Pentair Intellitouch ScreenLogic manual PDA Rear View

Page 19

9

PDA Front and Side Views (Continued)

Power Button: Press the power button to turn the device on or off. Press and hold the power button to dim the display. Repeat to light the display.

•When the device is connected to external power and the main battery is fully charged, the power button light is solid green.

•When the battery charge is low, the power button light flashes amber.

•When the battery is being charged, the power button light is solid amber.

•When the device relays a notification, the power button light rapidly flashes green.

Touch Screen: Use the touch screen and the stylus to enter information into your device.

On/Off Button for WAN/Bluetooth® wireless technology: This button turns the wireless device on and off. Tap it twice to confirm the switching off or on of WLAN/Bluetooth. Bluetooth is not used by IntelliTouch ScreenLogic. Switch off the wireless device to conserve power.


Current wireless status		Switch	Change wireless status
WLAN	Bluetooth		WLAN	Bluetooth
Off	Off		On	On
On	Off		Off	Off
Off	On		Off	Off
On	On		Off	Off

Home Button: Press this button to launch the Home window or to turn on the device.

Navigator Button: Press the right, left, top, or bottom of the navigator button to move the cursor on the screen. Press the center to enter a selection.

Contacts Button: Press this button to launch Contacts or to turn on the device.

Calendar Button: Press this button to launch Calendar or to turn on the device.

Record Button: Press this button to start recording audio.

Lock Button: Use lock the device, keys and touch screen.

Stylus

Reset button

Battery cover (inside)

PDA Rear View

Battery Lock: Use this switch to release and remove the battery.

Battery cover: Battery cover.

Cradle/Sync/Cable Connector: Connect a cradle or sync cable.

Reset Button: Reboots the PDA.

Cradle/Sync and	Battery lock
Cable Connector

IntelliTouch ScreenLogic User’s Guide

Image 19

Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Frequently Asked Questions FAQs and Troubleshooting Using ScreenLogicGlossary 102 AppendixImportant Safety Precautions Important Safety Precautions Vii Technical Support About this User’s GuideRelated IntelliTouch Manuals IntelliTouch System Overview IntroductionIntelliTouch System Components Load or Power CenterIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch Interface ScreenLogic Kits IntelliTouch ScreenLogic Interface Accessory Kits Blank PDA, in-Wall Touch Screen Tablet Overview PDA Front and Side Views Personal Digital Assistant PDA DescriptionPDA Rear View In-Wall Touch Screen Controls In-Wall Touch ScreenTablet Controls and Lights Tablet OverviewTablet Lights Tablet FunctionsSave System Settings Tablet and In-Wall Touch Screen Using your ScreenLogic InterfaceImportant Precautions Tablet, PDA, and In-wall Touch Screen Cold Boot/Power On-Off/Reset PDABattery and Power Management PDA Low Battery Condition Tablet and PDAPower on and OFF Tablet and PDA Battery and Power Management TabletInstallation Tools Required Before You BeginConnection Steps Summary ScreenLogic Location Requirements Less walls and ceilings equals better wireless receptionLocation Requirements Cable Distance Limits Recommended Wireless Router and Protocol adapter LocationProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to an existing home network Connecting to your Home Network with Broadband AccessRJ11 for DSL Coax for Cable Proceed to Connect to the Personality Board, Connect to the Protocol AdapterConnecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Start ScreenLogic Program Start the Configurator Utility on the PDATransfer Time from the Configurator Utility Compatibility with IntelliTouch SystemsGeneral Settings ScreenLogic Configuration and Maintenance ScreenName Description Changing the Display to Show Fahrenheit to Celsius Calibrating Temperature SensorsSetup Circuits Special Lights Button Feature Circuit Configuration ButtonFreeze Protection Feature Macro Circuits OverviewAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro Display a Circuit Function Button on the Main Screen Creating Custom Names for Auxiliary CircuitsIntelliTouch Indoor Control Panel Circuit Names Circuits Assigned to Valve Assign a circuit to a valve Configure Other EquipmentPump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up a Two-Speed Pump Setting up Additional EquipmentSet a Cool-Down Cycle for the Heater Setup Solar Equipment and Heat pump optionChlorine Generator Enable Manual Spa Heat ControlActivate the Chlorinator Control Interface Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Pool/Spa heat controls The Heat Main ScreenSource Configuring Pool and Spa Heating System Options Main Lights Screen Change the Pool and Spa TemperatureChanging Pool Heat Settings Changing Spa Heat SettingsColor Lights Tab Dim Lights Lights ScreenSpecial Lighting Features Name Description Lights Screen Configure Set Colors Tab Color SetLights Screen Configure Swimming Colors Tab Set up Swimming Colors Color Swim Color Set Lighting FeatureColor Sync Switching Lights All on/All offColor light show and fixed color buttons Lights Screen IntelliBriteSave and Recall buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen System Delay Cancel Feature System Error MessagesEnable/Disable Spa-Side Remotes Chlorinator Status and Controls Screen Equipment Chlorinator ScreenIntelliFlo Status and IntelliFlo Controls Screen Equipment IntelliFlo ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for details IntelliFlo Status and IntelliFlo 4x160 Controls ScreenBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Technical Support Questions ScreenLogic Tips and FAQsTo enter wireless settings for the Tablet ScreenLogic Error MessagesIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide How can I calibrate the PDA screen? PDA Tips and FAQsStarting Up the Tablet PDA On/Off Button Turn off BacklightIs there anything I need to assemble before I turn it on? Do I need to load any software to get started?How do I make the panel brighter/darker? Connecting Please Wait messageHow do I switch the Tablet off? My Digital Tablet will not switch onTablet comes with a desktop cradle what are its functions? Cleaning the Touch ScreenSuction Blockage IntelliFlo Alarms and WarningsAlarm and warnings LED sequence IntelliFlo 4x160 Alarm and WarningsAppendix Range Extender Kit Description Load Center to Protocol Adapter wireless connection diagram ScreenLogic Wireless Connection KitConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C