integration of energy-efficient components, such as variable-speed pumps and LED lighting, optimizes energy use, leading to further savings.

In summary, Pentair Intellitouch ScreenLogic stands as a leading solution in pool and spa automation, boasting a user-friendly touchscreen interface, robust remote connectivity, customizable automation features, and advanced monitoring technologies. By investing in this innovative system, pool owners can enjoy enhanced convenience, efficiency, and peace of mind, making pool maintenance and enjoyment an effortless experience. Whether it’s managing day-to-day operations or ensuring the best conditions for swimming and relaxation, Intellitouch ScreenLogic is designed to elevate the experience of pool ownership.