Pentair Intellitouch ScreenLogic manual IntelliFlo Status and IntelliFlo Controls Screen

Page 90

80

IntelliFlo Status and IntelliFlo Controls Screen (Continued)

•IntelliFlo Output (Pump Off/Pump On): The Pump Off box is displayed in yellow when the pump is off and not operating. The Pump On box is displayed in yellow when the pump is operating. The Power Usage (Watts), RPM, and Flow (GPM) display the current status while the pump is operating. If the “Pump On” box displays in yellow and there are no buttons active on this screen (yellow), it indicates that the pump is operating and maybe “filtering” the pool.

•Power Usage (Watts), RPM, and Flow (GPM) status indicators: The pump status indicators show the current power usage in Watts, speed, in revolutions per minute (RPM), and flow, in gallons per minute (GPM) while the pump is operating.

•Filter Status: Displays the current percent status of the filter as set in the “Clean Filter PSI” setting (see page 52). Typically when the Filter Status displays 24% it indicates that the filter requires cleaning (or a Backwash). When the pump detects that the filter differential pressure (10 PSI difference) has increased and is now at the “Clean Filter” pressure, the ScreenLogic pump status “Filter Warning” displays in yellow indicating that the filter must be cleaned (backwashed) to reduce the pressure. You need to stop IntelliFlo, place IntelliTouch in “Service” mode, press the Start/Stop button on IntelliFlo, then press the Backwash button to start the backwash flow operation. IntelliFlo will run the preset cycle time and preset flow GPM). The flow will be adjustable to accommodate the specific filter backwash flow requirement.After the backwash cycle is finished, the “Rinse” cycle with the preset duration time will be executed.After these cycles have been completed or if the Start/Stop button is pressed to stop the process, the filter status will be recalculated and the zero-pressure measured when Filter mode is operated again.

IntelliTouch ScreenLogic User’s Guide

Image 90

Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Using ScreenLogic Frequently Asked Questions FAQs and TroubleshootingAppendix Glossary 102Important Safety Precautions Important Safety Precautions Vii About this User’s Guide Technical SupportRelated IntelliTouch Manuals Introduction IntelliTouch System OverviewLoad or Power Center IntelliTouch System ComponentsIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch ScreenLogic Interface Accessory Kits IntelliTouch Interface ScreenLogic KitsBlank PDA, in-Wall Touch Screen Tablet Overview Personal Digital Assistant PDA Description PDA Front and Side ViewsPDA Rear View In-Wall Touch Screen In-Wall Touch Screen ControlsTablet Overview Tablet Controls and LightsTablet Functions Tablet LightsCold Boot/Power On-Off/Reset PDA Using your ScreenLogic InterfaceImportant Precautions Tablet, PDA, and In-wall Touch Screen Save System Settings Tablet and In-Wall Touch ScreenBattery and Power Management Tablet Low Battery Condition Tablet and PDAPower on and OFF Tablet and PDA Battery and Power Management PDAInstallation Before You Begin Tools RequiredConnection Steps Summary Less walls and ceilings equals better wireless reception ScreenLogic Location RequirementsRecommended Wireless Router and Protocol adapter Location Location Requirements Cable Distance LimitsProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to your Home Network with Broadband Access Connecting to an existing home networkRJ11 for DSL Coax for Cable Connect to the Protocol Adapter Proceed to Connect to the Personality Board,Connecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Compatibility with IntelliTouch Systems Start the Configurator Utility on the PDATransfer Time from the Configurator Utility Start ScreenLogic ProgramScreenLogic Configuration and Maintenance Screen General SettingsName Description Calibrating Temperature Sensors Changing the Display to Show Fahrenheit to CelsiusSetup Circuits Feature Circuit Configuration Button Special Lights ButtonFeature Macro Circuits Overview Freeze ProtectionAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro Creating Custom Names for Auxiliary Circuits Display a Circuit Function Button on the Main ScreenIntelliTouch Indoor Control Panel Circuit Names Configure Other Equipment Circuits Assigned to Valve Assign a circuit to a valvePump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up Additional Equipment Setting up a Two-Speed PumpSetup Solar Equipment and Heat pump option Set a Cool-Down Cycle for the HeaterEnable Manual Spa Heat Control Chlorine GeneratorActivate the Chlorinator Control Interface Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Main Screen Pool/Spa heat controls The HeatSource Configuring Pool and Spa Heating System Options Changing Spa Heat Settings Change the Pool and Spa TemperatureChanging Pool Heat Settings Main Lights ScreenColor Lights Tab Lights Screen Dim LightsSpecial Lighting Features Lights Screen Configure Set Colors Tab Color Set Name DescriptionLights Screen Configure Swimming Colors Tab Color Set Lighting Feature Set up Swimming Colors Color SwimSwitching Lights All on/All off Color SyncLights Screen IntelliBrite Color light show and fixed color buttonsSave and Recall buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen System Error Messages System Delay Cancel Feature Enable/Disable Spa-Side Remotes Equipment Chlorinator Screen Chlorinator Status and Controls ScreenEquipment IntelliFlo Screen IntelliFlo Status and IntelliFlo Controls ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Status and IntelliFlo 4x160 Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for detailsBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Tips and FAQs ScreenLogic Technical Support QuestionsScreenLogic Error Messages To enter wireless settings for the TabletIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide PDA On/Off Button Turn off Backlight PDA Tips and FAQsStarting Up the Tablet How can I calibrate the PDA screen?Do I need to load any software to get started? Is there anything I need to assemble before I turn it on?My Digital Tablet will not switch on Connecting Please Wait messageHow do I switch the Tablet off? How do I make the panel brighter/darker?Cleaning the Touch Screen Tablet comes with a desktop cradle what are its functions?IntelliFlo Alarms and Warnings Suction BlockageIntelliFlo 4x160 Alarm and Warnings Alarm and warnings LED sequenceAppendix Range Extender Kit Description ScreenLogic Wireless Connection Kit Load Center to Protocol Adapter wireless connection diagramConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C