Pentair Intellitouch ScreenLogic manual Connect to the Protocol Adapter

Page 34

24

Connect to the Protocol Adapter

The IntelliTouch ScreenLogic Protocol adapter is connected to the Personality board located in the Load Center or Power Center via a four-wire cable. Before connecting the cable to the adapter, first determine the length of cable required for the connection.

ProtocolAdapter Location: The IntelliTouch wireless router and Protocol adapter should be located inside in a dry environment, preferably near the home owners DSL/Cable modem. If the wireless router is too far from the pool area, then you may need to move the wireless router closer to the pool area by running an Ethernet cable from the DSL/Cable Modem connection out to the Protocol adapter and wireless router. For wireless router location requirement, refer to “ScreenLogic Location Requirements,” page 17.

Note: Existing IndoorControl Panel - If there is an existing IntelliTouch Indoor Control Panel, you can tap directly into the wire in the home or pig tail off the connector in the Indoor Control Panel. This avoids having to run a separate four wire from the Load Center to the Protocol adapter.

To connect to the Protocol adapter:

1.Connect the Four-Wire Cable: Run a four conductor cable (22 AWG UL approved) from the Load Center or Power Center location to the adapter. Place the adapter in a dry area near the wireless router. Ideally, both devices should be located near the home owners DSL or Cable modem.

2.Grasp the Protocol adapter with one hand, and with your other hand gently pull outward on screw terminal connector to remove it from its socket.

3.Strip back the four cable conductors ¼ inch. Insert the four wires into the connector screw terminals. Secure the wires with the four screws. Make sure to match the color coding of the wires with the pin colors indicated on the adapter label. The pin numbers and wire color codes are:

1BLK = Ground

2GRN = -DT

3YEL = +DT

4RED = +15 VDC

4.Insert the screw terminal connector onto the pins on the adapter circuit board. Note that the connector is keyed for the correct orientation.

5.Proceed to “Connect to the Personality Board,” page 25.

Screw terminal connector

BLK = Ground (1)

GRN = -DT(2)

YEL = +DT(3)

RED = + 15 VDC (4)

Pull connector

 

out to remove

Protocol Adapter

 

Ethernet (RJ45)

 

connector for

 

connection to

 

