Pentair Intellitouch ScreenLogic manual Changing the Display to Show Fahrenheit to Celsius

Page 44

34

Changing the Display to Show Fahrenheit to Celsius

Temperature set point and actual temperature settings are displayed on the Main screen in either Fahrenheit or Celsius.

To change the temperature scale:

1.Start the ScreenLogic Configurator utility, and tap Configure IntelliTouch.

2.On the General Setting page under Temperature Scale, tap either Fahrenheit or Celsius.

3.Tap Finish when done to save the setting.

Calibrating Temperature Sensors

The IntelliTouch system includes two temperature sensors (10 kohm) for water and ambient air temperature. The IntelliTouch i10+3D model for dual bodies of water has three sensors. You can add an additional sensor for controlling solar heating systems.

Generally, these sensors are accurate and you do not have to calibrate them. However, long plumbing runs and water features can cause temperatures at a body of water to be different from the temperature sensor reading. You can manually recalibrate the sensors to adjust for this.

Before you start, you need an accurate all weather thermometer. If you are calibrating the air sensor, wait until the sensor is not in direct sunlight.

There is a Water Temp and Air Temp setting. If you have an i10+3D system, you will see Spa Temp, Pool Temp, and Air Temp. Calibrate the Spa and Pool temperatures the same way as described below for Water Temp. For the i5, i5S, i7+3, or i9+3 system, there is a water and air temperature sensor. Make sure to locate the air temperature sensor in the shade for accurate readings.

To calibrate the air, pool and spa sensors:

1.First, tap the Pool or Spa button on the ScreenLogic Main screen to switch on the spa or pool filter pump.

2.Tap Configure IntelliTouch to start the ScreenLogic Configurator.

3.Place the thermometer in the spa or pool. Take an accurate temperature reading. When calibrating the air sensor, place the thermometer next to the air sensor. The sensor is normally located near or under the Load Center or Power Center enclosure, not inside the enclosure. Take an accurate temperature reading in the shade.

4.On the General Setting page under Calibrate Sensors, use the Up or Down arrows to raise or lower the Air, Pool and Spa temperature to match the corresponding thermometer temperature reading. If you have an i10+3D repeat the above for the pool. The i10+3D has three sensors, one each for the spa and pool water and one for the air temperature.

5.Press Finish when done.

