Citizen D710/D716 Using the Timer Mode, Setting the Timer, Timer Setting Display

Page 41

6. Using the Timer Mode

The timer of this watch can be set up to 99 minutes in 1 minute units. An alarm sound indicating that the time is up sounds for about 30 seconds and "Timer" is displayed on the display when the time on the timer is up. The timer then returns to the initial set time and stops.

In addition, the alarm sound indicating that time is up following completion of timing can be selected from 15 types of alarm sounds.

[Timer Setting Display]

(C)

Minutes, seconds

(B)

Current time

(D) (A)

Flashing

A. Setting the Timer

(1)The minutes flash when the upper left button (C) is pressed for at least 2 seconds and then released in the timer mode.

(2)Set the minutes by pressing the upper right button (B) or lower right button (A).

Pressing the upper right button (B) advances the display by one minute at a time each time it is pressed while pressing the lower right

button (A) moves back the display by one minute at a time each time it is pressed. (Pressing either button continuously causes the display to change rapidly.)

(3)The time up alarm number flashes each time the upper left button (C) is pressed.

(4)Set the time up alarm number by pressing the upper right button (B) or lower right button (A).

Pressing the upper right button (B) once calls up the next time up alarm number each time it is pressed, while pressing the lower right button (A) once calls up the next time up alarm number in the reverse order each time it is pressed. Select "Silent" when you do not want the time up alarm to sound.

You can monitor the time up alarm of the number that is flashing by pressing the upper right button (B) or lower right button (A) for as long as the button is pressed. (The next or previous time up alarm number is momentarily displayed the instant the button is pressed, while pressing either button continuously causes the set time up alarm to sound.)

(5)Press and release the lower left button (D) to return the watch to the timer setting display.

*The watch automatically returns to the timer setting display when none of the buttons are pressed for about 3 minutes in the correction state (display flashing).

*The watch can be immediately returned to the timer setting display by pressing the lower left button (D) and then releasing in the correction state (display flashing).

41

Image 41
Contents D710/ D716 Page English English English English Before UsingIntroduction Important Notes Safety Precautions Observe at All TimesGeneral Cautions Regarding Diving Page Page Page Contents Page Using the Scuba Diving Log Mode and Skin Diving Log Mode Watch Checking Accessories Prohibited Prohibited Use During Diving Page Page Various watch functions can be set on your PC FeaturesOther Convenient Functions This watch is of the rechargeable typeNames and Functions of Components ChargerPcs. of size AA Alkaline Batteries Installation Procedure Charging the Watch Watch Display During Charging Watch Display Modes Functions Standard ModeNames of Components Scuba Diving Log Mode Dive Plan ModeSkin Diving Log Mode Dive ModeHow to Read the Charge Level Indicator of the watch Charge Level Indicator and Continuous Usage TimeAmount of Charge Usage timeContinuous Usage Time UsingUsingthetheELELLightLightDive Plan Switching the ModeStandard Mode Page Using the Time Mode Using the Standard ModeSwitching the Display Day DisplaySetting the Time and Date Daily Graphic Display Normal Display Time Difference Display Using the Travel Time ModeSetting the Travel Time Before Interchanging ProcedureAfter interchanging During interchangingSetting the Destination Timer Using the Destination Timer ModeArrival Time Remaining Time Display DisplayDestination Timer Measuring Procedure Time up Remaining TimeElapsed Time Display Displaying Arrival Time Set during MeasurementAlarm ON/OFF and Alarm Monitor Using the Alarm ModeSetting the Alarm Alarm on Alarm OFFPage Reading the Display Using the Chronograph ModeChronograph Timing Procedure Timer Setting Display Using the Timer ModeSetting the Timer Repeating Measurement Timer Measuring ProcedureSetting display Timing Stop Time up Charge Level Indicator Using the System Monitor ModeCharge Level Indicator Flash Memory Status Display Garbage CollectionFlash Memory Status Display Garbage Collection Operating ProcedurePage Location IrWW Locations Displayed by this WatchLocations Pre-registered in this Watch During AIR diving Insufficient Charge Warning File Error WarningExplanation of Warning Functions Water Sensor Check Warning Abnormal Pressure Detection Error WarningAscent Rate Warning Abnormal Depth WarningPermanent Error Warning Decompression Diving ErrorExceed Maximum Depth Warning Decompression Diving WarningPO2 limit Error Permanent ErrorOxygen Toxication Time Error PO2 Limit WarningDiving Terms Used by this Watch Repetitive Diving Safety StopDecompression Diving Decompression StopDive Time Minimum Water Temperature Min.w.tempTime Maximum Depth Max. DepthSwitching the Display Using the Dive Plan ModeDive Condition Display Dive Plan Display Dive Alarm Display AIR DivingHigh-Altitude Setting Nitrox SettingSwitching from Nitrox Setting to AIR Setting Nitrox Setting and Oxygen Concentration SettingAIROxygen Concentration Setting StateNITROX Dive Condition MarksDepth Alarm Dive AlarmDive Time Alarm Calling Up No-Decompression Limit TimeDepth No. of times Alarm sounds Dive time Setting the Dive AlarmDive Alarm Monitor AIR diving Nitrox diving Calling Up Scuba Diving Log DataCalling Up Skin Diving Log Data Deleting Log Data Water Depth Measurement Display Skin diving Using the Dive ModeDuring Decompression Diving Display during AIR SettingExplanation of Display During Water Depth Measurement Display during Nitrox Setting Safety Stop Graph Display Safety Stop Graph and Decompression Stop GraphDepth Measurement Decompression Stop GraphEnding the Dive Mode Water Temperature MeasurementDive Time Measurement No. of Dives Per Day and Recording Log DataUsing the Surface Mode No Display Low power mode Temporary functionTime Display Date Display Setting the Time and Date Communication Range Data Communication FunctionsInfrared Communication Display Sequence in Infrared Communication Mode Infrared Communication Mode Operating ProcedureCommunication by USB Interface Watch SettingsData Communication with PC Diving Log and Profile DataVAttachment of Ferrite Core Preparations for CommunicationUSB Communication Sending and Receiving Data Data Communication Between WatchesReceiving Transmitting WatchWatch ProcedureAll Reset Formatting Flash Memory Operating Environment Accessory SoftwareWeb Browser When Registering Animated Images in an AlbumPrinter Installing CAPgm Watch Setting Software Page Ending Aqualand Graph Nx and CAPgm Startup and Ending Aqualand Graph Nx and CAPgmStartup of Aqualand Graph Nx and CAPgm Communication Unit Leg Removable USB Cable ConnectorAttaching and Removing the Watch Using the Communication UnitInstalling Batteries Windows98 or Windows98 SE Installing the USB DriverPage Windows Me Confirm that your personal computer has started up normally Windows2000WindowsXP Page Problem Possible Cause Corrective Action Reference TroubleshootingUnable to Slow Sounds Examples of Use Indication Handling Precautions for the watchStatic Electricity Cleaning the WatchTemperatures Storage ShocksChemical Agents, Gases and Mercury Watch SpecificationsCharger Communication Unit Sold Separately