Pentair Intellitouch ScreenLogic manual Equipment Chlorinator Screen

Page 88

78

Equipment: Chlorinator Screen

Use the Equipment screen to control various system functions and view the system status.

Chlorinator Status and Controls Screen

To access the Chlorinator status and controls screen:

1. From the main ScreenLogic screen, tap the Equipment and Chlorinator tab. The chlorinator screen shows:

•Chlorinator Status: Shows the current chlorinator operating condition. If an error is detected, the displayed error message box is highlighted in yellow.

•Pool Output: Displays the pool chlorination output level from 0 to 100%. Tap the left or right arrow to increase or decrease the pool chlorination output level. The IntelliTouch system will automatically drop the chlorine output levels to 1/20 the output when the Spa mode is switched on. For example, if the pool output level is set to 60%, when the Spa is switched on, the chlorination output level will be 3%.

•Spa Output: Displays the spa chlorination output level from 0 to 100%. Tap the left or right arrow to increase or decrease the spa chlorination output level.

•Super Chlorinate: Tap the Start button to start “Super Chlorination” for 24 hours. Tap the Stop button to stop Super Chlorination. The default run time is 24 hours.

•Salt Level: Displays how much salt (in ppm: parts per million) is in the water. The color of the status bar indicates the condition of the water. Corresponding information is displayed under the status bar.Also see the chlorinator manufacturer’s instructions for recommended salt levels.

IntelliTouch ScreenLogic User’s Guide

Image 88

Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Using ScreenLogic Frequently Asked Questions FAQs and TroubleshootingAppendix Glossary 102Important Safety Precautions Important Safety Precautions Vii Technical Support About this User’s GuideRelated IntelliTouch Manuals Introduction IntelliTouch System OverviewLoad or Power Center IntelliTouch System ComponentsIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch ScreenLogic Interface Accessory Kits IntelliTouch Interface ScreenLogic KitsBlank PDA, in-Wall Touch Screen Tablet Overview Personal Digital Assistant PDA Description PDA Front and Side ViewsPDA Rear View In-Wall Touch Screen In-Wall Touch Screen ControlsTablet Overview Tablet Controls and LightsTablet Functions Tablet LightsUsing your ScreenLogic Interface Important Precautions Tablet, PDA, and In-wall Touch ScreenCold Boot/Power On-Off/Reset PDA Save System Settings Tablet and In-Wall Touch ScreenLow Battery Condition Tablet and PDA Power on and OFF Tablet and PDABattery and Power Management Tablet Battery and Power Management PDAInstallation Tools Required Before You BeginConnection Steps Summary Less walls and ceilings equals better wireless reception ScreenLogic Location RequirementsRecommended Wireless Router and Protocol adapter Location Location Requirements Cable Distance LimitsProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to your Home Network with Broadband Access Connecting to an existing home networkRJ11 for DSL Coax for Cable Connect to the Protocol Adapter Proceed to Connect to the Personality Board,Connecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Start the Configurator Utility on the PDA Transfer Time from the Configurator UtilityCompatibility with IntelliTouch Systems Start ScreenLogic ProgramScreenLogic Configuration and Maintenance Screen General SettingsName Description Calibrating Temperature Sensors Changing the Display to Show Fahrenheit to CelsiusSetup Circuits Feature Circuit Configuration Button Special Lights ButtonFeature Macro Circuits Overview Freeze ProtectionAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro Display a Circuit Function Button on the Main Screen Creating Custom Names for Auxiliary CircuitsIntelliTouch Indoor Control Panel Circuit Names Configure Other Equipment Circuits Assigned to Valve Assign a circuit to a valvePump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up Additional Equipment Setting up a Two-Speed PumpSetup Solar Equipment and Heat pump option Set a Cool-Down Cycle for the HeaterChlorine Generator Enable Manual Spa Heat ControlActivate the Chlorinator Control Interface Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Main Screen Pool/Spa heat controls The HeatSource Configuring Pool and Spa Heating System Options Change the Pool and Spa Temperature Changing Pool Heat SettingsChanging Spa Heat Settings Main Lights ScreenColor Lights Tab Lights Screen Dim LightsSpecial Lighting Features Lights Screen Configure Set Colors Tab Color Set Name DescriptionLights Screen Configure Swimming Colors Tab Color Set Lighting Feature Set up Swimming Colors Color SwimSwitching Lights All on/All off Color SyncColor light show and fixed color buttons Lights Screen IntelliBriteSave and Recall buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen System Delay Cancel Feature System Error MessagesEnable/Disable Spa-Side Remotes Equipment Chlorinator Screen Chlorinator Status and Controls ScreenEquipment IntelliFlo Screen IntelliFlo Status and IntelliFlo Controls ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Status and IntelliFlo 4x160 Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for detailsBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Tips and FAQs ScreenLogic Technical Support QuestionsScreenLogic Error Messages To enter wireless settings for the TabletIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide PDA Tips and FAQs Starting Up the TabletPDA On/Off Button Turn off Backlight How can I calibrate the PDA screen?Do I need to load any software to get started? Is there anything I need to assemble before I turn it on?Connecting Please Wait message How do I switch the Tablet off?My Digital Tablet will not switch on How do I make the panel brighter/darker?Cleaning the Touch Screen Tablet comes with a desktop cradle what are its functions?IntelliFlo Alarms and Warnings Suction BlockageIntelliFlo 4x160 Alarm and Warnings Alarm and warnings LED sequenceAppendix Range Extender Kit Description ScreenLogic Wireless Connection Kit Load Center to Protocol Adapter wireless connection diagramConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C