IntelliTouch ScreenLogic User’s Guide

Page 43 Page 45
Image 44
Page 43 Page 45
Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Using ScreenLogic Frequently Asked Questions FAQs and TroubleshootingAppendix Glossary 102Important Safety Precautions Important Safety Precautions Vii Related IntelliTouch Manuals About this User’s GuideTechnical Support Introduction IntelliTouch System OverviewLoad or Power Center IntelliTouch System ComponentsIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch ScreenLogic Interface Accessory Kits IntelliTouch Interface ScreenLogic KitsBlank PDA, in-Wall Touch Screen Tablet Overview Personal Digital Assistant PDA Description PDA Front and Side ViewsPDA Rear View In-Wall Touch Screen In-Wall Touch Screen ControlsTablet Overview Tablet Controls and LightsTablet Functions Tablet LightsUsing your ScreenLogic Interface Important Precautions Tablet, PDA, and In-wall Touch ScreenCold Boot/Power On-Off/Reset PDA Save System Settings Tablet and In-Wall Touch ScreenLow Battery Condition Tablet and PDA Power on and OFF Tablet and PDABattery and Power Management Tablet Battery and Power Management PDAInstallation Connection Steps Summary Before You BeginTools Required Less walls and ceilings equals better wireless reception ScreenLogic Location RequirementsRecommended Wireless Router and Protocol adapter Location Location Requirements Cable Distance LimitsProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to your Home Network with Broadband Access Connecting to an existing home networkRJ11 for DSL Coax for Cable Connect to the Protocol Adapter Proceed to Connect to the Personality Board,Connecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Start the Configurator Utility on the PDA Transfer Time from the Configurator UtilityCompatibility with IntelliTouch Systems Start ScreenLogic ProgramScreenLogic Configuration and Maintenance Screen General SettingsName Description Calibrating Temperature Sensors Changing the Display to Show Fahrenheit to CelsiusSetup Circuits Feature Circuit Configuration Button Special Lights ButtonFeature Macro Circuits Overview Freeze ProtectionAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro IntelliTouch Indoor Control Panel Circuit Names Creating Custom Names for Auxiliary CircuitsDisplay a Circuit Function Button on the Main Screen Configure Other Equipment Circuits Assigned to Valve Assign a circuit to a valvePump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up Additional Equipment Setting up a Two-Speed PumpSetup Solar Equipment and Heat pump option Set a Cool-Down Cycle for the HeaterActivate the Chlorinator Control Interface Enable Manual Spa Heat ControlChlorine Generator Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Main Screen Pool/Spa heat controls The HeatSource Configuring Pool and Spa Heating System Options Change the Pool and Spa Temperature Changing Pool Heat SettingsChanging Spa Heat Settings Main Lights ScreenColor Lights Tab Lights Screen Dim LightsSpecial Lighting Features Lights Screen Configure Set Colors Tab Color Set Name DescriptionLights Screen Configure Swimming Colors Tab Color Set Lighting Feature Set up Swimming Colors Color SwimSwitching Lights All on/All off Color SyncSave and Recall buttons Lights Screen IntelliBriteColor light show and fixed color buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen Enable/Disable Spa-Side Remotes System Error MessagesSystem Delay Cancel Feature Equipment Chlorinator Screen Chlorinator Status and Controls ScreenEquipment IntelliFlo Screen IntelliFlo Status and IntelliFlo Controls ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Status and IntelliFlo 4x160 Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for detailsBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Tips and FAQs ScreenLogic Technical Support QuestionsScreenLogic Error Messages To enter wireless settings for the TabletIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide PDA Tips and FAQs Starting Up the TabletPDA On/Off Button Turn off Backlight How can I calibrate the PDA screen?Do I need to load any software to get started? Is there anything I need to assemble before I turn it on?Connecting Please Wait message How do I switch the Tablet off?My Digital Tablet will not switch on How do I make the panel brighter/darker?Cleaning the Touch Screen Tablet comes with a desktop cradle what are its functions?IntelliFlo Alarms and Warnings Suction BlockageIntelliFlo 4x160 Alarm and Warnings Alarm and warnings LED sequenceAppendix Range Extender Kit Description ScreenLogic Wireless Connection Kit Load Center to Protocol Adapter wireless connection diagramConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C

Intellitouch ScreenLogic specifications

Pentair Intellitouch ScreenLogic is a cutting-edge control system designed for pool and spa automation, delivering enhanced convenience and efficiency for homeowners. This innovative system allows users to control and manage their swimming pool and spa features through a user-friendly interface, providing comprehensive management from both local and remote locations.

One of the standout features of Intellitouch ScreenLogic is its intuitive touchscreen interface. Users can easily navigate through various settings and functionalities, ensuring a hassle-free experience when adjusting pool temperatures, controlling lights, and managing water features. The interface is designed to be visually appealing and straightforward, accommodating both tech-savvy individuals and those who might find technology overwhelming.

The system's connectivity options are another significant advantage. Intellitouch ScreenLogic integrates seamlessly with a variety of devices, including smartphones and tablets, through the ScreenLogic2 app. This feature allows users to control their pool systems anytime, anywhere, providing unparalleled remote access. Whether you want to heat the spa before arriving home or change the lighting for an evening gathering, the app allows you to manage all aspects effortlessly.

Enhancing customization, Intellitouch ScreenLogic supports various automation options, which can be tailored to meet individual preferences. Homeowners can set schedules for cleaning systems, heating, and lighting, allowing for energy-efficient management. This automation not only adds convenience but also contributes to reducing energy consumption and operational costs.

Furthermore, Pentair's advanced technologies extend beyond simple controls. The system can monitor water quality and provide alerts regarding chemical levels, ensuring that pools remain safe and hygienic. Additionally, the integration of energy-efficient components, such as variable-speed pumps and LED lighting, optimizes energy use, leading to further savings.

In summary, Pentair Intellitouch ScreenLogic stands as a leading solution in pool and spa automation, boasting a user-friendly touchscreen interface, robust remote connectivity, customizable automation features, and advanced monitoring technologies. By investing in this innovative system, pool owners can enjoy enhanced convenience, efficiency, and peace of mind, making pool maintenance and enjoyment an effortless experience. Whether it’s managing day-to-day operations or ensuring the best conditions for swimming and relaxation, Intellitouch ScreenLogic is designed to elevate the experience of pool ownership.
Top Page Image Contents