wireless router

IntelliTouch ScreenLogic User’s Guide

Image 34
Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Using ScreenLogic Frequently Asked Questions FAQs and TroubleshootingAppendix Glossary 102Important Safety Precautions Important Safety Precautions Vii Technical Support About this User’s GuideRelated IntelliTouch Manuals Introduction IntelliTouch System OverviewLoad or Power Center IntelliTouch System ComponentsIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch ScreenLogic Interface Accessory Kits IntelliTouch Interface ScreenLogic KitsBlank PDA, in-Wall Touch Screen Tablet Overview Personal Digital Assistant PDA Description PDA Front and Side ViewsPDA Rear View In-Wall Touch Screen In-Wall Touch Screen ControlsTablet Overview Tablet Controls and LightsTablet Functions Tablet LightsCold Boot/Power On-Off/Reset PDA Using your ScreenLogic InterfaceImportant Precautions Tablet, PDA, and In-wall Touch Screen Save System Settings Tablet and In-Wall Touch ScreenBattery and Power Management Tablet Low Battery Condition Tablet and PDAPower on and OFF Tablet and PDA Battery and Power Management PDAInstallation Tools Required Before You BeginConnection Steps Summary Less walls and ceilings equals better wireless reception ScreenLogic Location RequirementsRecommended Wireless Router and Protocol adapter Location Location Requirements Cable Distance LimitsProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to your Home Network with Broadband Access Connecting to an existing home networkRJ11 for DSL Coax for Cable Connect to the Protocol Adapter Proceed to Connect to the Personality Board,Connecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Compatibility with IntelliTouch Systems Start the Configurator Utility on the PDATransfer Time from the Configurator Utility Start ScreenLogic ProgramScreenLogic Configuration and Maintenance Screen General SettingsName Description Calibrating Temperature Sensors Changing the Display to Show Fahrenheit to CelsiusSetup Circuits Feature Circuit Configuration Button Special Lights ButtonFeature Macro Circuits Overview Freeze ProtectionAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro Display a Circuit Function Button on the Main Screen Creating Custom Names for Auxiliary CircuitsIntelliTouch Indoor Control Panel Circuit Names Configure Other Equipment Circuits Assigned to Valve Assign a circuit to a valvePump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up Additional Equipment Setting up a Two-Speed PumpSetup Solar Equipment and Heat pump option Set a Cool-Down Cycle for the HeaterChlorine Generator Enable Manual Spa Heat ControlActivate the Chlorinator Control Interface Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Main Screen Pool/Spa heat controls The HeatSource Configuring Pool and Spa Heating System Options Changing Spa Heat Settings Change the Pool and Spa TemperatureChanging Pool Heat Settings Main Lights ScreenColor Lights Tab Lights Screen Dim LightsSpecial Lighting Features Lights Screen Configure Set Colors Tab Color Set Name DescriptionLights Screen Configure Swimming Colors Tab Color Set Lighting Feature Set up Swimming Colors Color SwimSwitching Lights All on/All off Color SyncColor light show and fixed color buttons Lights Screen IntelliBriteSave and Recall buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen System Delay Cancel Feature System Error MessagesEnable/Disable Spa-Side Remotes Equipment Chlorinator Screen Chlorinator Status and Controls ScreenEquipment IntelliFlo Screen IntelliFlo Status and IntelliFlo Controls ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Status and IntelliFlo 4x160 Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for detailsBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Tips and FAQs ScreenLogic Technical Support QuestionsScreenLogic Error Messages To enter wireless settings for the TabletIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide PDA On/Off Button Turn off Backlight PDA Tips and FAQsStarting Up the Tablet How can I calibrate the PDA screen?Do I need to load any software to get started? Is there anything I need to assemble before I turn it on?My Digital Tablet will not switch on Connecting Please Wait messageHow do I switch the Tablet off? How do I make the panel brighter/darker?Cleaning the Touch Screen Tablet comes with a desktop cradle what are its functions?IntelliFlo Alarms and Warnings Suction BlockageIntelliFlo 4x160 Alarm and Warnings Alarm and warnings LED sequenceAppendix Range Extender Kit Description ScreenLogic Wireless Connection Kit Load Center to Protocol Adapter wireless connection diagramConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C

Intellitouch ScreenLogic specifications

Pentair Intellitouch ScreenLogic is a cutting-edge control system designed for pool and spa automation, delivering enhanced convenience and efficiency for homeowners. This innovative system allows users to control and manage their swimming pool and spa features through a user-friendly interface, providing comprehensive management from both local and remote locations.

One of the standout features of Intellitouch ScreenLogic is its intuitive touchscreen interface. Users can easily navigate through various settings and functionalities, ensuring a hassle-free experience when adjusting pool temperatures, controlling lights, and managing water features. The interface is designed to be visually appealing and straightforward, accommodating both tech-savvy individuals and those who might find technology overwhelming.

The system's connectivity options are another significant advantage. Intellitouch ScreenLogic integrates seamlessly with a variety of devices, including smartphones and tablets, through the ScreenLogic2 app. This feature allows users to control their pool systems anytime, anywhere, providing unparalleled remote access. Whether you want to heat the spa before arriving home or change the lighting for an evening gathering, the app allows you to manage all aspects effortlessly.

Enhancing customization, Intellitouch ScreenLogic supports various automation options, which can be tailored to meet individual preferences. Homeowners can set schedules for cleaning systems, heating, and lighting, allowing for energy-efficient management. This automation not only adds convenience but also contributes to reducing energy consumption and operational costs.

Furthermore, Pentair's advanced technologies extend beyond simple controls. The system can monitor water quality and provide alerts regarding chemical levels, ensuring that pools remain safe and hygienic. Additionally, the integration of energy-efficient components, such as variable-speed pumps and LED lighting, optimizes energy use, leading to further savings.

In summary, Pentair Intellitouch ScreenLogic stands as a leading solution in pool and spa automation, boasting a user-friendly touchscreen interface, robust remote connectivity, customizable automation features, and advanced monitoring technologies. By investing in this innovative system, pool owners can enjoy enhanced convenience, efficiency, and peace of mind, making pool maintenance and enjoyment an effortless experience. Whether it’s managing day-to-day operations or ensuring the best conditions for swimming and relaxation, Intellitouch ScreenLogic is designed to elevate the experience of pool ownership.