Pentair Intellitouch ScreenLogic manual ScreenLogic Wireless Connection Kit

Page 107

97

ScreenLogic Wireless Connection Kit

The ScreenLogic Wireless Connection kit (P/N 520639) consists of two wireless 900 Mhz transceivers which provides a wireless connection between the ScreenLogic Protocol adapter and the IntelliTouch Load Center located at the equipment pad. This wireless connection eliminates the existing hard wire connection from inside your home to the equipment pad.

The diagram below shows the wireless transceiver locations. The transceiver connected to the IntelliTouch Load Center is connected to the Personality board COM port. The other transceiver is connected to the Protocol Adapter located inside the home.

Load Center to Protocol Adapter wireless connection diagram

Existing wired or wireless
router (mandatory)		Transceiver
RJ11 for DSL		connected to
Coax for Cable		ScreenLogic
ScreenLogic	In-wall touch	Protocol adapter
Wireless router screen
INTERNET

Wireless transceiver connected to Personality board (COM port)

via 10’ cable

WAN 1 2 3 4

RJ11 RJ45

(RJ45)

DSL or

Cable Modem

Ethernet cable (RJ45 - CAT 5)

4-wire 1 foot cable

- LAN -

AC power

1 2 3 4

WAN

adapter

Ethernet cable (RJ45 - CAT 5)

Protocol

Adapter

Existing PC

Indoor Control

Panel (*)

Wireless PDA

Wireless Digital Tablet

Cable distance limits:

-Ethernet cable distance limit = 300 feet

-Four-wire cable distance limit = 1500 feet Note: (*) Optional wiring for existing Indoor Control Panel. Tap into the Indoor Control Panel connector or pig tail off the four-wire cable connected to the Personality board.

Load Center (Located outside at equipment pad)

IntelliTouch ScreenLogic User’s Guide

Image 107

Contents IntelliTouch ScreenLogic User’s Guide Pentair Water Pool and Spa, Inc Contents Configuring ScreenLogic Frequently Asked Questions FAQs and Troubleshooting Using ScreenLogicGlossary 102 AppendixImportant Safety Precautions Important Safety Precautions Vii Related IntelliTouch Manuals About this User’s GuideTechnical Support IntelliTouch System Overview IntroductionIntelliTouch System Components Load or Power CenterIntelliTouch Interfaces IntelliTouch ScreenLogic in your home IntelliTouch Interface ScreenLogic Kits IntelliTouch ScreenLogic Interface Accessory KitsBlank PDA, in-Wall Touch Screen Tablet Overview PDA Front and Side Views Personal Digital Assistant PDA DescriptionPDA Rear View In-Wall Touch Screen Controls In-Wall Touch ScreenTablet Controls and Lights Tablet OverviewTablet Lights Tablet FunctionsSave System Settings Tablet and In-Wall Touch Screen Using your ScreenLogic InterfaceImportant Precautions Tablet, PDA, and In-wall Touch Screen Cold Boot/Power On-Off/Reset PDABattery and Power Management PDA Low Battery Condition Tablet and PDAPower on and OFF Tablet and PDA Battery and Power Management TabletInstallation Connection Steps Summary Before You BeginTools Required ScreenLogic Location Requirements Less walls and ceilings equals better wireless receptionLocation Requirements Cable Distance Limits Recommended Wireless Router and Protocol adapter LocationProtocol ScreenLogic Adding Range Extender Kit for Large Home and Properties Connecting without Broadband Internet Access Connecting to an existing home network Connecting to your Home Network with Broadband AccessRJ11 for DSL Coax for Cable Proceed to Connect to the Personality Board, Connect to the Protocol AdapterConnecting to the Personality Board Personality board Connector J7 or J8 To start up the system Blank Configuring ScreenLogic Accessing IntelliTouch ScreenLogic Configuration Program Start ScreenLogic Program Start the Configurator Utility on the PDATransfer Time from the Configurator Utility Compatibility with IntelliTouch SystemsGeneral Settings ScreenLogic Configuration and Maintenance ScreenName Description Changing the Display to Show Fahrenheit to Celsius Calibrating Temperature SensorsSetup Circuits Special Lights Button Feature Circuit Configuration ButtonFreeze Protection Feature Macro Circuits OverviewAssign a Circuit Name and Function IntelliTouch Circuit Functions IntelliTouch Circuit Names Creating a Feature Circuit Macro IntelliTouch Indoor Control Panel Circuit Names Creating Custom Names for Auxiliary CircuitsDisplay a Circuit Function Button on the Main Screen Circuits Assigned to Valve Assign a circuit to a valve Configure Other EquipmentPump on during heater cool-down Select this check box if you Configuring Valve Actuators Setting up a Two-Speed Pump Setting up Additional EquipmentSet a Cool-Down Cycle for the Heater Setup Solar Equipment and Heat pump optionActivate the Chlorinator Control Interface Enable Manual Spa Heat ControlChlorine Generator Configure IntelliFlo Filtering dialog Configure IntelliFlo Configure IntelliFlo Configure iS10 Spa-Side Remote Configure iS4, iS10, and QT4 QuickTouch Using ScreenLogic Home Screen Pool/Spa heat controls The Heat Main ScreenSource Configuring Pool and Spa Heating System Options Main Lights Screen Change the Pool and Spa TemperatureChanging Pool Heat Settings Changing Spa Heat SettingsColor Lights Tab Dim Lights Lights ScreenSpecial Lighting Features Name Description Lights Screen Configure Set Colors Tab Color SetLights Screen Configure Swimming Colors Tab Set up Swimming Colors Color Swim Color Set Lighting FeatureColor Sync Switching Lights All on/All offSave and Recall buttons Lights Screen IntelliBriteColor light show and fixed color buttons Schedule Screen Schedule Feature Schedule Run Once Screen Run-Once Timer Schedule Egg Timer Screen Setting the Egg Timer Count Down History Screen Equipment System Status Screen Enable/Disable Spa-Side Remotes System Error MessagesSystem Delay Cancel Feature Chlorinator Status and Controls Screen Equipment Chlorinator ScreenIntelliFlo Status and IntelliFlo Controls Screen Equipment IntelliFlo ScreenIntelliFlo Status and IntelliFlo Controls Screen IntelliFlo Output Pump Off/Pump On See page 80 for details IntelliFlo Status and IntelliFlo 4x160 Controls ScreenBlank Frequently Asked Questions FAQs Troubleshooting ScreenLogic Technical Support Questions ScreenLogic Tips and FAQsTo enter wireless settings for the Tablet ScreenLogic Error MessagesIntelliTouch ScreenLogic User’s Guide PDA First Time Setup Instructions IntelliTouch ScreenLogic User’s Guide How can I calibrate the PDA screen? PDA Tips and FAQsStarting Up the Tablet PDA On/Off Button Turn off BacklightIs there anything I need to assemble before I turn it on? Do I need to load any software to get started?How do I make the panel brighter/darker? Connecting Please Wait messageHow do I switch the Tablet off? My Digital Tablet will not switch onTablet comes with a desktop cradle what are its functions? Cleaning the Touch ScreenSuction Blockage IntelliFlo Alarms and Warnings Alarm and warnings LED sequence IntelliFlo 4x160 Alarm and WarningsAppendix Range Extender Kit Description Load Center to Protocol Adapter wireless connection diagram ScreenLogic Wireless Connection KitConnecting remotely to your system HomeLogic Management and Control Solution In-Wall Touch Screen Installation Installation is complete Glossary Glossary 104 Page 520493 Rev. C