Pentair Intellitouch ScreenLogic manual IntelliFlo 4x160 Alarm and Warnings

Page 104

94

IntelliFlo 4x160 Alarm and Warnings

The IntelliFlo 4 alarm and warnings are indicated by flashing LEDs on the control panel. For example, if a “Drive Temperature” warning occurs, the LED will blink two times, then Off, then blink two times. This sequence is repeated until the condition is cleared.

•Warning condition: If a warning condition occurs the pump will be continue to run but at a reduced speed. The Green LED executes a sequence of blinks to indicate which alarm or warning has occurred.

•Alarm condition: If an alarm condition occurs the pump will drive stop running. The red LED flashes continuously to indicate the presence of an alarm. The alarm LEDs will reset when the condition clears.

For IntelliFlo troubleshooting information, see the IntelliFlo 4x160 Installation and User’s Guide (P/N 357269).

Alarm and warnings LED sequence

	Number of time the	Alarm	Description	Action
	LED will blink	Alarm	Description	Action
	LED will blink

	2	Drive Temperature Warning	Excessive drive temperature	1. Ensure the motor fan has
					adequate area for ventilation.
				2. Stop motor and allow to cool.
				3. Run motor at a higher speed to
					improve cooling air flow.

	5	Unknown alarm	Electron failure	1.	Cycle power to reset pump.
				2.	Replace drive.

	6	Drive Temperature Alarm	Excessive drive temperature	1. Ensure the motor fan has
					adequate area for ventilation.
				2. Run motor at a higher speed to
					improve cooling air flow.

	7	Power Out Alarm	Supply voltage low	Ensure proper supply voltage.

	8	Over current Alarm	Excessive drive current	1. Examine fluid/mechanical
					system for source of overload.
				2. De-energize motor and
					determine if motor spins freely.
				3. Replace drive.

	9	Over voltage Alarm	Excessive voltage on drive buss	1. Rapid switching between speeds
					can cause excessive voltages
					on the drive's DC buss.
				2. Ensure proper supply voltage.

IntelliTouch ScreenLogic User’s Guide

Image 104

Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Using ScreenLogic Frequently Asked Questions FAQs and TroubleshootingAppendix Glossary 102Important Safety Precautions Important Safety Precautions Vii Related IntelliTouch Manuals About this User’s GuideTechnical Support Introduction IntelliTouch System OverviewLoad or Power Center IntelliTouch System ComponentsIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch ScreenLogic Interface Accessory Kits IntelliTouch Interface ScreenLogic KitsBlank PDA, in-Wall Touch Screen Tablet Overview Personal Digital Assistant PDA Description PDA Front and Side ViewsPDA Rear View In-Wall Touch Screen In-Wall Touch Screen ControlsTablet Overview Tablet Controls and LightsTablet Functions Tablet LightsUsing your ScreenLogic Interface Important Precautions Tablet, PDA, and In-wall Touch ScreenCold Boot/Power On-Off/Reset PDA Save System Settings Tablet and In-Wall Touch ScreenLow Battery Condition Tablet and PDA Power on and OFF Tablet and PDABattery and Power Management Tablet Battery and Power Management PDAInstallation Connection Steps Summary Before You BeginTools Required Less walls and ceilings equals better wireless reception ScreenLogic Location RequirementsRecommended Wireless Router and Protocol adapter Location Location Requirements Cable Distance LimitsProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to your Home Network with Broadband Access Connecting to an existing home networkRJ11 for DSL Coax for Cable Connect to the Protocol Adapter Proceed to Connect to the Personality Board,Connecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Start the Configurator Utility on the PDA Transfer Time from the Configurator UtilityCompatibility with IntelliTouch Systems Start ScreenLogic ProgramScreenLogic Configuration and Maintenance Screen General SettingsName Description Calibrating Temperature Sensors Changing the Display to Show Fahrenheit to CelsiusSetup Circuits Feature Circuit Configuration Button Special Lights ButtonFeature Macro Circuits Overview Freeze ProtectionAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro IntelliTouch Indoor Control Panel Circuit Names Creating Custom Names for Auxiliary CircuitsDisplay a Circuit Function Button on the Main Screen Configure Other Equipment Circuits Assigned to Valve Assign a circuit to a valvePump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up Additional Equipment Setting up a Two-Speed PumpSetup Solar Equipment and Heat pump option Set a Cool-Down Cycle for the HeaterActivate the Chlorinator Control Interface Enable Manual Spa Heat ControlChlorine Generator Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Main Screen Pool/Spa heat controls The HeatSource Configuring Pool and Spa Heating System Options Change the Pool and Spa Temperature Changing Pool Heat SettingsChanging Spa Heat Settings Main Lights ScreenColor Lights Tab Lights Screen Dim LightsSpecial Lighting Features Lights Screen Configure Set Colors Tab Color Set Name DescriptionLights Screen Configure Swimming Colors Tab Color Set Lighting Feature Set up Swimming Colors Color SwimSwitching Lights All on/All off Color SyncSave and Recall buttons Lights Screen IntelliBriteColor light show and fixed color buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen Enable/Disable Spa-Side Remotes System Error MessagesSystem Delay Cancel Feature Equipment Chlorinator Screen Chlorinator Status and Controls ScreenEquipment IntelliFlo Screen IntelliFlo Status and IntelliFlo Controls ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Status and IntelliFlo 4x160 Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for detailsBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Tips and FAQs ScreenLogic Technical Support QuestionsScreenLogic Error Messages To enter wireless settings for the TabletIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide PDA Tips and FAQs Starting Up the TabletPDA On/Off Button Turn off Backlight How can I calibrate the PDA screen?Do I need to load any software to get started? Is there anything I need to assemble before I turn it on? Connecting Please Wait message How do I switch the Tablet off? My Digital Tablet will not switch on How do I make the panel brighter/darker?Cleaning the Touch Screen Tablet comes with a desktop cradle what are its functions?IntelliFlo Alarms and Warnings Suction BlockageIntelliFlo 4x160 Alarm and Warnings Alarm and warnings LED sequenceAppendix Range Extender Kit Description ScreenLogic Wireless Connection Kit Load Center to Protocol Adapter wireless connection diagramConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C